Kaleidescape SVC-KIT-0010 User manual
Kaleidescape,Inc. July 22, 2010
This document is for informational purposes only. Kaleidescape makes no representations or warranties, express or implied, regarding the accuracy or completeness of the information
contained herein and Kaleidescape shall have no obligation to provide updates to this information in the future. Copyright © 2010 Kaleidescape, Inc. All rights reserved. Kaleidescape is
a trademark of Kaleidescape, Inc. and is registered in the United States and certain other jurisdictions. Kaleidescape Part No. 101-0142-00 Rev 1.
Instructions for SVC-KIT-0010
Title Movie Player (KPLAYER-2500) Power Supply and Fan Replacement
Time to complete 1 hour
Procedure to complete
Locate Parts and Tools
Service Kit Parts
Power supply
Fan
Fan bracket screws (2) with nuts (2)
Security screw bit
Tools Required
Phillips screwdriver
Driver for security screw bit
Flathead screwdriver
Box knife
Clean, dry cloth
Canned air (multi-purpose duster safe for electronic circuitry)
Electrostatic discharge (ESD) wristband or other ESD protection
Open and Clean Chassis
1. . Turn off player.
2. Disconnect all cables including the power cord.
3. Remove from rack
Movie Player Power Supply and Fan Replacement July 22, 2010
Page 2 of 9
4. Remove rack ears. Set screws aside.
5. Remove the four screws from the back including the security screw using
the security screw bit and set aside.
6. Cut through the warranty sticker with a knife.
Movie Player Power Supply and Fan Replacement July 22, 2010
Page 3 of 9
7. Turn the player so the back of the player faces away.
8. Place both hands on the top of the chassis at the back. Use both the
palms of the hand and fingers to push and unseat the chassis lid. Listen
for the snap. Then remove the lid.
9. Wipe the inside of the chassis lid clean.
10. Use canned air to clean the circuit board. Hold the can at least 6 in. from
the board and blow air out the chassis side vents.
11. Blow canned air across the power supply channel and fan, blowing air out
the rear vent.
Movie Player Power Supply and Fan Replacement July 22, 2010
Page 4 of 9
Remove Power Supply and Fan
1. Attach ESD wristband and clip to any side of the chassis (or provide other
ESD protection while performing these procedures).
2. Remove the power supply output cable assembly from the power supply.
If needed, use a flathead screwdriver to disengage the locking lever to
unplug the cable assembly.
3. Remove the AC inlet connector from the power supply. This connector is
locked in and the board connector must be pushed away for removal.
Movie Player Power Supply and Fan Replacement July 22, 2010
Page 5 of 9
4. Remove the four screws holding the power supply to the chassis and
remove the power supply.
5. Remove the fan power connector from the main board.
6. Remove the fan. Loosen and remove the two screws holding the fan to
the fan bracket. Use a #1 Phillips screwdriver and a 1/4 in. nut driver to
remove both fan mounting screws and nuts.
Screws can be accessed by inserting the screwdriver through the fan vent
on the back of the player.
Movie Player Power Supply and Fan Replacement July 22, 2010
Page 6 of 9
7. Discard fan mounting screws.
Replace Fan and Power Supply
1. Install the new fan. Feed the fan power cable and connector through
channel and attach the fan to the fan bracket using the screws provided
in the service kit.
Note: Be sure the fan label faces toward the back of the chassis.
Movie Player Power Supply and Fan Replacement July 22, 2010
Page 7 of 9
2. Connect the fan power cable to the main board.
3. Install the new power supply. Align the holes on the power supply with the
chassis mount. Replace screws and screw onto the chassis finger tight.
4. Connect the power supply output cable connector.
Movie Player Power Supply and Fan Replacement July 22, 2010
Page 8 of 9
5. Connect the AC inlet connector.
6. Verify that all connectors are completely locked in place and secure.
7. Disconnect ESD wristband if used.
Reattach Chassis Lid
1. Align the chassis lid. The metal piece on the front fits into the notches on
the chassis.
2. Push the lid back in place.
Movie Player Power Supply and Fan Replacement July 22, 2010
Page 9 of 9
3. Replace back screws including security screw.
4. Replace rack ears.
5. Replace power cable and plug into power outlet to verify that the player
powers on.
For additional information, contact Kaleidescape Support.
Send an email message to [email protected].
Call the support line at +1 (650) 625-6160.
Kaleidescape
Support
