KAMEHA KA139 User manual

8x8 HDMI 18Gbps Matrix with
Audio De-embedded
VER 2.1

Thank you for purchasing this product
Surge protection device recommended
Table of Contents
For optimum performance and safety, please read these instructions caref-
ully before connecting, operating or adjusting this product. Please keep this
manual for future reference.
This product contains sensitive electrical components that may be damaged
by electrical spikes, surges, electric shook, lighting strikes, etc. Use of surge
protection systems is highly recommended in order to protect and extend the
life of your equipment.
1. Introduction.........................................................................................
2. Features...............................................................................................
3. Package Contents..............................................................................
4. Specifications......................................................................................
5. Operation Controls and Functions....................................................
5.1. Front Panel..................................................................................
5.2. Rear Panel...................................................................................
6. IR Remote.............................................................................................
7. Web GUI User Guide...........................................................................
8. ASCII control command....................................................................
9. Application Example..........................................................................
10. FAQ.....................................................................................................
1
1
1
2
3
3
5
6
6
12
19
19

1. Introduction
2. Features
3. Package Contents
The 8x8 HDMI Matrix supports the transmission of video (up to 4K2K@60Hz
YUV 4:4:4, 18Gbps, HDCP 2.2) and multi-channel digital audio from 8 HDMI
sources to 8 HDMI displays. Audio de-embedded is supported from 8 HDMI
output ports. Control is via button, IR remote, Web GUI and ASCII command.
☆HDMI 2.0b, HDCP 2.2 and HDCP 1.4 compliant
☆Up to 4K2K@60Hz (YUV 4:4:4) on all HDMI ports
☆Supports pass-through audio up to 7.1 channels of High Definition audio
(LPCM, Dolby TrueHD, and DTS-HD Master Audio)
☆Audio de-embedded is supported via coax port
☆HDR, CEC and smart EDID management supported
☆Control is via on-panel button, IR remote, Web GUI and ASCII command
☆1U rack mounted design with metal enclosure
①1x 8x8 HDMI Matrix
②1x 12V/3A Locking Power Adaptor
③1x IR Remote
④1x Wideband IR Receiver cable
⑤1x RS-232 male to female serial cable
⑥1x User Manual
1/19

4. Specifications
Technical
HDMI Compliance HDMI 2.0b
HDCP Compliance HDCP 2.2 and HDCP 1.4
Video Bandwidth 18Gbps
Up to 4K2K@50/60Hz (YUV 4:4:4), 4K2K@30Hz,
1080p@120Hz, and 1080p 3D@60Hz
Color Depth 8-bit, 10-bit, 12-bit
HDMI Audio
Formats
Connections
Outputs
Mechanical
3.35kg
Input: AC100~240V 50/60Hz, Output: DC12V/3A
(US/EU standards, CE/FCC/UL certified)
26.5W (max)
0°C ~ 40°C / 32°F ~ 104°F
-20°C ~ 60°C / -4°F ~ 140°F
ESD Protection Human-body Model:
±8kV (Air-gap discharge) , ±4kV (Contact discharge)
Power Supply
Dimensions
Weight
Metal Enclosure
Operating
Temperature
Storage
Temperature
Relative Humidity 20~90% RH (non-condensing)
Power
Consumption
Color Black
483mm (W)×253mm (D)×44.5mm (H)
Housing
Video Resolutions
Color Space RGB, YCbCr 4:4:4, YCbCr 4:2:2
LPCM 2/5.1/7.1, Dolby Digital, DTS 5.1, Dolby Digital+,
Dolby TrueHD, DTS-HD Master Audio, Dolby Atmos,
DTS:X
Inputs
8x HDMI Type A [19-pin female]
1x LAN [RJ45, Control]
1x RS-232 [9-pin D-sub, Control]
1x IR EXT [3.5mm Stereo Mini-jack]
8x HDMI Type A [19-pin female]
8x Coaxial Audio [RCA]
Audio Formats PCM2.0, 32K/44.1K/48K/88.2K/96K/192K, 16/20/24bit
2/19

5. Operation Controls and Functions
5.1 Front Panel
4
Number Name Function descriptions
1 OLED display Display system input/output port status, EDID
management and matrix IP address.
2 IR Window
3
IR receiver window, it receives IR remote control
signal to control this device.
12 3 4
Left/Right/Up/
Down/Menu
Buttons
After system power up, the OLED screen default displays
the input and output status of the last power off.
A) On the initial OLED display, you can press the
‘Left’ or ‘Right’ button firstly to select output port,
then press the ‘up’ or ‘down’ button to select the input
port, then press the ‘MENU’ button to confirm this
operation.
B) On the initial OLED display, you can press the ‘Up’
or ‘Down’ button to check each input EDID setting,
press the ‘Menu’ button go back to the initial
OLED display.
C) On the initial OLED display, you can press ‘Menu’
button to operate the following functions by the
combination of these five buttons, press ‘Up’ or
‘Down’ button to select function:
1. Select EDID: Press the ‘Right’ button, then press
the ‘Up’ or ‘Down’ button to select EDID as showed in
the below table. Once you complete EDID selection,
press the ‘Right’ button then press the ‘Left’ or ‘Right’
button to select your EDID to copy to which
input port, press the ‘Right’ button to confirm this
operation.
2. PTP Set: Press the ‘Right’ button to set PTP mode
(point to point, means IN1-OUT A, IN2-OUT B, IN3-
OUT C...).
3/19

3. Save Preset: Press the ‘Right’ button to save
current configuration to preset, press ‘Up’ or ‘Down’
button to select storage location, press the
‘Right’ button to confirm this operation.
4. Recall Preset: Press the ‘Right’ button to recall
previous preset, press ‘Up’ or ‘Down’ button to select
preset you want, press the ‘Right’ button to confirm
this operation.
5. View IP: Press the ‘Right’ button to check IP
address and DHCP status.
6. Select Baud: Press the ‘Right’ button, then press
the ‘Up’ or ‘Down’ button to select baud, press the
‘Right’ button to confirm this operation.
7. Factory Reset: Press the ‘Right’ button to setting
factory reset status, then press the ‘Right’ button to
confirm this operation or the ‘Left’ button to quit this
operation.
The EDID table:
EDID Mode EDID Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
720P 2.0 CH
1080P 2.0 CH
1080P 5.1 CH
1080P 7.1CH
1080I 2.0 CH
1080I 5.1 CH
1080I 7.1CH
3D 2.0 CH
3D 5.1 CH
3D 7.1 CH
4K*2K@30 2.0 CH
4K*2K@30 5.1 CH
4K*2K@30 7.1 CH
4K60_420 2.0CH
4K60_420 5.1CH
4K60_420 7.1CH
4Power and
Power LED
Long press this button to power on/off device. The LED
will illuminate in green when the device is power on
and show in red when this device is standby.
4/19

5.2 Rear Panel
25
26
27
Copy HDMI Out F
Copy HDMI Out G
Copy HDMI Out H
AUDIO OUTPUT
OUTPUT
1234
567
4
Number Name Function descriptions
1 HDMI INPUT Connect to the HDMI input source devices such as
a DVD player or Set-top Box.
2 HDMI OUTPUT Connect to the HDMI output source devices such
as a TV player or monitor.
3 IR EXT
If the front IR sensor of unit is obstructed or the
unit is installed in a closed area out of infrared line
of sight, the IR receiver cable can be inserted to
this IR EXT port to extend IR signal.
4 DC 12V Plug the 12V/3A adapter to AC wall outlet for
power supply.
5CONTROL
LAN: connects to an active Ethernet link by an
RJ-45 cable.
RS-232: Connect to a PC or control system by D-
Sub 9-pin cable to control the matrix with RS-232
commands.
6 AUDIO OUTPUT Connect to audio amplifiers or speakers. The audio
is from extract HDMI output port signal.
7 GND Connect the GND port to the ground.
21
22
23
24
Copy HDMI Out B
Copy HDMI Out C
Copy HDMI Out D
Copy HDMI Out E
17 4K*2K@60 2.0 CH
18
19
20
4K*2K@60 5.1 CH
4K*2K@60 7.1 CH
Copy HDMI Out A
5/19

6. IR Remote
7. Web GUI User Guide
The Matrix can be controlled via Web GUI. You must know current Matrix IP
address. The static IP address is 192.168.1.100. You can get current IP
address via on-panel button. The LAN port of the Matrix connects directly a
PC with an UTP cable. The following is the Web GUI connection diagram.
Please check the following operation instruction.
Input
1 2 3 4
5 6 7 8
Output
5 86 7
All
HDMI Matrix Remote
1 2 3 4
: Power on or set it to standby status.
Input 1/2/3/4/5/6/7/8: Press these button to
select input signal source.
: Press these button to select the last or
the next input signal source.
Output 1/2/3/4/5/6/7/8: Press these button to
select output signal source.
All: Press this button to select all output signal
source simultaneously.
Operating instructions: User need select output
button firstly and then select input button to select
output display corresponding input signal source.
Web GUI connection diagram
LAN
PC
LAN
The Matrix gets IP address via on-panel button. On the initial OLED display,
you can press “Menu” button to enter function page. Then press “Up” or
“Down” button to select function. When select the “View IP” function, then
press the “Right” button to check current IP address and DHCP status. At
this moment, you can get current IP address.
LAN
6/19

Double click Internet Protocol Version 4 (TCP/IPv4)
Step 1: The LAN port connects directly PC with an UTP cable.
Step 2: On the PC, go to Control Panel > Network and Internet > Network
Connections > Local Area Connections, right click on it, choose Propertiers.
7/19

1 200
Choose “Use the following IP address”, for instance, input 192.168.1.200 as
IP address, 255.255.255.0 as Subnet mask, and then click on OK, click on
OK again.
Note: The IP address of the computer and matrix should be in the same
network segment. As the matrix's IP address is 192.168.1.100, the computer's
IP should be 192.168.1.X (X contains 1~255 except 100).
Step 3. Input the IP address from front panel into a browser on the PC to enter
Web GUI page, The pages like below.
8/19

The Web GUI likes below:
2
1
34 5 6
①Click this button to check current the Matrix connection status.
②Display currently the Matrix input and output port status. The “yes”
have connected input or output source and “no” represent not connection.
③Power switch. The Matrix will work when open this switch. Otherwise, the
Matrix will standby.
④Beep switch. Open this switch, press the Matrix on-panel button will have
voice. Close this switch, it will mute.
⑤Click this button will reboot device.
⑥Click this button will set it to factory reset.
General page
9/19

①You need click green area and then choose one input source to the
OUTPUT A port. (The others OUTPUT ports have similar to function about Tab ①.)
1
2
3
4
①Select EDID mode to input source, then click “Set” button.
②Copy EDID from output display to input source, then click “Set” button.
③Open EDID file to input source.
④Display the input source EDID mode status.
Matrix page
EDID page
1
10/19

Network page
21
3
①Network Configuration
◆In DHCP open status:
DHCP switch: Obtian automatically the network configuration information,
including IP address, Subnet, Gateway and MAC.
◆In DHCP close status:
DHCP switch: If the DHCP switch has been closed, user can set IP, Subnet,
Gateway and Mac address. In this moment, click the “Save Changes” button
to save current status information. (Note: If user have set a new IP address
and click the “Save Changes” button. At this moment, user have changed
the IP address.)
Net Status button: Click this button will refresh currently network configuration
information to display in Status Log.
②Status Log: Display the Net configuration information.
③Clear button: Clear the Status Log information.
11/19

Upgrade page
①Open upgrade file, then click the “Upgrade” button.
The product also supports ASCII control. You need to a RS-232 male head
with DB9 transfer USB male head serial cable. The RS-232 head of the serial
cable is connected the RS-232 control port with DB 9 at the rear of the Matrix,
and the USB head of the serial cable is connected a PC. Open any of a Serial
Command tool on PC such as “Docklight” to send command to control the
Matrix.
The fellowing is shown RS-232 pin’s definition and connection way.
1 2 3 4 5
6 7 8 9
9-Pin male DIN interface
8. ASCII control command
12/19

PIN SIGNAL DESCRIPTION
1 DCD Data Carry Detect
2 SIN Serial In or Receiver Data
3 SOUT Serial Out or Transmit Data
4 DTR Data Terminal Ready
5 GND Ground
6 DSR Data Set Ready
7RTS Request To Send
8 CTS Clear To Send
9 RI Ring Indicate
Pin’s definition
Double click the “Docklight” shortcut icon. Please see the following picture 1.
Picture 1
↑
13/19

You will see the following page.
Click the “COM” area, there will be a “Project Settings” page. Choose the
COM port to connect the software, and you need to setting the Baud Rate,
Data Bits, Parity,Stop Bits and then click the “OK” button. Please see the
following page.
1
5
14/19

Double click the “label 1” blank area. You will see the following page. At
“label 2”, you can explain sequence definition. At “label 3”, you need to choose
the sequence mode. At “label 4”, you can input the RS-232 command of the
product. Then click the “OK” button.
2
3
4
Finally, you need to click “label 5” button to send the command.
15/19

The ASCII list about the product is shown as below.
ASCII Commands
Serial port protocol: Baud rate(default): 19200 Data bits: 8 Stop bits: 1 Check bit: 0
RS-232 Command Function description Feedback
s x av y! AV x -> y
s x all! Switch x channel input to all channel output x to all
r all out! Get the corresponding switch state between all
output port and the input port AV 1 -> 1, AV 2 -> 2...
r out 1! Get the corresponding switch state between the
x output port and the input port AV x -> x
s ptp! one to one between input and output channels ptp
r link in x! Get the connection status of the x input port
r link out x! Get the connection status of the x output port
r link in all! Get the connection status of all input port
Get the connection status of all input port
s x off! Turn off the x output channel out x off
s x on! Turn on the x output channel out x on
s all off! Turn off all the output channel all out off
s all on! Turn on all the output channel all out on
s edid x c y! Copy the display EDID on the x output port to the
y input port
copy EDID from output x to
input y
s edid x d y! Copy the built-in EDID number y to the x input port use default edid y to input x
s edid all c y! Copy the display EDID on the x output port to all
inputs
copy edid from output y to all
inputs
s edid all d y! Copy the built-in EDID number y to all input ports use default edid y to all input
s edid default! Restore the default EDID (1080P 2) to each input
port edid default
r edid x! Get the Edid state of the x input port
r edid all! Query the EDID status of all ports
s x hdcp 2.2! Force opening hdcp of the x output port out x hdcp 2.2
HDMI INx: connect
HDMI OUTx: disconnect
HDMI INx: connect/disconnect
r link out all! HDMI OUTx: connect/disconnect
IN1: 1080p,Stereo Audio 2.0
IN1: 1080p,Stereo Audio 2.0
s x hdcp 1.4! Force opening hdcp of the x output port out x hdcp 1.4
s x hdcp off! Force shutdown hdcp of the x output port out x hdcp off
s x hdcp auto! Automatic management hdcp of x output port out x hdcp auto
Switch x channel input to y channel output
16/19

s all hdcp off! Force shutdown hdcp of the all output port all out hdcp off
s all hdcp auto! Automatic management hdcp of all output port all out hdcp auto
r hdcp in x! Get the Hdcp state of the x input port a hdcp in
r hdcp out x! Get the Hdcp state of the x output port a hdcp out
r hdcp all in! Query all input port HDCP status a hdcp in all
r hdcp all out! Query all output port HDCP status a hdcp out all
s beep on! Open buzzer function beep on
s beep off! Cancel buzzer function beep off
r beep! Get the switch state of the buzzer a beep on
s lock on! Panel lock lock on
s lock off! Panel unlock lock off
r lock! Get the status of the panel key lock a lock on
s power on! Machine boot power on
s power off! Machine shutdown power off
r power! Query power state a power on
s rboot! Machine reboot rboot
s factory reset! Restore factory settings
r type! Query matrix model a HDM-B88
r version! Query software version a aa.bb-aa.bb-aa.bb
r status! Query the status of the entire machine
s dhcp off! Set up network module using static IP
s dhcp on! Set up network modules using dynamic IP
r dhcp! Get the Dhcp status of the network module a ip mode DHCP
ip mode DHCP
s ip addr a.b.c.d!
Set the IP address of the network board a.b.c.d
s mac addr a-b
-c-d-e-f！Set the MAC address of the network board a-b-c-d-e-f
s subnet a.b.c.d!
s port 8000! Set control port at 8000 8000
factory reset
a aa.bb-aa.bb-aa.bb.cc.dd
ip mode static
Setting subnet mask of network module a.b.c.d
s gateway a.b.c.d! Set up network module gateway a.b.c.d
RS-232 Command Function description Feedback
17/19

s network enable!
When configuring network modules, execute all the
commands you need to configure first and then
execute this command to reboot network modules
r ip addr! Get the IP address of the network board a a.b.c.d <CR>
r mac addr! Get the MAC address of the network board a a-b-c-d-e-f <CR>
r subnet！Get the subnet mask of the network board a a.b.c.d <CR>
r gateway! Get the gateway of the network board a a.b.c.d <CR>
r port! Get network port number a 8000 <CR>
s net name ****! Set the name of the network module *******
r net name! Get the name of the network module a ******* <CR>
RS-232 Command Function description Feedback
Note: In this table, you can send “RS-232 Commands” to control the product in any
serial command tool. The “Function description” will explain function about the command.
The “Feedback” will display whether the command sends success and feedback the
information you need to.
18/19