Kanrich 915 User manual

915 2-wire
video doorphone
system
User Manual
Villa Type

The Cable Specifications
of 915 2-wire System
with shield(aluminum foil)
anti-interference
CAT 5e STP
Quality is the best and the distance
up to 100M is still good ,with power line
together without signal/video interference.
Please pay much attention , there are 4 pairs in CAT5e
, just use 2 pairs of them , other 2 pairs never to use it .
P1
completed
soldering
no soldering
To solder 2 cores connection point ,
this way can prevent single core
is broken and make the wire
connection
is stable .

BAL (never touch)
915C10AL Color Aluminum Camera
Inside View
Mic.
White LED
CCD
SPK.
Resident 1 Call Button
Resident 2 Call Button
SW1 open door time(No.1)
←15 sec. 2 sec.→
MIC. Gain
SPK. Gain
Clockwise +
anticlockwise ─
Specifications :
Working Voltage : DC 15V from PH-915P
Current Consumption: Standby 60mA
Working 250mA
CCD: Color Sony 1/3” Board Camera
Resolution: 510(H) x 492(V)
Signal Noise Rate : More than 48db
Picture Pixels: 270,000 Pixels
Ilumination : 4 white LEDs
Communication Interface :
the modulated carrier wave signal
Installation Way : Flush Mounting Type or
Surface Mounting Type
Front Material : Aluminum Panel
Dimensions : 200(H)/120(W)/55(H) mm
Weights: 570 gs
Measurement: 0.07 cuft
Accessories: 1 Terminal connector *
screw bag *1
Terminals
In/Out main line + FGND main line 一
D1(Door NO)open door contact
D2(Door COM)open door contact
A1(Aux NO)open door contact
PT (for door lock)
GND
Door Lock
Power for
door lock
(The power of door lock must be an independent power,
door phone power can’t share power with door lock.)
A2(Aux NO)open door contact
Video Out
GND Ground wire
1 2 3 4 5 6 7 8 9 10
+
-
P12
2011 Sep.
The sensor of door unlock

Flush Pre-box for model "AL" Camera
175/105/60mm
Surface Pre-box for model "AL" Camera
210/125/60mm

Color
CCD
Mic.
White
LED
Call
Button
SPK.
SVR1 SVR2
2 sec.
915CAL Aluminum Camera with CCD
915CALM Aluminum Camera & Mifare Card Reader
The sensitive
area of card
reader
Inside View
SW1
open door time set
SVR1 MIC. Gain
SVR2 SPK. Gain
Clockwise
anticlockwise
15 sec.
+
-
In/Out System
In/Out System
N.O(Door N.O) normal open
COM(Door COM.)normal open
N.C(Door N.C)normal close
PT(PT+) door lock PT +
-
Connect this N.C.
Point to open door.
1N4007
Rear View
Specifications :
Working Voltage : DC 15V from PH-915P
Current Consumption: Standby 110mA
Working 320mA
CCD: Color Sony 1/3” Board Camera
Resolution: 510(H) x 492(V)
Signal Noise Rate : More than 48db
Picture Pixels: 270,000 Pixels
Ilumination : 2 white LEDs
Communication Interface :
Installation Way : Flush Mounting Type or
Surface Mounting Type
Front Material : Aluminum Panel
Dimensions : 200(H)/120(W)/55(H) mm
Weights: 570 gs
Measurement: 0.07 cuft
Accessories: 2-pin white connector*1
6-pin white connector*1
N4007 *1 diode
Screw bag*1
Red
Black
Brown
Blue
Yellow
Green
Connector Explanation
Black Blue
External connect
open door switch
Protect Purpose
Door
Lock
Power for
door lock
(DC18V)
(The power of door lock must be an independent
power, door phone power can’t share power with
door lock.)
If door lock is close, connect this point
to open door.
The sensor of
door unlock
Please connect an external power
to Mifare card reader
P14-1

Mifare Card
The user guide of Card Reader For CALM - Villa Type
To add new cards:
1. To add cards:
By Master REG (The Master Card for registering a new card or cards)
Steps: To swipe Master REG one time--beep--green light flashing
--swipe new card(or cards)--beep in twice
Successfully register new card (or cards), if you want to
stop adding cards,
just swipe Master REG one time --beep-- --finish.green light off
2. To cards: delete
By Master DEL (The Master Card for deleting a new card or cards)
Steps: To swipe Master DEL one time--beep--red light flashing
--swipe the card(or cards) want to be deleted--beep in twice
Successfully delete a card (or cards), if you want to
stop deleting cards, just swipe Master DEL one time
--beep-- --finish.red light off
Please add "00" before the 8-digit number to be 10-digit.
Mifare Key Tag
P14-2

Accessories
1. 7-pin connector 1
2. Bracket 1
3. Screw bag 1
REAR
VIEW
In/Out system line + FGND system line 一
External SPK
GND
Video Out
Bell
GND
Monitor
External bell switch
To connect all monitors
in the same house.
915M35 3.5” Handsfree Color Monitor
Handsfree Talking / Monitoring Button
: itHandsfree Talking button Press for getting a call and talking .
After talking press it again for finish.
Monitoring button : itPress to start monitor screen and monitor door camera
situation and also to talk with camera ,press for finish. it again
The talking time limitation is 180 sec.
.
“In Use" indicator / Intercom call Indicator(Red):
The red LED constantly on, it means one of residents is using this doorphone system,
please wait this resident finishing talking then to use it .
This indicator is flashing , it means intercom function is started.Intercom Indicator :
Power Indicator : The Blue LED constantly lights on.
SPK.
Mic.
Color
Code setting button/Main monitor & Sub monitor setting button
Code setting button : When doorphone system is standby and press
" + ", you will hear "Du" on 915M35 and on camera ,too.
Please enter "monitor code"on camera immediately , 915M35 will get this call
and send "Ding-Dong" , it means a successful code setting .
: Hold this button 8 sec. at least , Main monitor-Sub monitor setting button
you will hear a high-pitch “Du", it means to set main monitor successfully.
Then, hold this button 8 sec. at least , you will hear a deep "Du" , it means to
set sub monitor successfully.
PS. One apartment only can set one main monitor, if you set 2 main monitors
in one apartment , camera can't call monitor normally ,the doorphone system
will happen problem ,camera can't make a call to this apartment .
Intercom Button/ NO Contact Point
Intercom Press this button to intercom and talk with other monitors in
this apartment .
When monitor screen is started , press this button andNO Contact Point
drive this contact point in camera then to start other devices.
Door Release Button / Code setting button
Door Release Press " " this button for opening door.
: When doorphone system is standby and pressCode setting button
" + ", you will hear "Du" on 915M35 and on camera ,too.
Please enter "monitor code"on camera immediately , 915M35 will get this call
and send "Ding-Dong" , it means a successful code setting .
Brightness
Calling Tone Adj.
Door Status Indicator : The red LED constantly lights on , it means the door is open, the red LED
lights off , it means the door is close .
Specifications :
Working Voltage : DC 15V from 915P
Current Consumption: Standby 40mA
Working 300mA
Resolution: color 3.5” 320(H) x 240(V)
Communication Interface :
the modulated carrier wave signal
Installation Way : Surface Mounting Type
Front Material : ABS
Dimensions : 189.5(H)/129.5(W)/30(H) mm
Weights: 310 gs
Measurement: 0.3 cuft P15
2011 Sep.
Dummy Load
ON ↑
OFF↓
1 2
N0.1 No Function

+
915Mi 4" Handsfree video monitor
TFT screen
adjustment
Code setting button/
Indicator(system in use)
video dummy
Door Release 2
Door Release 1/
Resident Code setting button
/ Door Status Indicator
ringing tone
adjustment
Handsfree Talking /
Monitoring
Buttons/Indicators
Resident Code setting button
When doorphone system is standby and press " + ", you will hear "Du" on monitor
and on camera ,too. Please enter "monitor code" on camera immediately , monitor will get
this call and send "Ding-Dong" , it means a successful code setting .
"in use" indicator
The red LED constantly on, it means one of residents is using this doorphone system,
please wait this resident finishing talking then to use it .If you find this indicator is flashing
in operation ,please press " " twice , let system return to "standby" status .
Door Release 2
When monitor screen is started , press " " for opening another door lock of another door.
Door Release 1/Code setting button
Press for opening door lock of door no. 1 .
Door Status Indicator
The red LED constantly on , it means the door no.1 is open, the red LED lights off ,it means
the door is close .
Handsfree Talking
Press for getting a call and talking , press one more time for off line.
The talking time limitation is 180 sec. If after talking , the resident forgot to press for
finishing talking, the system will be off line automatically 180 sec. later .
Monitoring
Press to start monitor screen and monitor door camera situation and also to talk with
camera , press one more time for finish.
TFT screen adjustment
Up : TFT screen adjustment buttons---CONTRAST / BRIGHTNESS / COLOR / RESET / EXIT
Middle : adjustment
Down : adjustment
+
--
P18
2011 Sep.

Switch
Video Dummy
swich up ----OFF
switch down ---ON
Monitor
rear view
12 3 4 5 6 7
12 3 4 5 6 7
915Mi 4" Handsfree video monitor
Ringing Tone Adjustment
Up --- volume increase
Middle --- volume middle
Down --- volume down
In/Out
FGND
ESPK
Video Out
Bell
GND
Speaker
ground
external door
bell switch
GND ground
external
SPK.
system wire
system wire
+
一
Terminals
Monitor code setting steps :
1. When doorphone system is standby and press " " + " ".
2. You will hear "Du" on monitor and on camera ,too.
3. Please enter "monitor code" on camera immediately , monitor will get this call
and send "Ding-Dong" as well as the screen is started at the same time,
press " " to close screen. It's a successful code setting .
Specifications
Working Voltage: DC15V from 915P
Current Consumption :
Stand-by 40mA, Working 300mA
Resolution: Color 4” 960(H)x234(V)
Communicating Interface:
the modulated carrier wave signal
Installation way: Surface mounting type
Material: ABS heat-resistant plastic
Dimensions: (H)140mm/(W)170mm/(D)35mm
Weights : 300gs
Measurement: 0.2 cuft
Accessories
1. Green terminal connector 1
2. Monitor Bracket 1
3. Screw Bag 1
P19
2011 Sep.

Call 915CC/Code setting button/Main monitor & Sub monitor setting button
Handsfree Talking / Monitoring Button
: After talking press again for finish. Handsfree Talking button Press for getting a call and talking .
Monitoring button :Press to start monitor screen and monitor door camera situation and also to talk
with camera ,press for finish. The talking time limitation is 180 sec. again
Intercom Button/ N.O. Contact Point
Intercom Press this button to intercom and talk with other monitors in this apartment .
When monitor screen is started , press this button andN.O. Contact Point
drive this contact point in camera then to start other devices.
Door Release Button / Code setting button
Door Release Press “ " door.to open the
: When doorphone system is standby and press " + ",Code setting button this button code setting button
you will hear "Du" on 915M and on camera ,too. Please enter "monitor code"on camera immediately , 7
915M will get this call and send "Ding-Dong" , it means a successful code setting .7
In/Out System Line + FGND System Line 一
ESPK
External SPK.
GND
Video Out
Bell
Monitor
External door
bell switch
For Intercom
function
DC
12V
+DC12V
REAR VIEW
Color Adj. Knob
Brightness Adj. Knob
Calling Tone Volume Knob
Side View
↑ +
↓ -
Power Indicator Power Indicator - green - power on
Door Status Indicator(Red)
The red LED constantly lights on , it means the main door is
open, the red LED lights off ,it means the main door is close .
mic.
External power
for LCD screen
in apartment project.
915M7 7” Handsfree video monitor
spk.
Call 915CC : Press “ " + " " to call control center and talk to the guard ; press “ “ again for finishing talk.
Code setting button : When doorphone system is standby and press " + ",you will hear
"Du" on 915M7 and on camera ,too. Please enter "monitor code"on camera immediately , 915M7 will get this
call and send "Ding-Dong" , it means a successful code setting .
: Hold this button 8 sec. at least ,you will hear a high-pitch “Du",Main monitor-Sub monitor setting button
it means to set main monitor successfully.Then, hold this button 8 sec. at least , you will hear a deep "Du",it
means to set sub monitor successfully.
PS. One apartment only can set one main monitor, if you set 2 main monitors in one apartment ,camera can't
call monitor normally ,the doorphone system will happen problem ,camera can't make a call to this apartment .
Specifications
Working Voltage: DC15V from 915P
Current Consumption : Stand-by 40mA,
Working 170mA(the power of LCD screen is
from external DC12V)
Working 450mA(the power of LCD screen is
from main line of doorphone)
Resolution: Color 7” 800RGB(H)x480(V)
Installation way: Surface mounting type
Material: Aluminum & ABS heat-resistant
Plastic
Dimensions: (H)150mm/(W)235mm/(D)28mm
Weights : 700gs
Measurement: 0.35 cuft
Accessories
1. 7-pin connector 1
2. Monitor Bracket 1
3. Screw Bag 1
P20
2011 Sep.
Dummy Load
ON
OFF
LCD screen power setting
Please pay attention to
the direction of short pin.
The LCD screen power is
from the main line ( for single
house project)
The LCD screen power is
from external DC12V power
(for apartment project)
"in use" indicator / Intercom Indicator (Red)
This indicator is on - It means one of residents is using ,
please wait this resident finishing talking then to use .
Green/Red mutual flashing, it means intercom function is started.

Dummy
Load
ON
OFF
In/Out System Line + FGND System Line 一
ESPK External SPK.
GND
Video Out
Bell
External door
bell switch
DC
12V
+DC12V
rear view
External power
GND
Monitor
SD
915M7b 7” Touch Pad Handsfree video monitor
Clock when the screen on and time is display, access to toolbar and choose for adjusting time.
"in use" indicator / Intercom Indicator (Red)
The red light on - It means one of residents is using ,please wait
this resident finishing talking then to use .
The red light flashing, it means intercom function is started.
Door Status Indicator / picture indicator(Red)
The red light on constantly, it means the main door is
open, the red light off, it means the main door is close .
The red light flashing, it means the new picture coming.
Touchpad
In standby status,only the first key(top one) has indicator, just touch
it on touch area, all 5 touch keys with 5 indicators on and screen on
immediately. Please touch the touch key according to icon(on the
left view of touchpad).
Calling Tone
Volume Knob
Code setting : When system is standby and touch " + ",you will hear "Du" on 915M7b and on camera ,too.
Please enter "monitor code"on camera immediately , 915M7b will get this call and send "Ding-Dong" , it means a successful
code setting .
: Keep touching 8 sec. at least ,you will hear a high-pitch “Du", it means to set main Main monitor-Sub monitor setting
monitor successfully.Then, keep touching 8 sec. at least , you will hear a deep "Du",it means to set sub monitor successfully.
PS. One apartment only can set one main monitor, if you set 2 main monitors in one apartment ,camera can't call monitor(You
can hear “Ding-Dong” on monitor but no video).
The same problem will be happened when the system is no “main monitor” setting .
Code setting/Main monitor & Sub monitor setting
Monitor on or operate something then return to “Home Screen”, within 10 sec. without next operation, the screen
will be off and return to standby status. If you need further information, please access to , touch and get
more informaton(next pages) by touch and .
Adjust clock : The clock is on the upper left side , access to and touch for adjusting time .
Adjust brightness : Access to and touch for adjusting brightness .
Check pictures or change picture quantity : Access to , touch for choosing 0/1/3 .
PS.1. The period of taking picture, all buttons are locked temporarily till finish taking picture.
2. Automatically take picture set "3" - "go out" mode - one call , take 3 pictures ;
set "1" - "at home" mode - one call, take 1 picture ;
set "0" - "no picture" mode , no tate picture.
3. Due to the period of taking picture, all buttons are locked temporarily. When camera call monitor and start to
take a picture, you have to wait till finish "take a picture" then talk with monitor . The waiting time is about
12 sec. from calling to finish taking a picture.
Talking Volume Knob
Specifications
Working Voltage: DC15V from 915P
Current Consumption : Stand-by 200mA
Working 600mA
Resolution: Color 7” 800RGB(H)x480(V)
Installation way: Surface mounting type
Material: ABS heat-resistant plastic
Dimensions: (H)155mm/(W)256mm/(D)27mm
Weights : 500gs
Measurement: 0.35 cuft
For Intercom
function
Accessories
1. 6-pin connector 1
2. 2-pin connector 1
3. Monitor Bracket 1
4. Screw Bag 1
SPK.
MIC.
2012/ 12/ 12 12:12:12
P21

Inter-Call Inter-Call
OFF
915M7b 2012 10月
Home
Screen Handsfree
Talking On
Line
Off
Line
Open Door 2
Open Door 1
shooting in
manual mode
screen stop about
3 sec. then return
Home
Screen
Intercom Intercom
Home
Screen
Call
control center
Off
Line
P22

SD 3
2012/ 12/ 12 12:12:12
2012/ 10/ 10 10:10:10
200
SD
2012/ 12/ 12 12:12:12
SD 2012/ 12/ 12 12:12:12
Brightness : 10
SD 2012/ 12/ 12 12:12:12
Mode No. :PH915M7B
Power dissipation: DC12V/0.6V
Info
Home
Screen
Forward
Picture
Picture Q'ty
0/1/3
different choice
Rearward
Picture Time
Home
Screen
Time
Adjustment
Choice
Plus
Minus
Home
Screen
Plus
Minus
Brightness
Adjustment
Home
Screen
User
Guide
Rewind
Forward
the page of user guide
PS. "0" no take a picture /
"1" one call, take one picture/
"3" one call, take 3 pictures
P23

Door Release -1 / Resident Code Setting
1. Door Release - 1
When a calling is from camera, press this button and pick up the handset to open the 1st door.
2.Resident Code Setting
915M3 , When doorphone system is standby and press " + ", you will hear "Du" on and on camera too.
Please enter " code" on camera immediatel will get this call and send "Ding-Dong" , it means resident y, 915M3
a successful code setting .
JP1
T3
UP
6 5 4 3 2 1
Inside View
of Base
PCB
Dummy Load Switch
Set “ON”
6 5 4 3 2 1
DUMMY
←ON OFF→
In/Out Main Line +
FGND Main Line 一
GND Ground Wire
Bell External Door Bell Switch
(Intercom)
Button Switch
No Function
915M3 Audio Handset
Resident Code Setting / Main Handset & Sub-Handset Setting
1. Resident Code Setting
915M3 , When doorphone system is standby and press " + ", you will hear "Du" on and on camera too.
Please enter " code" on camera immediatel will get this call and send "Ding-Dong" , it means resident y, 915M3
a successful code setting .
2. Main Handset or Sub-Handset Setting
Press this button 8 sec. at least and you will hear a high-pitched “Du”, this handset is set as main handset .
Press this button 8 sec. at least and you will hear a low-pitched “Du”, this handset is set as sub-handset .
To identify the “Du” is high-pitched or “low-pitched” as main or sub handset.
If there are 2 monitors(915M) or “monitor(915M) + audio handset” in one house, it is necessary to set main monitor
and sub-monitor(handset) because one house only allow one main monitor, other monitors(handsets)
are sub-monitors(handsets).
Intercom / Door Release - 2
1. Intercom
Pick up the handset and press this button and talk with another monitor(or handset),
the talking time is 3 min. Hang up the handset and finish talking.
2. Door Release - 2
When a calling is from camera, pick up the handset and press this button to open the 2nd door .
Handset
ick up the handset and talk with camera or other monitors hen you hear the ringing tone, the talP king time limitation is 180 sec. w
When you are talking with camera, an intercom call coming, please hang up the handset first then pick up the handset again
for getting this intercom call. Rear View of Front Cover
Power Indicator
On - Green
In Use / Intercom Indicator
On - Red :
System in using, after Led off then to use.
Flashing - Red :
Intercom in using, after Led off then to use.
Door Status Indicator
On - Red Door is Open
No Function
Connect to other monitors(Handsets) in the same house.
Specifications
Working Voltage:
DC15V from 915P
Current Consumption :
Stand-by 40mA, Working 150mA
Communicating Interface:
the modulated carrier wave signal
Installation way: Surface mounting type
Material: ABS heat-resistant plastic
Dimensions: (H)206mm/(W)92mm/(D)58mm
Weights : 400gs
Measurement: 0.5 cuft
P24
2011 Sep.

SPK.
Mic.
VR2
VR3
1 2 3 4 5 6
In/Out +
FGND 一
GND
(intercom)
Bell external bell switch
switch
useless
EXSPK external SPK.
Connect to monitor to monitor
when one apartment(or house)
has 2 monitors(or handsfree audio).
1 2 3 4 5 6
S1
S1 - Dummy Load
ON
OFF
Terminals
VR2
Calling Tone Adj.
VR3
External SPK. Volume Adj.
- +
- +
915Mg Audio Handset
Power
Indicator
Code setting button/Main monitor & Sub monitor setting button
Code setting button : When doorphone system is standby and press
" + ", you will hear "Du" on 915Mg and on camera ,too.
Please enter "915Mg code"on camera immediately , 915Mg will get this call
and send "Ding-Dong" , it means a successful code setting .
: Hold “ “ 8 sec. at least ,you will Main monitor-Sub monitor setting button
hear a high-pitch “Du", it means to set main monitor successfully.
Then, hold this button 8 sec. at least , you will hear a deep "Du" , it means to
set sub monitor successfully.
PS. One apartment only can set one main monitor, if you set 2 main monitors
in one apartment , camera can't call monitor normally ,the doorphone system
will happen problem ,camera can't make a call to this apartment .
Intercom Button/ NO Contact Point
Intercom Press this button to intercom and talk with other monitors in
this apartment .
When monitor screen is started , press this button andNO Contact Point
drive this contact point in camera then to start other devices.
Door Release Button / Code setting button
Door Release Press " " this button for opening door.
: When doorphone system is standby and pressCode setting button
" + ", you will hear "Du" on 915M35 and on camera ,too.
Please enter "monitor code"on camera immediately , 915M35 will get this call
and send "Ding-Dong" , it means a successful code setting .
Handsfree Talking Button
: itHandsfree Talking button Press for getting a call and talking .
After talking press it again for finish.
Door Status Indicator : The red LED constantly lights on , it means the door is open, the red LED lights off ,
it means the door is close .
“In Use"indicator / Intercom call Indicator(Red):
The red LED constantly on, it means one of residents is using this doorphone system,please wait this resident
finishing talking then to use it .
This indicator is flashing , it means intercom function is started.Intercom Indicator :
Specifications
Working Voltage: DC15V from 915P
Current Consumption :
Stand-by 40mA, Working 150mA
Communicating Interface:
the modulated carrier wave signal
Installation way: Surface mounting type
Material: ABS heat-resistant plastic
Dimensions: (H)210mm/(W)94mm/(D)40mm
Weights : 300gs
Measurement: 0.08 cuft
Rear
View
P25
2011 Sep.

Fuse
AC 250V
1A
Power Indicator
Power In
AC 100-240V
47- 63HZ
In / Out System Main Line +
FGND System Main Line 
915P
915P Power Supply
P27
2011 Sep.
Power Output
DC 15V /1500mA

KANRICH
KANRICH
2 wires video doorphone system
915
915C10AL Camera
1 2 3 4 5 6 7 8 9 10
In/Out +
FGND 一
D1(Door lock N.O.)
D2(Door lock COM)
A1(Aux N.O.)
PT (door lock PT)
GND
A2(Aux COM)
Video Out
GND
Door lock
door lock
power
+
-
door
open
signal
feedback
System wires
independent power
Inner side
BAL ( )do not adjust. MIC gain SPK gain
SW1 door open time(D1 D2)
15 sec. 2 sec.← →
clockwise+
-
counterclockwise

Monitor
Dummy Load
ON
OFF
Rear View
Default is ON
MIC
KANRICH
2 wires video doorphone system
915
915M7
7" Handsfree Monitor
In/Out +
FGND 一
System wires
GND
Extra . SPK
Video Out
Bell extra door bell
LCD screen power setting
Please pay attention to
the direction of short pin.
The LCD screen power is
from the main line ( for single
house project),this is default.
connect to other monitors within one house
(intercom connection)

915P
KANRICH
1 2 3 4 5 6 7 8 9 10
AC
230V
Dummy
Load
ON
Monitor
Cat.5e
Cable
Cat.5e
Cable
2
2
2
2
MIC
KANRICH
2 wires video doorphone system
915
100M
blue/blue white
orange/orange white
door open signal
feedback
Door lock
door lock
power
anothert power for this door lock
+
-
orange/
orange white
blue/
blue white
Connected Cable :Cat.5e
1 Camera and 1 Monitor

KANRICH
1 2 3 4 5 6 7 8 9 10
AC
230V
Dummy
Load
OFF
Monitor
Cat.5e
Cable
Cat.5e
Cable
2
2
2
2
Dummy
Load
Monitor
ON
Cat.5e
Cable
2
2
MIC
MIC
KANRICH
2 wires video doorphone system
915
blue/blue white
orange/orange white
door
open
signal
feedback Door lock
door lock
power
anothert power for this door lock
+
-
orange/orange white
blue/
blue white
blue/
blue white
orange/ orange white
Connected Cable :Cat.5e
PS : 1. When you connect 2 monitors at least ,
please set one of monitors to be main monitor(this is default),
other monitor(monitors) is(are) set to be sub-monitor.
2. How to set main monitor and sub-monitor ?
Hold this button " " + " " 8 sec. at least ,you will hear
a high-pitch “Du",it meansto set main monitor successfully.
Then, hold this button 8 sec. at least ,you will hear
a "low &deep "Du", it means to set sub monitor successfully.
PS. One apartment only can set one main monitor,
if you set 2 main monitors in one apartment ,
camera can't call monitor normally ,the doorphone
system will happen problem ,camera can't make
a call to this apartment .
1 Camera and 2 Monitors
915P
Intercom function :
915M7 — Please connect terminal #7 between monitor and monitor.
915M35/Mi/M7b/Mg/M3 — Please connect terminal #6 between
monitor and monitor .
100M
915C10AL
915M7
915M7