Kaon AR1031 User manual

Set up AR1031 with the KAON App
Wi-Fi Mesh Extender
AR1031
Quick Installation Guide
Step 2. Launch the app. Select AR1031 from the device list.
Step 3. Connect your home gateway to AR1031
Follow the step-by-step instructions on the App to connect
your home gateway to the AR1031 unit.
Step 4. Scan QR code printed on a label on the back of the
AR1031 to connect your smartphone to the AR1031.
Step 5. Enter your login information printed on a label on the
bottom of the AR1031 and tap Login. You can see the dashboard
of the app after you successfully set up your Wi-Fi network.
Step 6. Add AR1031(s) to an existing Wi-Fi Network
If you have more than one AR1031 unit, tap icon on the
top right hand corner of the dashboard to add additional
AR1031(s) one by one. After successfully scan its QR code, tap
Add new AR1031 to create a mesh network.
Step 1. Download the KAON WiFi App Step 7. Customize the network name and password
Tap icon on the top right hand corner of the dashboard,
and select the Wi-Fi settings to create your own network name
(SSID) and password.
Note If your device disconnects from the Wi-Fi network,
view the available Wi-Fi network and then choose
the new network name (SSID) and enter the new
password.
Scan the unique QR code below, or go to Google Play or the Apple
App Store to download the KAON WiFi app. Install the app on a
compatible iPhone or Android smartphone.
<FCC User manual Statements>
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
FCC Part 15.105 statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Part 15.21 statement
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.
RF Exposure Statement (MPE)
The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is
maintained between the radiator (antenna) and all persons at all times. This device must not
be co-located or operating in conjunction with any other antenna or transmitter.

Set up AR1031 without the AppAR1031 overview
➊LED (2.4G, 5G, ETH, MESH, Power)
➋WPS button
➌Factory reset button
➍Ethernet port
➎Power connector
�
LED colors Package contens
The light on the front side of your AR1031 gives you
information about the AR1031’s operation.
Note The MESH LED on the front of the rst AR1031 unit
indicates blue, whereas the MESH LED on the front of
additional AR1031 unit(s) indicates green.
Blinking Blue / Green on MESH LED
The AR1031s are starting up to create mesh networking.
Solid Blue / Green on MESH LED
Mesh network is created successfully and working great.
Solid Yellow on either 2.4GHz or 5GHz LED
The AR1031 is too far from another AR1031.
a.
b.
c.
Step 1. Set up your rst AR1031
Plug AR1031 into a power outlet near to your home
gateway.
Use the included Ethernet cable to connect your home gateway
to the Ethernet port on the AR1031, and then wait 3 minutes
until the MESH LED lights blue to indicate it is completely set up.
a.
b.
Step 3. Access the web-based setup page
Note The Power LED on the front of the extender lights green to
indicate that it’s powered on and ready for setup.
Step 2. Add AR1031(s) to an existing Wi-Fi network
Place additional AR1031(s) at a distance of around three
meters from the working AR1031 connected to your home
gateway.
a.
Note You’ll get the best signal when it is in an open space like
on a shelf or a table.
Plug your additional AR1031(s) into a power outlet.b.
In a few minutes, all AR1031(s) will start to connect each
other automatically to form a mesh network, and in the
meantime, the MESH LEDs on the front of all AR1031s will
c.
Wait for the MESH LED to turn a solid light on all AR1031s,
which indicate that the mesh network is successfully
created in your place.
d.
Note Please press a WPS button on the working AR1031
connected to your home gateway. for 3 seconds within 10
minutes after plugging in the additional AR1031(s).
Otherwise, you’ll need to re-plug the additional AR1031(s).
Connect your PC to the rst AR1031’s Wi-Fi network (SSID),
and then type the last 8 digits of the AR1031 serial number
in the password eld.
Launch a web browser, and enter http://kaonmesh■■■■
(■■■■ is the last 4 digits of the rst AR1031’s serial
number) in the address bar, then press.
Enter the default
user name : admin and
password : password in the elds.
a.
b.
c.
Note You can view and change your Wi-Fi name (SSID) and
password, and see all your AR1031s congured as a
mesh network in your Wi-Fi.
➊AR1031
�
�
�
�
➋Ethernet cable ➌Power adapter