Kappa CMR-100 User manual

Operation Manual
Model: Universal dimmer switch
Item No.: CMR-100
OVERVIEW:
Featuring an unique universal plug and play adaptor that allows remote controlling existing house hold dimmable LED,
dimmable energy saving lamp, incandescent lamp, 230V~ halogen lamp and 12V halogen lamp with inductive transformer
or electronic transformer.
Hassle free wiring and easy built-in 8 steps rotary dialer setup for adjusting the lowest brightness level accordingly to
different brands of lamp(s) used.
Compatible to available differenttype lamps of:
Incandescent andhalogen lamps (230V~) 20W-200W
Electronic transformers (12V~) up to 20W-200W
Inductive transformers (12V~): 40W-200W Max.
Dimmable energy saving lamp: 3W-24W
Dimmable LEDs 3W-24W
！Not compatible tofluorescent lamp
Specification
Wiring
Before commencing work, ALWAYS isolate the mains power supply andswitch off thecircuit breaker.
If universal dimmer receiver is to be fitted into a wall box, dismantle screw tab holder.
Connect AC wire and load to receiver block terminal.
A) Live AC 230Vwire into terminal “L-in”
B) Neutral AC 230V wire into terminal “N-in”
C) LoadLive wire into terminal “ -out”
D) LoadNeutral wire into terminal “N-out”
E) Connect back mains power supply.
F) LEDindicator will light ON andreadyfor pairing.

Pairing
The universal dimmer receiver can pair with up to 6 different remote controls at any one time as it has a maximum of 6
memories.
This receiver is not to be controlled by “Code Switch System” remote transmitters.
Only compatible to “Self Learning System” remote transmitters.
Pairing using LEARNING MODE:
1. On the universal dimmer receiver press the ‘Learn’button once, red LED will flash.
The universal dimmer receiver is now in learning mode.
2. Using a remote control press the ‘ON’button intended to be paired; the load will flash
twice to confirm that the remote control is now paired.
NOTE: Learning mode lasts for 12 seconds; if no signal is received from a remote control during this time then the dimmer
receiver will automatically exit learning mode without pairing the device.
To exit leaning mode manually, simply press the ‘Learn’ button again.
！If, during learning mode the load does not flash to confirm, this means that the universal dimmer receiver memory is
FULL and no further remote control may be paired unless one of the existing remote control is first unpaired (see below).
Un-pairing
Removing single Device:
1. On the universal dimmer receiver press the ‘Learn’button once, red LED will flash. The universal dimmer receiver is
now in learning mode.
2. Using a remote control press the ‘OFF’button intended to be unpaired; the load will flash twice to confirm that the
remote control is now unpaired.
Clearing Memory (will remove all paired remote controls):
On the universal dimmer receiver press the ‘Learn’button for 6 seconds (LED on receiver will flash), release then press
once again. The load will flash twice to confirm that all remote control is now unpaired.
Lowest brightness setup
！Recommend using the same brand of load at the same time.
1. From factory pre-set the rotary dialer will be at 8 position.
2. Connect all lamps and with the paired remote control turn ON the universal dimmer, the lamp will rise to 100%
brightness then dim down to the relevant brightness. You can clearly see the full range of dimming effect each time you
alter the rotary dialer.
Fig.1 Adjust the rotary dialer anticlockwise from 8 to 7, the LED will rise to 100% brightness then dim down to the
relevant brightness.
Fig.2 If you think the dim level is still too bright then alter further from 7 to 6, again the LED will rise to 100%
brightness then dim down to the relevant brightness.
Fig.3 If during this step the LED flickers or turns OFF, the alter one step back from 6 to 7 for the most appropriate dim
level setting.

Operation
Soft start ON/OFF Function:
Press the ‘ON’button on remote control, the lights will gradually illuminate.
Press the ‘OFF’ button on remote control, thelight will gradually turn OFF.
Dimming Function:
1. Make sure the load (light) is switched ON.
2. On the remote control press the ON button again, the loads will start to dim.
3. To stop atthe desired brightness level, press the ON button again.
Dimming level dims in cycle, during the cycle if no signal is given『with4 cycles it will stop at 100% brightness』.
！After setting a dimlevel using the remote control the lightis then switched OFF, the next time that the light is switched
back on again the dim level will automaticallyreturn to the previously stipulated setting.
Note:
This product is capable and safe for dimmable energy saving lamp and dimmable LEDs to operate up to 50W Max., but in
order to fulfil the regulation the product specification rating must indicate 24WMax.
Caution:
Please leave minimum of 1.5 meters in-between 2 or more receivers.
Specification:
RF frequency: 433.92 MHz
Input rating: 220-240V~50Hz
Output rating:
Incandescent andhalogen lamps (230V~):20W-200W Max.
Electronic transformers (12V~): 20W-200W Max.
Inductive transformers (12V~): 40W-200W Max.
Dimmable energy saving lamp: 3W-24W Max.
Dimmable LEDs: 3W-24W Max.
Standby power consumption: Below 1W.