KARAG CONCORDIA K-1080 User manual

CONCORDIA K-1080
Usage & Installation Manual

2、Usage instruction:2、Usage instruction:
Please read the booklet carefully before using.
1、Safety notice item:1、Safety notice item:
Power plug must be assembled with creepage protector and connected with the
terra wire, and follows the rules to operate. Power socket must be install
out of reach of water.
The massage bathtub must be assembled by the careerman.
When switch on the shower and linn faucet, please adjust the suitable water
temperature firstly, to avoid scalding and destroy the products.
Level the ground and wall corner, connect cool & hot water hose
correctly , assemble power socke t and reference the size 's parameter
to prepare th e drain outlet .
3、Way of installation.3、Way of installation.
Switch on the linn faucet/shower switch valve, switch on the cool water adjusting valve
firstly, then switch on the hot water adjusting valve, adjust the suitable water temperature
and water massage bathtub(Forbid to water the temperature higher 80℃ hot water
directly, or it will destroy the product), await the water line reach 2CM above jets, then
press the air switch to switch on the water pump ( forbid to make the water pump running
for a long timewithout water, or the water pump will destroy because of too high
temperature), left-right surf adjuster can adjust the size of current; turn the jets to adjust
single jet's current size to get the best massage impact.
Cardiopathy, hypertension and person who is unwell or after drinking, please
no not use the massage bathtub to avoid risk happening.
Children should be accompanied by the adult while using the massage bathtub.
Finish using, eliminate the water in massage bathtub, then water
suitable clear water, switch on the water pump to clean the
massage bathtub pipeline.
If you will not use the massage bathtub for a long time, please
cut off the source and power of massage bathtub.
Place the mas sage bathtub in the conf irmed position, adjust all
the underpr op to mak e them meeting the groun d and levelling.
Immit a spot of w ater in m assage bathtub, turn ing the drainer
handle, awa it finishing draining, ther e is not any water in the
massage bat htub more, or should rep eat the s tep 2, until there is
no water in bat htub.

4、Ma in te na nc e an d ma in ta in4、Ma in te na nc e an d ma in ta in
5、Cu rr en tl y fa ul t an al yz e.5、Cu rr en tl y fa ul t an al yz e.
Fault phen o m e n a Fault anal y z i n g Fault obviating
1.the air hose which connected w i th the air pump
switch was loosened. Connect anew correctly.
change
Obviate the supply of power faul t .
Take down the water recycle net an d ` c lean
away the sundries.
Change a new water pump.
Change the sealed gasket insid e t he adjustor .
Dredge and connect anew corre c t ly.
Change
Belock anew.
Clean way the old latex and connect with new latex.
Adjusting all grounded part s a nd make them
grounded correctly.
ake dow n th e wa ter recycl e ne t an d cl ean
.
Obviating the circuitry faul t
Change the transformer( forb i d
minishing the rated power.)
Change the bathtub bottom ligh t
(forbid increasing power)
5. the water pump was broken.
4.the water pump's impeller was locked by some sundries.
3.power plug haven't been inserted correctly or power
fault.
2.air pump switch was broken.
2.The air hose of surfing adjustor loosen,leak air or jam.
1. sealed washer aging and broken.
2.locked nut loosened.
3.connecting parts' latex aging.
1.grounded parts of bathtub hang in the air.
2.water inlet jaming
1.bathtub bottom light short circuit
2. bathtub bottom light is broken
3.transformer is broken.
1.Surfing adjustor was broke n .
Water pump
can not be
start up
surfing can
not adjust
make water
Shake acutely
Water pump works
but the bottom
]light is not light
Connect th e cool & ho t water p ipe cor rectl y, inse rt the dr ainin g hose
into the dra iner, i nsert t he powe r socke t corre ctly.
Place the ma ssage b athtu b in the po sitio n appre ssed to t he wall .,
Seal the con necti ve part s by sili cone bu ildin g seala nt.
Adjust all t he func tion wi th wate r to chec k if all fu nctio n are Ok
Daily clea ning wi th gene ral liq uid sco ur, ple ase do no t clean t he
bathtub wi th doug hty aci d, doug hty alk ali, la tex , ace tone an d the
chemical w hich co ntain ing met hacry lic, fo rmald ehyde , or it wil l make
the bathtu b face pa led, or d estro y the bat htub.
Polish the f ace sca r with 10 00# lev igati on sand p aper fi rstly , then
polish wit h 1500# s and pap er, pol ishin g with so ft clot h and too thpas te
at last.
Clean away t he scal e on the ba thtub f ace wit h citri c acid or v inega r.
Scrape the s tubbo rn blot ch with s ort clo th and to othpa ste.
After usin g for a lon g time, you can r enew th e batht ub with l uster w ax,
it will make t he prod uct loo k likes a n ew one.
aw ay th e su nd ri es

Cool water inl
Preparative draining outlet
Power socket
L
N
O
(ye llow gr een lin e)
MML
TR
S
Grounded
Electric blueprint:
Water and electric installation illustration
Controlling valve connecting illustration
Plug
S -----air pump switch M-----water pump motor
TR-----transformer(20-60w 110V/12v) L-----bathtub botto m l i g h t ( 20w/12v)
Hot water inl
900
070
400
排水口
Hot water inlet cool water inlet
Cont roll ing va lve
Shower
linn faucet
400

Product parts
Re fe re nc e si ze
K1080 Massage bathtub
Pi l l ow
li n n f aucet
Co o l w ater swit c h
Ho t w a ter switc h
Di s j oining wa t e r adjust o r v alve
Shower
Ai r p u mp switch
surfing adjusting valve
Bathtub bottom light
Drain valve
Ma s s age jets
Fi l t rating ne t
1400
1400
1485
863
863
620
1980