KARAG LILIAN K-1077 User manual

1 2 3 45 6 7 8
9
1110
12
13
1
2
3
4
6
7
8
9
Cool water on-off
Cool water on-off
Faucet hower or s adjustment
linn faucet
Shower
5
Water on-off pump
Air pump on-off
Adjustment of Surfing
Suction meatus of water
11
10
13
Water overflow
Massage jets
12 Pillow
Air bubble jets
LILIAN K-1077
Usage Installation

2，Usage instruction:2，Usage instruction:
Please read the booklet carefully before using.Please read the booklet carefully before using.
1，Safety notice item:1，Safety notice item:
Power plug must be assembled with creepage protector and connected with the
terra wire, and follows the rules to operate. Power socket must be install
out of reach of water.
The massage bathtub must be assembled by the careerman.
When switch on the shower and linn faucet, please adjust the suitable water
temperature firstly, to avoid scalding and destroy the products.
Level the ground and wall corner, connect cool & hot water hose
correctly, assemble power socket and reference the size's parameter
to prepare the drain outlet .
3，Way of installation.3，Way of installation.
Switch on the linn faucet/shower switch valve, switch on the cool water adjusting valve
firstly, then switch on the hot water adjusting valve, adjust the suitable water temperature
and water massage bathtub(Forbid to water the temperature higher 80℃ hot water
directly, or it will destroy the product), press the air switch to make the air pump running,
but must await the water line reach 2CM above jets, then press the air switch to switch on
the water pump ( forbid to make the water pump running for a long timewithout water, or the
water pump will destroy because of too high temperature), left-right surf adjuster can adjust
the size of current; turn the jets to adjust single jet's current size to get the best massage impact.
Cardiopathy, hypertension and person who is unwell or after drinking, please
no not use the massage bathtub to avoid risk happening.
Children should be accompanied by the adult while using the massage bathtub.
Finish using, eliminate the water in massage bathtub, then water
suitable clear water.
If you will not use the massage bathtub for a long time, please
shut off the source and power of massage bathtub.
Place the massage bathtub in the confirmed position, adjust all
the underprop to make them meeting the ground and levelling.
Immit a spot of water in massage bathtub, turning the drainer
handle, await finishing draining, there is not any water in the
massage bathtub more, or should repeat the step 2, until there is
no water in bathtub.

4，Maint enanc e and mai ntain4，Maint enanc e and mai ntain
5,Cur rentl y fault a nalyz e5,Cur rentl y fault a nalyz e
Fa ul t phe no me na Fa ul t ana ly zi ng Faul t obviati ng
1.th e air hose wh ich con nected wi th the air pump
swit ch was loos ened. Conn ect anew co rrect ly.
chan ge
Obvi ate the sup ply of po wer fault .
Take d own the wat er recy cle net and ` clean
away t he sundri es.
Chan ge a new wate r pump.
Chan ge the seal ed gask et inside t he adjust or .
Dred ge and conn ect ane w correct ly.
Chan ge
Belo ck anew.
Clean way the old latex and connect with new latex.
Adju sting all groun ded p arts and m ake t hem
grounded correctly.
ake down the water recycle ne t and c lea n
.
Obvi ating the c ircui try fault
Chan ge the tran sform er( forbi d
mini shing the r ated po wer.)
Chan ge the bath tub bot tom light
(for bid incre asing p ower)
5. the water pump was broken.
4.the water pump's impeller was locked by some sundries.
3.power plug haven't been inserted correctly or power
fault.
2.air pump switch was broken.
2.The air hose of surfing adjustor loosen,leak air or jam.
1. sealed washer aging and broken.
2.locked nut loosened.
3.connecting parts' latex aging.
1.grounded parts of bathtub hang in the air.
2.water inlet jaming
1.bathtub bottom light short circuit
2. bathtub bottom light is broken
3.transformer is broken.
1.Su rfing adj ustor w as broken .
Water/air
pump can not
be start up
surf ing can
not ad just
make w ater
Shak e acutely
Water pump works
but the bottom
]light is not light
Connect the cool & hot water pipe co rre ctl y, in ser t the draining hose
into the drainer, insert the pow er so cke t cor rec tly.
Place the massage bathtub in the p osi tio n app res sed to the wall.
Seal the connective parts by sil ico ne bu ild ing s ealant.
Adjust all the function with wat er to c hec k if al l fun ction are Ok
Daily cleaning with general li qui d sco ur, p lea se do not clean the
bathtub with doughty acid, dou ght y alk ali , lat ex , acetone and the
chemical which containi ng me tha cry lic , for maldehyde, or it will make
the bathtub face paled, or destr oy th e bat htu b.
Polish the face scar with 1000# le vig ati on sa nd pa per firstly, then
polish with 1500# sand paper, po lis hin g wit h sof t cloth and toothpaste
at last.
Clean away the scale on the bathtu b fac e wit h cit ric a cid or vinegar.
Scrape the stubborn blotch wit h sor t clo th an d too thpaste.
After using for a long time,you ca n ren ew th e bat htu b with luster wax,
it will make the product look like s a new o ne.
away t he sundri es

Cool wat er inl
Preparative draining outlet
Power so cket
Electric blueprint:
Water and electric installation illustration
Controlling valve connecting illustration
L
N
O
(yellow green line)
MML
TR
S
Grou nded
Plug
S -----a ir switch M -- ---wate r/air pump m otor
TR---- -transf or mer(20- 60w 220/12v ) L-----bat htub bott om light(20 w/12v)
Hot wate r inl
700
500
400
400
Hot wate r inlet cool wat er inlet
Cont rollin g valve
Shower
linn fau cet
L
N
O
(ye l lo w g re e n li n e)
MM
S
Gr ou nded
Pl ug
400
15 05
Water power Air power
Notice:Must advertence the nameplate before connect the power