Karakoram Prime Connect Quick setup guide

8x M6 washer
2x Bindings (L and R)
M6x8mm Buttonhead Screw
10x
4x for Flip-Speed Riser
6x extra for Tour Mode with thin core boards
M6x10mm Buttonhead Screw
6x Tour Mode
2x Tour Modes
PAGE 1 OF 7
Prime Connect Instructions_A02
www.karakoram.com
Prime Connect
instagram.com/karakorambc
(Sold Separately in some countries)
Large:11.5-13
Patented US8469372B2, US8733783B2, US9138628B2, 9937407B2 and Patents Pending
www.karakoram.com
SPLIT KIT
Quiver-Connector Hardware
(Heel Lever Size Adjustment)
(Binding Hardware, Interfaces)
some countries
Women's: W6-W8
Quiver-Connector
Medium: 8.5-11
Assembly and Use Instructions
video instructions or visit
***Hardware shown to scale
-M3 Allen Wrench (Highback Fwd Lean, Heel Lever Size Adjustment)
-Cresent Wrench or 8 mm socket
SPLIT KIT Hardware:
Tools:
-M4 Allen Wrench
Size Chart:
Small: 6-8
Scan QR Code for
Sold separately in
facebook.com/karakorambc
8x M6 x 14mm Flathead Screw
2x Tour Mode
Adapters
2x Single Flip-Speed Riser
2x Quiver-Connector
1x Ride Mode 2.0 - Left and Right
8x
Ride Mode 2.0
M6x14mm Flathead Screw
4x M5 Nylock Nut
Tour Mode Adapter
Tour Mode Adapter
M5x 10 mm Buttonhead Screw
4x

W
PAGE 2 OF 7
Prime Connect Instructions_A02
3. Close Lock-block over Power-Link Lever
Lock-Block
Stance Width
or
Heel/Toe Position
Y
AA
Power-Link Lever
8x M6 x 14mm Flathead Screw
Quiver-Connector Installation
Quiver-Connector Use
Open Power-Link Lever to1.
install binding onto Quiver-
Connector
Close Power-Link Lever to2.
attach binding to Quiver-
Connector
Disk Micro-Adjustment
8x
M6 washer

Split Kit Installation
4x
AC
AJ
M5x 6mm Buttonhead Screw
1.
Cut Toe Ramp of with
Box Cutter along score line.
Remove Toe Ramp
and spacers
2x Tour Mode
Adapters
2.
PAGE 3 OF 7
Prime Connect Instructions_A02
M5 Nylock Nut
4x Tour Mode Adapter
M5x 10 mm Buttonhead Screw

M6x10mm Buttonhead Screw
Use M6x8mm Buttonhead
for thin core boards
PAGE 4 OF 7
Prime Connect Instructions_A02
Right
Angles in 3° increments
4x M6x8mm Buttonhead
Screw
Left
3.
4.
C. Reinstall Hardware
Angle Plate
A. Remove Hardware
B. Flip Angle Plates
6x
Set Toeside Stance Angles Preset Angles:
Front Foot: 30° max, -10° min
Back Foot: 10° max, -30° min
For greater than 10° on Back Foot
Production Splitboard Installation
M6x10mm Buttonhead Screw
Use M6x8mm Buttonhead
for thin core boards

5.
Loosely tighten screws on1.
toeside and heelside of Ride
Mode 2.0
Align heelside angle to2.
match toeside angle
Match alignment arrows and align3.
seam marks with seam of splitboard
Tighten screws4.
Test fit bindings5.
R
Seam Mark Alignment
Arrows
Alignment
Arrows
Seam Mark
Seam of Splitboard
Heelside Angle
PAGE 5 OF 7
Prime Connect Instructions_A02
8x M6x14mm Flathead Screw

PAGE 6 OF 7
Prime Connect Instructions_A02
0° 10°
AH AH
with M3 Allen
1/4 turn past hand
tight.
1. 4X Loosen Screws
3. Tighten Screws
2. Adjust position of
toestay
AG AG
6. Binding Size Adjustment
Size Setting:
S: 6-7
M:8.5-9.5
L: 11.5
WS: W6-W7
WM: W8.5-W9.5
Size Setting:
S: 7-8
M:9.5-11
L: 12-13
WS: W7-W8
WM: W10-W11
Forward Lean Adjustment:
Bindings come set
at 12° fwd lean
SMALL POSITION
LooserTighter
LARGE POSITION
7. Binding Fit
!Only adjust if
binding is loose
on ride mode
22°

Prime Splitboard System Use Instructions
Attach binding to Ride2.
Mode, aligning Toe Pins and
Ride Mode Toe Attachment
Close Heel Lever and Safety3.
Ride Mode:
Open Heelcup Lever1.
Toe Pins
V
PAGE 7 OF 7
Prime Connect Instructions_A02