Karisma FABLE Technical manual

INSTRUCTIONS FOR USE, INSTALLATION AND
ROUTINE MAINTENANCE
FABLE
SHAMPOO-BED

2
CONTENTS
Instructions for Installation, Use and Maintenance
INTRODUCTION................................................................................................................................................................3
PREREQUISITES..................................................................................................................................................................4
INTENDEDUSE..................................................................................................................................................................4
CONTRAINDICATIONS OF USE ....................................................................................................................................5
DEFINITION........................................................................................................................................................................5
SAFETY ...............................................................................................................................................................................5
LIFTING AND TRANSPORT ...........................................................................................................................................5
TECHNICAL SPECIFICATIONS .....................................................................................................................................6
TRANSPORT AND STORAGE ..................................................................................................................................... 6
DIMENSIONS AND INSTALLATION PLAN ............................................................................................................. 7
MIXER SPECIFICATIONS ........................................................................................................................................... 8
THERMOSTATIC MIXER SPECIFICATIONS ............................................................................................................ 8
INSTALLATION
PREPARATION ...............................................................................................................................................................9
WATER AND ELECTRICAL CONNECTION ............................................................................................................10
USE
SWITCHING ON THE SHAMPOO-BED ................................................................................................................11
COMFORT RELAX BACKREST CONTROLS .........................................................................................................11
AIR JET MASSAGE CONTROLS .................................................................................................................................12
THERMIC HEATED MATTRESS CONTROL ..........................................................................................................13
USING NECK RESTS WITH GEL BALLS .................................................................................................................14
DISASSEMBLING THE MIXER AND HAND SHOWER ...........................................................................................14
REMOVING THE GEL NECK REST ..............................................................................................................................15
USING THE REGULAR AND SMALL PALETTE TRAYS .........................................................................................15
USING THE HEADREST/FACE CUSHION ..............................................................................................................16
USINGTHE CUSHIONS (TRAPEZOIDAL, CYLINDRICAL AND SEMI-CYLINDRICAL) ...................................16
USING THE STEP .........................................................................................................................................................17
USING THE PAPER-ROLL HOLDER ..........................................................................................................................17
USING THE SERVICE TROLLEY ...................................................................................................................................18
MAINTENANCE
DISCONNECTION FOR MAINTENANCE ..................................................................................................................18
ROUTINE MAINTENANCE ..........................................................................................................................................18
IDENTIFICATION OF THE EQUIPMENT ................................................................................................................20
INSTRUCTIONS FOR DISPOSAL ........................................................................................................................21

3
Thank you for purchasing a Karisma product. we are certain you will be fully satised with your
choice.
Karisma products are manufactured according to strict quality standards using only the best
components.
The operation and safety of each Fable shampoo-bed were tested in painstaking detail before shipment.
Check that the shampoo-bed was not damaged during transport in a manner that could impair its opera-
tion and safety.
You are advised to follow the instructions contained in this manual carefully for the best reliability, long
life and top-notch performance of the shampoo-bed.
This manual is designed to allow you to use the Fable shampoo-bed in the best and safest manner. It is
therefore an integral part of the shampoo-bed. It must be kept carefully throughout the duration of the
shampoo-bed and accompany the shampoo-bed if it is transferred to a new user.
To avoid problems, read this manual carefully before carrying out any operation on the shampoo-bed
and follow the instructions scrupulously.
The manufacturer accepts no liability for damage caused by negligence and/or failure to observe the
instructions in this manual.
Without prejudice to the main technical and safety features, the manufacturer reserves the right to make
changes to the shampoo-bed for reasons of continual technical and technological evolution without
prior notice, without incurring any penalty.
The partial or total reproduction of this manual, including texts and illustrations, is prohibited by law.
The Court of Reggio Emilia (Italy) is competent in case of disputes.
INTRODUCTION
Instructions for Installation, Use and Maintenance

4
PREREQUISITES
Instructions for Installation, Use and Maintenance
The Fable shampoo-bed is the winning combination of functionality, attention to detail and exibility of
use in a product with a stylish design that revolutionises the concept of treatments, elevating it to the
nth power. In terms of looks, it is a bed with a wide array of external nishes, including luxurious quilted
padding. Side panels with LED-backlit methacrylate porthole can be chosen to make the equipment
even more striking. But it is in its potentials of use that Fable reaches new heights oering the ability to
span across an array of eco-natural healing, trendy, classic glamour and cross-contamination treatments,
for instance, facilitated by the use of a regular or large tray, complete with special bowls. The equipment
is designed to allow treatments from the above and from a privileged position. Extremely important is
the physical well-being that Fable oers, combining a relaxing air massage with the pleasant and gradual
comfort of the heated mattress, a classic horizontal position and an electrically adjustable backrest. The
use of a complete series of dedicated accessories, including specially shaped memory foam cushions
(trapezoidal for the feet, cylindrical and semi-cylindrical for the knees and legs), a headrest cushion with
an opening for the face and a service trolley.
INTENDED USE
The following requirements must be observed for a correct and safe installation of the equipment:
• The oor must comply with the laws and regulations in force in the place of use.
• The electrical system must comply with the laws and regulations in force in the place of use and be
equipped with a dierential switch to ensure the protection of persons against indirect electrical
contacts.
• Do not connect devices that are not specied as part of the system.
• The power supply must be sized for the following specications: 230-240 V, 50-60 Hz, 10A.
• In particular, earthing must be carried out following the laws and regulations in force in the place of
use.
• This equipment can only be used by the personnel who carry out the treatment (hairdresser,
hairstylist, hair therapist, beautician, masseur, etc.), hereinafter referred to as the operator.
Cleaning and maintenance must not be carried out by children without supervision.
• The treatment receivers can be adult persons as well as children from the age of 8 years
and people with reduced physical, sensory or mental capacities or lack of experience and
knowledge provided that they are supervised.
• Children must not be left unattended near the equipment.
• Cleaning and maintenance must only be carried out by persons qualied for this task.
• If the power cord is damaged, it must be replaced by the manufacturer, a technical assistance
technician or qualied personnel.
• Stop using the equipment immediately in the event of any water leakage.
• Cut o the equipment from the power and water supply (hot and cold) after use.
The manufacturer is not liable for the safety and reliability of the equipment if:
• installation and repairs are not carried out by authorised technicians
• the general and electrical installation of the room does not comply with the requirements of the
law
• the equipment was not installed following this manual
• the equipment is not used following this manual.

5
The wash unit chair is intended for professional use in hair treatment salons, particularly in the hair wash-
ing area. It cannot be used by more than one operator at the same time and can accommodate only one
customer at a time. The maximum load capacity is 120 kg. The installation is compliant if carried out ac-
cording to the specications indicated in the Installation, Use and Maintenance Manual. It is not allowed
to sit on the worktops. It is not permitted for more than one person to sit together.
Beware of scalding caused by hot water.
Beware of moving parts of the wash unit chair.
CONTRAINDICATIONS OF USE
Hairdresser, or operator, is the person who performs the treatment of the customer's hair and who man-
ages the operation of the wash unit chair. The workstation is situated at the back of the wash unit chair.
Customer is the person who is receiving the hair treatment. The front part of the wash unit chair is used
to seat the customer.
DEFINITIONS
The equipment complies with the essential European Union regulations on ergonomics
and safety. The manufacturer guarantees these qualities by axing the CE marking.
SAFETY
It is equipped with a special compartment for storage when not in use and the paper roll holder and de-
signed to pamper the customer during all treatments – beauty, massage and hair removal and the most
exclusive.
The Fable shampoo-bed is supplied on a pallet, to which it is xed through special holes on the base with
four screws and nut (on the underside of the pallet), and packed in a triple-wall corrugated cardboard
box. The pallet can be picked up in four ways by forklift. Information for the handling and the opening of
the package is shown on the package.
LIFTING AND TRANSPORT

6
Standard specications Unit of measure
mm
Value
790
The packages must be transported on closed vehicles. Do not drop or tilt packages during loading and
unloading. The products must be stored in a dry, indoor place, stacking up to three packages on top of
each other and without drastic temperature changes.
Environmental conditions for transport and storage
• Ambient temperature from -25°C to +50°C.
• Relative humidity max 75%.
Environmental conditions of use
• Ambient temperature from +10°C to +40°C.
• Relative humidity from 30% to 75%.
The shampoo-bed table must be used in a work environment with local lighting of 500 Lux or
greater.
The sound pressure level in the workplace is less than 70dB(A).
TRANSPORT AND STORAGE
TECHNICAL SPECIFICATIONS
Minimum seat height
mm 910
Maximum basin height
kg 120 (1 person)
Maximum ow rate
V ~ 230 - 240
Supply voltage
Hz 50 - 60
Frequency
W 650
Drawn power (max.)
min. 8
Operating mode (intermittent massage *)
min. 60 - 120
Operating mode (heated mattress **)
mm 2060
Footprint
Max. length
mm 655Max. depth
mm 790 - 980Max. height
kg 120Weight
* Referred to model with jet massage function.
** Referred to Thermic model.

7
DIMENSIONS
DIMENSIONS EXPRESSED IN MM
2060
900
990
120
180
17°
480
860 270
990
790
566
655
411
ELECTRIC CORD 3X1.5 (1000MM)
220/240 V- 50-60 Hz
400
655
RECOMMENDED
LOCATION 960
2200
650
1100
50
500
50
600
1310
340
200
120
1
2
3
4
1000
DETAIL A
1
2
3
4
100
100
12
3
80
80
1215
120
17°
860411 270
1215
600
A
3300
150MIN.
310MAX.
175
HOLE ø 80 mm
DONE ONLY
ON REQUEST FOR
WATER SYSTEMS
FROM THE WALL
DIMENSIONS
EXPRESSED
IN MM
ATTENTION ! ONLY ON REQUEST
WATER SYSTEM INSTALLATION POSITION FOR WALL-MOUNTED VERSION
RECOMMENDED HALF (MAX AREA OF USE MM 85 X 250 H)
MINIMUM
RECOMMENDED
ENTIRE AREA AVAILABLE
FOR POWER OUTPUT
MM 1100X 500 APPROX
(RECOMMENDED POSITION TO MAINTAIN
AN EMPTY SPACE UNDER THE BED)
DOUBLE AREA MM 120 X 400 + 175 X 400 TO BE USED FOR WATER
CONNECTION ON THE LEFT AND RIGHT SIDE OF THE BED CROSSBAR
ATTENTION :
TO USE THE TRAY-LARGE COD. 156
IT IS NECESSARY TO INCREASE THIS
SIZE OF
+ 120 MM , AND THAT ALSO
FROM THE SIDE WALL OF +
150 MM
FIXED FLANGE
ON SIDE WITH
SPECIAL SCREWS
INSTALLATION SURFACE STANDARD
WALL INSTALLATION PLAN - ON REQUEST ONLY

8Instructions for Installation, Use and Maintenance
A hot and cold water tap must be provided upstream of each piece of equipment for the plumbing sys-
tem.
Connections to the sewage drain system are established using a ø 40 mm drain pipe.
WARNING:
The equipment does not have a siphon so one must be provided in the plumbing system.
Connection to the mains power supply is 230 V ~ 50 Hz F+N+T. The maximum power consumption of the
shampoo-bed is about 650 W.
It is necessary to provide easy access to the water and electricity supply of the wash unit to allow discon-
nection in case of need.
MIXER SPECIFICATIONS
Technical specications
Test pressure 15 bar
Cold water supply blue indicator pointing rightwards. Pipe connection 3/8″
Hot water supply red indicator pointing leftwards. Pipe connection 3/8″
Limits of use according to UNI 10234 EN (817):
MIN. pressure 0.5 bar MAX. 10 bar (100000000 pascals)
MAX. temperature 90°
Limits of use recommended by UNI 10234 (EN 817) for a good tap operation
Pressure: MIN. 0.5 bar MAX. 5 bar (50000000 pascals)
Temperature: MAX. 65°C
Warnings:
- The system pipes must be carefully rinsed to avoid damage to the taps caused by any residues in the
pipes.
- It is recommended to install a pressure reducer in case of operating pressures above 5 bar.
- It is also recommended to install a central lter for water with a high impurity content.
Technical specications
Test pressure 15 bar
Cold water supply blue indicator pointing rightwards. 1/2" pipe connection
Hot water supply red indicator pointing leftwards. 1/2" pipe connection
Limits of use according to UNI 10234 EN (817):
MIN. pressure 1 bar MAX. 10 bar (100000000 pascals)
MAX. temperature 90°
Limits of use recommended by UNI 10234 (EN 817) for a good tap operation
Pressure: MIN. 1 bar MAX. 5 bar (50000000 pascals)
Temperature: MAX. 65°C
Warnings:
- The system pipes must be carefully rinsed to avoid damage to the taps caused by any residues in the
pipes.
- It is recommended to install a pressure reducer in case of operating pressures above 5 bar.
- It is also recommended to install a central lter for water with a high impurity content.
THERMOSTATIC MIXER SPECIFICATIONS

9
Preparation
1) Remove upper and side parts of the packaging leaving the shampoo-bed mounted on the pallet so
that it is easier to transport. Remove the shampoo-bed protections and any accessories contained in the
packaging itself.
Fixing the shampoo-bed
INSTALLATION
Instructions for Installation, Use and Maintenance
1) Warning: DO NOT LIFT IN THE POINTS Lift the shampoo-bed in the indicated points to bring it
closer to the pre-set point of use. There are three lifting points. It is advisable to employ three people and
never fewer than two to handle the shampoo-bed.
2) Before installing the water and electric unit and removing the pallet, undo the three screws that x
the bed to the bed (1), unhook the mattress by pulling it back, turn it longitudinally on one side (2) to dis-
connect the connection pins of the air massage or the heater, according to the version (3), to access the
inside of the bed from the upper part. Now remove the four screws securing the bed to the pallet (two
front and two rear screws) to position the bed at the predetermined point of use.
WARNING: Handle as indicated in Point 1.

10
4) Make the water connection at the rear as indicated in the technical data sheet (1), providing a tap for
hot and cold water upstream of each piece of equipment. Connections to the sewage system are estab-
lished using a ø 40 drain pipe.
3) Establish the electrical connection (4) of the shampoo-bed to the mains conductor of a sectional
switch located near the equipment. The equipment is supplied with a 1.5 m long cord and Schuko plug
because it is not possible to determine the length of the power supply cable according to the require-
ments of each customer. The installer will be responsible for tting an easily accessible disconnecting
device (In=10 A Idn = 30 m A) on the electrical connection, in compliance with the laws in force in the
country of use and with the instructions contained in the Installation, Use and Maintenance Manual, and
carrying out a complete test of the equipment. Check the presence and operation of the dierential pro-
tection against indirect contacts.
10
10
10
10
1 2
3
4
Plant layout
1 = Hot 3/8" (1/2" thermostatic mixer)
2 = Cold 3/8" (1/2" thermostatic mixer)
3 = ø 40 mm drain
4 = Electrical cable outlet (where required)
Cord 3X1 (1500 mm) - 220/240 V - 50 Hz/60 Hz