Karla Dubois GATSBY User manual

B O X C O N T E N T S
A.0H E A D BORDx 1
B.0F OOTBOARDx 1
C.0S I DE PANEL x 2
LEG S x 4D.0
E.0BOTTOM PANEL x2
F.0S I DE BRACKET x 4
G.0SUPPORT BRACKET x4
W O O D E N S T ABI L I Z E R x 2
H .
J. 0SCREW x4
I. 0A LLEN BOLT 1” x16
K.0WASHER x4
L.0ALLEN WRENCH x1
H O M E
B. QTY1
E. QTY4
F. QTY4
D. QTY4
C. QTY2
A. QTY1
G. QTY4
K. QTY8
J. QTY8
I. QTY16
L. QTY1
H. QTY2

WHAT YOU WILL NEED
C.0SIDE PANEL x2
F.0SIDE BRACKET x4
I. 0ALLEN BOLTS 1” x16
G.0SUPPORT BRACKET
SCREWS x8
WASHER x8
ALLEN WRENCH x1
J. 0
FIGURE 1
02
K.0
L.0
STEP: 01
STEP: 02
Set Side Bracket ( F ) on the Side Panel ( C ) as shown below in Example 1.
Place bracket so the two holes are against the Fabric. Next, place the 1”

shown in Example 2. DO NOT OVERTIGHTEN.

SEE FIGURE 1
SEE FIGURE 2


DO
NOT OVERTIGHTEN.
FIGURE 2

wHAT YOU WILL NEED
03
A.0HEADBOARD
B.0FOOTBOARD
C.0ALLEN BOLT 1”
0
E.0ALLEN WRENCH
I. WOODEN STABILIZER
SIDE PANEL W/ BRACKETS INSTALLED
STEP04
STEP 05
STEP 03
WITH BOTH THE HEADBOARD (A) AND FOOTBOARD ( B ), USE THE REMAIN-
ING 8 ALLEN HEAD BOLTS (I) TO SCREW INTO FOUR BOTTOM HOLES ON
EACH OF THE PIECES. LEAVE THESE BOLTS LOOSE.
STEP 05
STEP 04
STEP 05
TAKE THE HEADBOARD (A) AND ALIGN THE BOLTS
TO THE SIDE BRACKET (E) THAT IS ALREADY
ATTACHED TO ONE OF THE SIDE PANELS. ONCE
PLACED INSIDE THE HOLE, PRESS DOWN TO LOCK
THE BOLT IN PLACE. DO SO UNTIL BOTH THE HEAD-
BOARD (A) AND FOOTBOARD (B) ARE ATTACHED
TO THE SIDE PANELS (C). ONCE ALL PIECES ARE
ATTACHED, BEGIN TO TIGHTEN EACH OF THE
BOLTS USING THE ALLEN WRENCH (L).
FLIP OVER THE TODDLER BED WHEN YOU’VE FINISHED
ASSEMBLING THE FOUR PIECES OF THE BED TOGETHER.
ONCE IT IS FLIPPED ON IT’S SIDE, BEGIN TWISTING THE
LEGS INTO THE SIDE BRACKETS.
WHEN FINISHED WITH ALL FOUR LEGS, FLIP OVER SO THAT
THE BED IS NOW STANDING ON IT’S LEGS. PLACE BOTH
WOODEN STABILIZER (I) INSIDE THE STABILIZER BRACKET TO
SECURE THEM IN PLACE.
STEP 06

wHAT YOU WILL NEED
04
H O M E
I. 0BOTTO M P
BOTTOM PANELS
A N E L x 2
STEP 07
THE LAST STEP TO BUILDING THE GATSBY TWIN BED IS TO LAY THE
BOTTOM PANELS DOWN, SIDE BY SIDE, ONTO THE WOODEN SUPPORTS.
CHECK ALL BOLTS TO BE SURE THAT THEY ARE SECURED BEFORE
PLACING MATTRESS DOWN.
CARE AND MAINTENANCE
PERIODICALLY CHECK YOUR BED FOR ANY LOOSE BOLTS AND SCREWS AND TIGHTEN WHERE NEEDED. IF BED IS DAMAGED, DO NOT
USE. CONTACT US FOR REPLACEMENT PARTS. SPOT CLEAN ONLY. AVOID EXCESS MOISTURE.
PLEASE VISIT OUR WEBSITE AT WWW.KARLADUBOIS.COM THERE, YOU CAN FIND MORE PRODUCT INFORMATION,
REGISTER YOUR PRODUCT, CONTACT US OR REQUEST REPLACEMENT PARTS.
YOU CAN EMAIL OR WRITE
[email protected]
KARLA DUBOIS
14001 ROSECRANS AVE
LA MIRADA, CA 90638
ONE YEAR LIMITED WARRANTY
CONTACT US
DEFECTIVE PARTS WILL BE REPLACED WITH A ONE YEAR PERIOD FROM DATE OF ORIGINAL PURCHASE. MISSING PARTS WILL BE
REPLACED WITHON 30 DAYS FROM THE DAY OF ORIGINAL PURCHASE. KARLA DUBOIS WARRANTS ONLY NEW UNITS PUCHASED IN
IT’S ORIGINAL PACKAGING. THE WARRANTY DOES NOT COVER USED, SECOND HAND OR DEMOS AND IS NON-TRANSFERABLE.
ANY DAMAGED OR DEFECTIVE PART THAT RESULTS FROM NORMAL WEAR AND TEAR, ABUSE, NEGLIGENCE, IMPROPOSER USE OR
ALTERNATION TO THE FINISH, DESIGN AND HARDWARE OF THE BED, OR THE ASSEMBLY OF THIS PRODUCT ARE NOT COVERED. THE
SPECIFIC LEGAL RIGHTS OF THIS WARRANTY MAY VARY FROM STATE TO STATE. SOME STATES DO NOT ALLOW ANY EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIL DAMAGES. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN
IMPLIED WARRANTY LASTS.