Kasda KA300 User manual

KA300 Wireless Router
User Manual
www.kasda.cc Kasda Digital Technology Co.,Ltd

KA300 Wireless Router User Manual
NOTICE
This document contains proprietary information protected by copyright, and this
Manual and all the accompanying hardware, software, and documentation are
copyrighted. All rights are reserved. No part of this document may be photocopied or
reproduced by mechanical, electronic, or other means in any form.
The manufacturer does not warrant that the hardware will work properly in all
environments and applications, and makes no warranty or representation, either
expressed or implied, with respect to the quality, performance, merchantability, or
fitness for a particular purpose of the software or documentation. The manufacturer
reserves the right to make changes to the hardware, software, and documentation
without obligation to notify any person or organization of the revision or change.
All brand and product names are the trademarks of their respective owners.
© Copyright 2014
All rights reserved.

KA300 Wireless Router User Manual
1
Content
1 INTRODUCTION ...................................................................................................................... 3
1.1 MAIN FEATURES .............................................................................................................. 3
1.1.1 Wireless ............................................................................................................................... 3
1.1.2 Network Protocol and Features............................................................................................ 3
1.1.3 Firewall................................................................................................................................ 3
1.1.4 Management Support........................................................................................................... 4
1.1.5 Operating System Support................................................................................................... 4
1.1.6 Environmental...................................................................................................................... 4
1.2 PACKET CONTENTS ....................................................................................................... 4
1.3 SYSTEM REQUIREMENTS ............................................................................................... 4
1.4 FACTORY DEFAULTS...................................................................................................... 5
1.5 WARNINGS AND CAUTIONS............................................................................................. 5
2 HARDWARE DESCRIPTION................................................................................................... 6
3HARDWARE INSTALLATION............................................................................................... 8
4 PC CONFIGURATION GUIDE .............................................................................................. 9
4.1 LOCAL PC CONFIGURATION IN WINDOWS 95,98,ME, XP,7.............................................. 9
4.2 LOCAL PC CONFIGURATION IN WINDOWS 2000 ................................................................ 9
5 QUICK SETUP OF THE ROUTER ........................................................................................ 10
6 WEB-BASED BASIC MANAGEMENT GUIDE..................................................................... 13
6.1 HOME PAGE BASIC SETTING ............................................................................................ 13
6.1.1 Network (WANSettings) ...................................................................................................13
6.1.2 LAN Settings ..................................................................................................................... 15
6.1.3 Wireless Settings ............................................................................................................... 17
6.2 PARENTAL CONTROL .................................................................................................... 17
6.3 ADMINISTRATION.......................................................................................................... 18
6.3.1 Time setting ....................................................................................................................... 18
6.3.2 Password:...........................................................................................................................19
6.3.3 Backup/restore/reset........................................................................................................... 19
6.3.4 Firmware update................................................................................................................ 20
7WEB-BASED ADVANCE MANAGEMENT GUIDE ............................................................. 21
7.1 SETUP............................................................................................................................ 21
7.1.1 WAN setup ........................................................................................................................ 21
7.1.2 LAN setup.......................................................................................................................24
7.1.3 IPV6................................................................................................................................... 25
7.1.4 Advanced Routing Setup ................................................................................................ 26
7.2 WIRELESS SETUP ........................................................................................................... 27
7.2.1 Wireless Basic Settings...................................................................................................... 27
7.2.2 Guest Access......................................................................................................................28
7.2.3 Security.............................................................................................................................. 29
7.2.4 WPS Setup......................................................................................................................... 30
7.2.5 Wireless Access Setup....................................................................................................... 31

KA300 Wireless Router User Manual
2
7.2.6 WDS Setup ........................................................................................................................ 32
7.3 SERVICE –QOSSETUP ................................................................................................. 35
7.4 SECURITY SETUP ......................................................................................................... 36
7.4.1 Firewall setup..................................................................................................................... 36
7.4.2 URL Setup .........................................................................................................................37
7.4.3 Remote Access Setup......................................................................................................... 37
7.4.4 DoS.................................................................................................................................... 38
APPENDIX: FREQUENT ASKED QUESTIONS...................................................................... 39

KA300 Wireless Router User Manual
3
1 Introduction
Thank you for choosing our product. The KA300 Wireless Router uses Broadcom’s
CPE solution that fully complies with IEEE802.11b/g/n standards. It will provide
your SOHO with convenient Internet.
1.1 Main Features
1.1.1 Wireless
Fully IEEE 802.11b /g /n compatible.
Wireless data rate up to 300 Mbps
Operating in the unlicensed 2.4 GHz ISM band
Supports 64/128 bits WEP, WPA, WPA2, WPA/WPA2-PSK,
802.1x
1.1.2 Network Protocol and Features
Ethernet to ADSL Self-Learning Transparent Bridging
Internet Control Message Protocol (ICMP)
IP Static Routing
Routing Information Protocol (RIP, RIPv2)
Network Address Translation (NAT)
Virtual Server, Port Forwarding
Dynamic Host Configuration Protocol (DHCP)
DDNS
Simple Network Time Protocol (SNTP)
VPN pass-through (IPSec/PPTP/L2TP)
Parent control
1.1.3 Firewall
Built-in NAT
MAC Filtering
Packet Filtering

KA300 Wireless Router User Manual
4
Stateful Packet Inspection (SPI)
Denial of Service Prevention (DoS)
DMZ
1.1.4 Management Support
Web Based GUI
Upgrade or update via FTP/HTTP
Command Line Interface via Telnet
Diagnostic Test
Firmware upgrade-able for future feature enhancement
1.1.5 Operating System Support
WINDOWS 98/SE/ME/2000/XP/VISTA/7
Macintosh
LINUX
1.1.6 Environmental
Operating humidity: 10%-90% non-condensing
Non-operating storage humidity: 5%-95% non-condensing
1.2 Packet Contents
The packet contents are as the following:
ROUTER x 1
Power Adapter x 1
Ethernet Cable x 1
CD x 1
1.3 System Requirements
Broadband Internet Access Service (DSL/Cable/Ethernet)
One DSL/Cable Modem that has an RJ45 connector (which is not
necessary if the Router is connected directly to the Ethernet)

KA300 Wireless Router User Manual
5
PCs with a working Ethernet Adapter and an Ethernet cable with RJ45
TCP/IP protocol on each PC
Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or
Apple Safari
1.4 Factory Defaults
The device is configured with the following factory defaults:
IP Address: 192.168.1.1
Subnet Mask: 255.255.255.0
1.5 Warnings and Cautions
never use the product near water.
To prevent dangerous overloading of the power circuit, be careful about
the designed maximum power load ratings. Not to follow the rating
guideline could result in a dangerous situation.
Please note that telephone line on modem must adopt the primary line
that directly outputs from junction box. Do not connect Router to
extension phone. In addition, if your house developer divides a telephone
line to multi sockets inside the wall of house, please only use the
telephone that has connected with the splitter of ADSL Router when you
access the Internet. Under the above condition, if you also install
telephone with anti-cheat-dial device, please pull out this kind of
telephone, otherwise ADSL Router may occur frequently off-line.

KA300 Wireless Router User Manual
6
2 Hardware Description
Front Panel
LED
Color
Function
Blue
Off: Power Not Supplied
On: Power Supplied
Blue
On: The WAN port has detected a link with an attached device
Blinking: Data is being transmitted or received bythe WAN port
Off: No WAN link via the WAN port
Blue
On: LAN link established and active via LAN port
Blinking: ADSL data activity occurs
Off: No LAN link via LAN port
Blue
On: The wireless module is ready and idle
Blinking: Data transmitting or receiving over WLAN
Off: The wireless function is off
Blue
On: WPS connection is established
Blinking: Trying to establish a WPS connection
Off: WPS function is off or no WPS connection

KA300 Wireless Router User Manual
7
Rear panel
Port
Function
WAN
Connect the device to a cable or DSL modem
ETH1,2,3,4
Connect the device to your PC's Ethernet port, or to
the uplink port on your hub/switch, using a RJ-45
cable
RESET
System reset or reset to factory defaults
WPS
On: WPS connection is established
Blinking: Trying to establish a WPS connection
Off: WPS function is off or no WPS connection
ON/OFF
Switch it on or off
POWER
Connect to the supplied power adapter

KA300 Wireless Router User Manual
8
3 Hardware Installation
This chapter shows you how to connect Router. Meanwhile, it introduces the
appropriate environment for the Router and installation instructions.
1. Using an Ethernet Cable to connect the WAN port of the ROUTER to a
cable or DSL modem.
2. Using an Ethernet Cable to connect the LAN port of the ROUTER to your
LAN or a PC with network card installed.
3. Connect the power cable to the PWR connector on ROUTER, then plug in
the power adapter to the AC power outlet, and then press the on-off button.

KA300 Wireless Router User Manual
9
4 PC Configuration Guide
4.1 Local PC Configuration in Windows 95, 98, ME, XP,7
1. In the Windows task bar, click the “Start” button, point to “Settings”, and then
click “Control Panel”.
2. Double-click the “Network” icon.
3. On the “Configuration” tab, select the TCP/IP network associated with your
network card and then click “Properties”.
4. In the “TCP/IP Properties” dialog box, click the “IP Address” tab. Set the IP
address as 192.168.1.x (x can be a decimal number from 2 to 254.) like
192.168.1.2, and the subnet mask as 255.255.255.0.
5. On the “Gateway” tab, set a new gateway as 192.168.1.1, and then click “Add”.
6. Configure the “DNS” tab if necessary. For information on the IP address of the
DNS server, please consult with your ISP.
7. Click “OK” twice to confirm and save your changes.
8. You will be prompted to restart Windows. Click “Yes”.
4.2 Local PC Configuration in Windows 2000
1. In the Windows task bar, click the “Start” button, point to “Settings”, and then
click “Control Panel”.
2. Double-click the “Network and Dial-up Connections” icon.
3. In the “Network and Dial-up Connections” window, right-click the “Local Area
Connection” icon, and then select “Properties”.
4. Highlight “Internet Protocol (TCP/IP)”, and then click “Properties”.
5. In the “Internet Protocol (TCP/IP) Properties” dialog box, set the IP address as
192.168.1.x (x can be a decimal number from 2 to 254.), and the subnet mask as
255.255.255.0 and the default gateway as 192.168.1.1. Then click “OK”.
6. Configure the “DNS” tab if necessary. For information on the IP address of the
DNS server, please consult with user’s ISP.
7. Click “OK” twice to confirm and save user’s changes.

KA300 Wireless Router User Manual
10
5 Quick Setup of the Router
In order to use the web-based management software, it will be necessary to use a
computer that occupies the same subnet as the Router. The simplest way to do this for
many users will be to use DHCP server that is enabled by default on the Router.please
make sure the wan connection is ok.
Internet Connection Setup Wizard will guide you through a step-by-step process to
configure your router and connect to the Internet.ill guide you through a step-by-step
process to configure your router and connect to the Internet.
(1) Launch a web browser, such as Internet Explorer, and then use http://192.168.1.1
to log on to the setting pages. Enter username “admin”and password “admin”,then
click “OK”.
(2) After log on ,you will see the following page. When WAN connection is ok，
please press next. When the wan connection is bad, please check your cable.
Click OK
Enter username ‘admin’
and password ‘admin’

KA300 Wireless Router User Manual
11
(3) The WAN connection type will appear, the quick setup supports two popular mode
PPPoE, DHCP(Dynamic IP) to connect to the internet,If the connection type is
PPPoE , enter the username and password provided by your ISP. If the connection
type is dynamic IP, the router will obtain an IP automatically from you ISP. Wireless
is enabled by default. please enter SSID and Password for wireless network Then
click “next”.

KA300 Wireless Router User Manual
12
(4)The Internet Connection Setup Wizard is complete. Click the Apply button to save
and apply your settings.
After the configuration above，Now you can surf the Internet.

KA300 Wireless Router User Manual
13
6 Web-based basic Management Guide
This chapter will introduce how to configure your router in detail，the home page is
as shown. From home page, you can find basic & Advanced Setup option on the top
router home configuration page. Basic menu has two options ,one is home and the
other is administration .Below the home menu，there are two options: home &
parent control.
6.1 home page basic setting
6.1.1 Network (WANSettings)
KA300 supports three types WAN connection.they are DHCP,Static IP,PPPOE, Select any of
them you will be able to configure the corresponding connection of WAN. Click the
icon ，the wan setup page will appear，as shown，you can configure the IP WAN
parameters

KA300 Wireless Router User Manual
14
DHCP connection type
If your ISP provides the DHCP service, please choose Dynamic IP type, and the Router
will automatically get IP parameters including IP address, Subnet Mask, Default
Gateway, from your ISP. You can see the page as follows .,
Click the Save Settings button to save your settings.
Static IP
If your ISP provides a static or fixed IP Address, Subnet Mask, Gateway and DNS
setting, select Static IP. The Static IP settings page will appear.

KA300 Wireless Router User Manual
15
IP Address: Enter the IP address in dotted-decimal notation provided by your ISP.
Subnet Mask: Enter the subnet Mask in dotted-decimal notation provided by your
ISP, usually is 255.255.255.0.
Default Gateway:(Optional) Enter the gateway IP ddress in
dotted-decimal notation provided by your ISP.
DNS1/DNS2(Optional) /DNS3(Optional) : Enter one or two DNS addresses in
dotted-decimal notation provided by your ISP.
Click the Save button to save your settings.
PPPOE
If your ISP provides a PPPoE connection, select PPPoE option. And you should enter the
following parameters.
User Name/Password - Enter the User Name and Password provided by your ISP. These
fields are case-sensitive.
Click the Save button to save your settings.
6.1.2 LAN Settings
Click (any lan port is OK) icon,you can configure the IP parameters of the LAN
on the screen as below.

KA300 Wireless Router User Manual
16
Local IP Address:Enter the IP address of your Router or reset it in dotted-decimal notation
(factory default: 192.168.1.1).
DHCP Server:Enable or Disable the DHCP server. If you disable the Server, you must have
another DHCP server within your network or else you must configure the computer manually.
Start IP Address:Specify an IP address for the DHCP Server to start with when assigning IP
addresses. 192.168.1.100 is the default start address.
End IP Address:Specify an IP address for the DHCP Server to end with when assigning IP
addresses. 192.168.1.150 is the default end address.
Click the Save button to save your settings.
Note:
1) If you change the IP Address of LAN, you must use the new IP Address to log in the
Router.
2) If the new LAN IP Address you set is not in the same subnet, the IP Address pool of the
DHCP server will change accordingly at the same time，while the Virtual Server and
DMZ Host will not take effect until they are re-configured.

KA300 Wireless Router User Manual
17
6.1.3 Wireless Settings
Cliick icon,you can configure the basic settings for the wireless network of
2.4GHz on this page.
Wireless enable :Enable or disable the Wirless function here.
Network Name（SSID）: Also called the SSID. Enter a value of up to 32 characters. The
same name must be assigned to all wireless devices in your network .
Wireless password : nothing or enter 8~64 characters for the wifi password.
Click the Save button to save your settings.
6.2 Parental Control
Parental control allows you to set the time limit for a client's network usage.
1. In the [Service Name] column, select the client whose network usage you want to
control. You may also key in the clients MAC address in the [Local MAC] column.
2. In the [Add / Delete] column, click the Edit icon.

KA300 Wireless Router User Manual
18
3. Set up allowed time limits in the [Time Settings] map. Drag and drop to desired
day/time.
6.3 Administration
6.3.1 Time setting
This page allows you to set the time manually or to configure automatic time synchronization.
The Router can automatically update the time from an NTP server via the
Internet.
Time Zone - Select your local time zone from this pull-down list.
Time Servers - Select the time servers.You can choose the place where you are.Or
select Custom to configure the servers by yourself.
Time will show up on the page(Advanced--Status--Status,Current Time).
Note: After you have made your changes, Click Save to apply the changes.