Kasda KF162 User manual

KF162 Wireless Router
User Manual

Wireless Router User Manual
NOTICE
This document contains proprietary information protected by copyright, and this Manual
and all the accompanying hardware, software, and documentation are copyrighted. All
rights are reserved. No part of this document may be photocopied or reproduced by
mechanical, electronic, or other means in any form.
The manufacturer does not warrant that the hardware will work properly in all
environments and applications, and makes no warranty or representation, either
expressed or implied, with respect to the quality, performance, merchantability, or
fitness for a particular purpose of the software or documentation. The manufacturer
reserves the right to make changes to the hardware, software, and documentation
without obligation to notify any person or organization of the revision or change.
All brand and product names are the trademarks of their respective owners.
© Copyright 2014
All rights reserved.

Wireless Router User Manual
Content
1 OVERVIEW..............................................................................................................................1
1.1 FEATURES...........................................................................................................................1
1.1.1 Wireless.......................................................................................................................1
1.1.2 Network Protocol & Features.....................................................................................1
1.1.3 VoIP..............................................................................................................................1
1.1.4 FIREWALL...................................................................................................................2
1.1.5 Management Support.................................................................................................2
1.1.6 Operating System Support.........................................................................................2
1.1.7 Environmental .............................................................................................................3
1.2 PACKET CONTENTS ...........................................................................................................3
1.3 SYSTEM REQUIREMENTS ...................................................................................................3
2 HARDWARE DESCRIPTION...................................................................................................4
3HARDWARE INSTALLATION...............................................................................................6
4PC CONFIGURATION GUIDE.............................................................................................7
4.1 LOCAL PC CONFIGURATION IN WINDOWS 95, 98, ME, XP,7................................................7
4.2 LOCAL PC CONFIGURATION IN WINDOWS 2000...................................................................7
5 WEB-BASED MANAGEMENT GUIDE....................................................................................8
5.1 LANSETTING PAGE.............................................................................................................8
5.2 INTERNET ACCESS CONFIGURATION....................................................................................8
5.2.1 Wide Area Network (WAN) Settings..........................................................................8
5.2.2 LAN Settings.............................................................................................................. 11
5.3 WIRELESS SETTING ........................................................................................................... 12
5.3.1 Basic...........................................................................................................................12
5.3.2 Advanced...................................................................................................................14
5.3.3 Security...................................................................................................................... 17
5.4VOICE CONFIGURATION.....................................................................................................21
5.4.1 SIP Basic Setting.......................................................................................................21
5.4.2 SIP Advanced Setting...............................................................................................22
5.5TR-069 CLIENT.................................................................................................................24
5.6PRINTER SERVER INSTALLATIONS..................................................................................... 25
TROUBLESHOOTING.................................................................................................................. 28

Wireless Router User Manual
1
1 Overview
Thank you for choosing our product. The KW5562 is a Wireless router, an 802.11n
wireless router, a 4-port switch, two FXS ports and a USB port in one unit, bringing
high-speed wireless Internet connection to a home or office.
1.1 Features
1.1.1 Wireless
Fully IEEE 802.11b & IEEE 802.11g & IEEE 802.11n
compatible.
Wireless data rate up to 300Mbps
Operating in the unlicensed 2.4 GHz ISM band
Multi-SSID
Supports 64/128 bit WEP security and user authentication
1.1.2 Network Protocol & Features
Transparent Bridging
Internet Control Message Protocol (ICMP)
IP Static Routing
Routing Information Protocol (RIP, RIPv2)
Network Address Translation (NAT)
Virtual Server, Port Forwarding
Dynamic Host Configuration Protocol (DHCP)
DNS Relay, DDNS
IGMP Proxy
Simple Network Time Protocol (SNTP)
VPN pass-through (IPSec/PPTP/L2TP)
Parent control
1.1.3 VoIP
SIP

Wireless Router User Manual
2
Voice codecs: G.711A/µ, G.723, G.726, G.729
Call waiting
Call forwarding
1.1.4 FIREWALL
Built-in NAT
MAC Filtering
Packet Filtering
Stateful Packet Inspection (SPI)
Denial of Service Prevention (DoS)
DMZ
1.1.5 Management Support
Web Based GUI
Upgrade or update via FTP/HTTP
Command Line Interface via Telnet
Diagnostic Test
Firmware upgradeable for future feature enhancement
1.1.6 Operating System Support
WINDOWS 98
WINDOWS 98 SE
WINDOWS ME
WINDOWS 2000
WINDOWS XP
WINDOWS VISTA
WINDOWS 7
Macintosh
LINUX

Wireless Router User Manual
3
1.1.7 Environmental
Operating humidity: 10%-90% non-condensing
Non-operating storage humidity: 5%-95% non-condensing
1.2 Packet Contents
The packet contents are as the following:
ROUTER x 1
Power Adapter x 1
Ethernet Cable x 1
CD x 1
1.3 System Requirements
Before using this ROUTER, verify that you meet the following requirements:
One or more computers, each contains an Ethernet 10/100M Base-T
network interface card (NIC).
A hub or switch, if you are connecting the device to more than four
computers.
For system configuration using the supplied web-based program: A web
browser such as Internet Explorer v5.0 or later, or Netscape v4.7 or
later.

Wireless Router User Manual
4
2 Hardware Description
Front Panel
LED
Color
Function
PWR
Green
On: Power on
Off: No power
FXS1,2
Green
On:A telephone connected to thephoneport has itsreceiver off thehook .
Off: Thehandset of telephoneconnected to thephoneport is on-hook.
WPS
Green
On: WPS connection is established
Blinking: Trying to establish aWPS connection
Off: WPS function is off or no WPS connection
WLAN
Green
On: The wireless module is ready and idle
Blinking: Data transmitting or receiving over WLAN
Off: The wireless function is off
WAN
Green
On: The WAN port has detected a link with an attached device
Blinking: Data isbeing transmitted or received by theWANport
Off: NoWAN link via the WANport
LAN1-4
Green
On: LAN link established and active via LAN port
Blinking: ADSL data activity occurs
Off: No LAN link via LAN port

Wireless Router User Manual
5
Rear panel
Side Panel
WIFI: The switch of wireless function
WPS: A convenient way to set wireless security
Port
Function
FXS1,2
Connect the device to your normal phone
WAN
Connect the device toa optical or optical modem
LAN1,2,3,4
Connect the device to your PC's Ethernet port, or to the
uplink port on your hub/switch, using a RJ-45 cable
USB
Connect the device to your printer
RESET
System reset or reset to factory defaults
ON/OFF
Switch it on or off
PWR
Connect to the supplied power adapter

Wireless Router User Manual
6
3 Hardware Installation
This chapter shows you how to connect Router. Meanwhile, it introduces the
appropriate environment for the Router and installation instructions.
1. Using an Ethernet Cable to connect the WAN port of the ROUTER to a
optical or optical modem.
2. Using an Ethernet Cable to connect the LAN port of the ROUTER to your
LAN or a PC with network card installed.
3. Connect the power cable to the PWR connector on ROUTER, then plug in
the power adapter to the AC power outlet, and then press the on-off button.

Wireless Router User Manual
7
4 PC Configuration Guide
4.1 Local PC Configuration in Windows 95, 98, ME, XP,7
1. In the Windows task bar, click the “Start” button, point to “Settings”, and
then click “Control Panel”.
2. Double-click the “Network” icon.
3. On the “Configuration” tab, select the TCP/IP network associated with your
network card and then click “Properties”.
4. In the “TCP/IP Properties” dialog box, click the “IP Address” tab. Set the IP
address as 192.168.1.x (x can be a decimal number from 2 to 254.) like
192.168.1.2, and the subnet mask as 255.255.255.0.
5. On the “Gateway” tab, set a new gateway as 192.168.1.1, and then click
“Add”.
6. Configure the “DNS” tab if necessary. For information on the IP address of
the DNS server, please consult with your ISP.
7. Click “OK” twice to confirm and save your changes.
8. You will be prompted to restart Windows. Click “Yes”.
4.2 Local PC Configuration in Windows 2000
1. In the Windows task bar, click the “Start” button, point to “Settings”, and
then click “Control Panel”.
2. Double-click the “Network and Dial-up Connections” icon.
3. In the “Network and Dial-up Connections” window, right-click the “Local
Area Connection” icon, and then select “Properties”.
4. Highlight “Internet Protocol (TCP/IP)”, and then click “Properties”.
5. In the “Internet Protocol (TCP/IP) Properties” dialog box, set the IP address
as 192.168.1.x (x can be a decimal number from 2 to 254.), and the subnet
mask as 255.255.255.0 and the default gateway as 192.168.1.1. Then click
“OK”.
6. Configure the “DNS” tab if necessary. For information on the IP address of
the DNS server, please consult with your ISP.
7. Click “OK” twice to confirm and save your changes.

Wireless Router User Manual
8
5 Web-based Management Guide
In order to use the web-based management software, it will be necessary to use
a computer that occupies the same subnet as the Router. The simplest way to
do this for many users will be to use DHCP server that is enabled by default on
the Router.
5.1 LAN setting page
Launch a web browser, such as Internet Explorer, and then use
http://192.168.1.1 to log on to the setting pages.
5.2 Internet Access Configuration
5.2.1 Wide Area Network (WAN) Settings
The Router supports 3 WAN connection types: STATIC, DHCP (Auto config),
PPPoE . from “Network=>Internet.”
1. DHCP (Automatic configuration)
By default, the Router’s Internet Connection Type is set to DHCP (Automatic
configuration), and it should be used only if your ISP supports DHCP or you are
connecting through a dynamic IP address. you need to click Apply/Save button to
save the settings.
Click OK
Enter username ‘admin’
and password ‘admin’

Wireless Router User Manual
9
2. Static IP
If you are required to use a permanent IP address, then select Static.
IP Address: This is the IP address that the Router has, when seen from the
Internet. Your ISP will provide you with the IP address you need to specify
here.
Subnet Mask: This is the Router’s Subnet Mask, as seen by external users
on the Internet (including your ISP). Your ISP will provide you with the Subnet
Mask.
Gateway IP Address: Your ISP will provide you with the Gateway IP
Address.

Wireless Router User Manual
10
Primary DNS Server/Second DNS Server: Your ISP will provide you with at
least one DNS (Domain Name System) Server IP Address.
click the Apply/Save button to save the settings
3. PPPoE
Some ISPs use PPPoE (Point-to-Point Protocol over Ethernet) to establish Internet
connections for end-users. checking with your ISP to see if they use PPPoE. If they
do, you will have to enable it.
PPP User Name: Enter the User Name provided by your ISP.
PPP Password: Enter the Password Provided by your ISP.
PPPoE Service Name:Enter the Service Name Provided by your ISP.
Click the Apply/Save button to save setting.

Wireless Router User Manual
11
5.2.2 LAN Settings
From LAN, Configure the Router’s IP Address and Subnet Mask for LAN
interface. In this page, you can use DHCP (Dynamic Host Configuration Protocol)
to control the assignment of IP addresses on your local network (LAN only).
Item
Description
IP address
This is the IP address that other devices on your local network
will use to connect to the modem.
Subnet mask
This defines the size of your network. The default is
255.255.255.0.
Disable / Enable
DHCP server
The DHCP server assigns an IP addresses from a pre-set pool of
addresses upon request from DHCP client (e.g. your computer).
Do not disable the DHCP server unless you wish to let another
device handle IP address issuance on the local network.
Start / end IP
address
This is the beginning and ending range for the DHCP server
addresses.
Lease time
The amount of time before the IP address is refreshed by the

Wireless Router User Manual
12
DHCP server.
Note: If you want to cancel all modification that you do on the Router, please
select from “ManagementSettingRestore Default Settings” to restore
factory default settings.
5.3 Wireless setting
5.3.1 Basic
Option
Description
Enable
wireless
A checkbox that enables or disables the wireless LAN interfaces. The default
is to enable wireless communications.
Hide Access
Select Hide Access Point to protect the route access point from detection by

Wireless Router User Manual
13
Point
wireless active scans. If you do not want the access point to be automatically
detected by a wireless station, this checkbox should be deselected.
The station will not discover this access point. To connect a station to the
access point, the station must manually add this access point name in it's
wireless configuration.
In Windows XP, go to the Network>Properties function to view all of the
available access points. You can also use other software programs such as
NetStumbler to view available access points.
Clients
isolation
Enable this item if you don’t want your wireless clients to communicate with
each other.
Network
name (SSID)
Enter a name for user’s wireless network here. SSID stands for Service Set
Identifier. This name must be between 1 and 32 characters long. The default
name WLAN.
All wireless clients must either detect the gateway or be configured with the
correct SSID to access the Internet.
BSSID
Displays the gateway's wireless MAC address. (User may need this address
if user’s using WDS or multiple gateways.) Click Apply to save changes.
Country
Drop-down menu that allows selection of specific channel.

Wireless Router User Manual
14
5.3.2 Advanced
Note: After making any changes, click Apply to save.
Warning: The settings shown above are default settings. Changes made to these
items can cause wireless communication problems.
Field
Description
Band
This is the range of frequencies the gateway will use to communicate with
user’s wireless devices.
Channel
Drop-down menu that allows selection of specific channel.
Auto Channel
Timer (min)
The auto channel times length if takes to scan in minutes. Only available for
auto channel mode.

Wireless Router User Manual
15
802.11n/EWC
Select to auto enable or disable 802.11n.
Bandwidth
Select bandwidth. The higher the bandwidth the better the performance will
be
Control
Sideband
Only available for 40MHz. It allows you to select upper sideband or lower
sideband. Sideband refers to the frequency either above (upper sideband)
or below (lower sideband) the carrier frequency, within which fall the
spectral components produced by modulation of a carrier wave.
802.11n Rate
It allows you to select the fixed transmission rate or auto.
802.11n
Protection
Turn off for maximized throughput. Auto for greater security.
Support
802.11n Client
Only
Turn on the option is to only provide wireless access to the clients operating
at 802.11n speeds.
RIFS
Advertisement
Reduced Inter-Frame Spacing (RIFS) is a 802.11n feature that also
improves performance by reducing the amount of dead time required
between OFDM transmissions. Select Off to disable this function or auto to
enable this function.
OBSS
Co-Existance
Coexistence (or not) between 20MHz and 40MHz overlapping basic service
sets (OBSS) in wireless local area networks.
54gTM Rate
This drop-down list lets user specify the wireless communication rate, which
can be Auto (uses the highest rate when possible, or else a lower rate) or a
fixed rate between 1 and 54 Mbps.
Multicast rate
This drop-down list lets user specify the wireless communication rate for
multicast packets, which are sent to more than one destination at a time.
The value can be Auto (uses the highest rate when possible, or else a
lower rate) or a fixed rate between 1 and 54 Mbps.
Basic rate
User has the option of supporting all rates listed in Rate above or using the
1-, 2-Mbps rates, which support only older 802.11b implementations.
Fragmentation
threshold
A threshold, specified in bytes, that determines whether packets will be
fragmented and at what size. On an 802.11 connection, packets that are larger
the fragmentation threshold are split into smaller units suitable for the circuit
size. Packets smaller than the specified fragmentation threshold value are not

Wireless Router User Manual
16
fragmented.
Enter a value between 256 and 2346. If user experience a high packet error
rate, try to increase this value slightly. Setting the fragmentation threshold too
low may result in poor performance.
RTS threshold
This is number of bytes in the packet size beyond which the gateway
invokes its RTS/CTS (request to send, clear to send) mechanism. Packets
larger than this threshold trigger the RTS/CTS mechanism, while the
gateway transmits smaller packets without using RTS/CTS. The default
setting of 2347, which is the maximum, disables the RTS threshold
mechanism.
DTIM interval
A delivery traffic indication message (DTIM), also known as a beacon, is a
countdown informing wireless clients of the next window for listening to
broadcast and multicast messages. When the gateway has broadcast or
multicast messages for its clients, it sends its next DTIM message with this
DTIM interval value. The clients hear the beacons and awaken as needed
to receive the broadcast and multicast messages.
Beacon
interval
The amount of time (in milliseconds) between beacon transmissions, each
of which identifies the presence of an access point. By default, wireless
clients passively scan all radio channels, listening for beacons coming from
access points. Before a client enters power-save mode, it needs the beacon
interval to determine when to wake up for the next beacon (and learn
whether the access point has any messages for it). User can enter any
value between 1and 65535, but the recommended range is 1 - 1000.
Global Max
Clients:
Here you have the option of setting the limit of the number of clients who
can connect to your wireless network.
XPress™
Technology
XPress™ Technology is a feature in which two of our devices can
communicate with each other at twice the normal rate.
54g+ is a technology that achieves higher throughput with frame-bursting. With
54g+ enabled, aggregate throughput (the sum of the individual throughput of
each network client) improves by up to 25% in 802.11g-only networks, and up
to 75% in mixed networks containing both 802.11g and 802.11b equipment.
Transmit
Power
Select the transmitting power of your wireless signal.

Wireless Router User Manual
17
WMM (Wi-Fi
Multimedia)
You can choose to enable or disable this function which allows for priority of
certain data over wireless network.
WMM No
Acknowledge
ment
Refers to the acknowledge policy at the MAC level. Enabling WMM No
Acknowledgement can result in more efficient throughput but higher error rates
in noisy Radio Frequency (RF) environment.
WMM APSD
Automatic Power Save Delivery. Enable this to save power.
5.3.3 Security
This page allows you to configure security features of the wireless LAN interface.
You may set up configuration manually or through WiFi Protected Setup (WPS)
1.Click Security of Wireless item and you’ll see the following page.
2.Configure WPA Pre-shared key as below and click Apply/Save.