Kasda KW5522H User manual

KW5522H Wireless Router
User Manual

Wireless Router User Manual
NOTICE
This document contains proprietary information protected by copyright, and this Manual
and all the accompanying hardware, software, and documentation are copyrighted. All
rights are reserved. No part of this document may be photocopied or reproduced by
mechanical, electronic, or other means in any form.
The manufacturer does not warrant that the hardware will work properly in all
environments and applications, and makes no warranty or representation, either
expressed or implied, with respect to the quality, performance, merchantability, or
fitness for a particular purpose of the software or documentation. The manufacturer
reserves the right to make changes to the hardware, software, and documentation
without obligation to notify any person or organization of the revision or change.
All brand and product names are the trademarks of their respective owners.
© Copyright 2014
All rights reserved.

Wireless Router User Manual
1
CONTENT
1 OVERVIEW................................................................................................................................2
1.1 FEATURES...........................................................................................................................2
1.1.1 Wireless.........................................................................................................................2
1.1.2 Network Protocol & Features.........................................................................................2
1.1.3 FIREWALL ......................................................................................................................2
1.1.4 Management Support....................................................................................................3
1.1.5 Operating System Support .............................................................................................3
1.1.6 Environmental ...............................................................................................................3
1.2 PACKET CONTENTS ...........................................................................................................3
1.3 SYSTEM REQUIREMENTS ...................................................................................................3
1.4 FACTORY DEFAULTS..........................................................................................................4
1.5 WARNINGS AND CAUTIONS ................................................................................................4
2 HARDWARE DESCRIPTION...................................................................................................5
3HARDWARE INSTALLATION.................................................................................................7
4PC CONFIGURATION GUIDE...............................................................................................8
4.1 LOCAL PC CONFIGURATION IN WINDOWS 95, 98, ME, XP,7................................................8
4.2 LOCAL PC CONFIGURATION IN WINDOWS 2000...................................................................8
5 WEB-BASED MANAGEMENT GUIDE....................................................................................9
5.1 LANSETTING PAGE.............................................................................................................9
5.2 NETWORK ACCESS CONFIGURATION.................................................................................10
5.2.1 Internet (WAN) Settings...................................................................................................10
5.2.2 LAN Settings ....................................................................................................................13
5.3 WLAN SETTING................................................................................................................14
5.3.1 Basic Setting....................................................................................................................14
5.3.2 Advanced.........................................................................................................................15
5.3.3 Security ...........................................................................................................................17
5.4 PRINTER SERVER INSTALLAIONS ....................................................................................................19
TROUBLESHOOTING.................................................................................................................. 22

Wireless Router User Manual
2
Overview
Thank you for choosing our product. The KW5522H is a Wireless router, an 802.11n
wireless router and a 4-port switch in one unit, bringing high-speed wireless Internet
connection to a home or office.
1.1 Features
1.1.1 Wireless
Fully IEEE 802.11b & IEEE 802.11g & IEEE 802.11n
compatible.
Wireless data rate up to 300Mbps
Operating in the unlicensed 2.4 GHz ISM band
Multi-SSID
Supports 64/128 bit WEP security and user authentication
1.1.2 Network Protocol & Features
Transparent Bridging
Internet Control Message Protocol (ICMP)
IP Static Routing
Routing Information Protocol (RIP, RIPv2)
Network Address Translation (NAT)
Virtual Server, Port Forwarding
Dynamic Host Configuration Protocol (DHCP)
DNS Relay, DDNS
IGMP Proxy
Simple Network Time Protocol (SNTP)
VPN pass-through (IPSec/PPTP/L2TP)
Parent control
1.1.3 FIREWALL
Built-in NAT

Wireless Router User Manual
3
MAC Filtering
Packet Filtering
Stateful Packet Inspection (SPI)
Denial of Service Prevention (DoS)
DMZ
1.1.4 Management Support
Web Based GUI
Upgrade or update via FTP/HTTP
Command Line Interface via Telnet
Diagnostic Test
Firmware upgradeable for future feature enhancement
1.1.5 Operating System Support
WINDOWS 98/98 SE/ME/2000/XP/VISTA/7
Macintosh
LINUX
1.1.6 Environmental
Operating humidity: 10%-90% non-condensing
Non-operating storage humidity: 5%-95% non-condensing
1.2 Packet Contents
The packet contents are as the following:
ROUTER x 1
Power Adapter x 1
Ethernet Cable x1
CD x 1
1.3 System Requirements
Before using this ROUTER, verify that you meet the following requirements:

Wireless Router User Manual
4
One or more computers, each contains an Ethernet 10/100M/1000M
Base-T network interface card (NIC).
A hub or switch, if you are connecting the device to more than four
computers.
For system configuration using the supplied web-based program: A web
browser such as Internet Explorer v5.0 or later, or Netscape v4.7 or
later.
1.4 Factory Defaults
The device is configured with the following factory defaults:
IP Address: 192.168.1.1
Subnet Mask: 255.255.255.0
Encapsulation: LLC/SNAP-BRIDGING or VC/MUX
VPI/VCI: According to local information
1.5 Warnings and Cautions
Never install telephone wiring during storm. Avoid using a telephone
during an electrical storm. There might be a risk of electric shock from
lightening.
Do not install telephone jacks in wet locations and never use the product
near water.
To prevent dangerous overloading of the power circuit, be careful about
the designed maximum power load ratings. Not to follow the rating
guideline could result in a dangerous situation.
Please note that telephone line on modem must adopt the primary line
that directly outputs from junction box. Do not connect Router to
extension phone. In addition, if your house developer divides a
telephone line to multi sockets inside the wall of house, please only use
the telephone that has connected with the splitter of ADSL Router when
you access the Internet. Under the above condition, if you also install
telephone with anti-cheat-dial device, please pull out this kind of
telephone, otherwise ADSL Router may occur frequently off-line.

Wireless Router User Manual
5
2 Hardware Description
Front Panel
LED
Color
Function
POWER
Green
Off：Power Not Supplied
On：Power Supplied
LAN1 - 4
Green
1000M: The device connected with 1000Mb/s rate.
100M: The The device connected with 100Mb/s rate.
Off：No LAN Link
Blinking：Data is being transmitted through the Interface.
On：LAN Link is established and activ.
WLAN
Green
Off: WLAN is Disable
Blinking: WLAN is with traffic
On: WLAN is On
WPS
Green
Off: WPS function is off
On: WPS connection is on
Blinking: WPS is trying to make a connection
USB
Green
Connect the device to a printer

Wireless Router User Manual
6
Rear panel
Port
Function
WAN
Connect the device to a cable or DSL modem
LAN1,2,3,4
Connect the device to your PC's Ethernet port,
or to the uplink port on your hub/switch, using a
RJ-45 cable
USB
Connect USB device to printer
RESET
System reset or reset to factory defaults
WIFI
The switch of wireless function
WPS
A convenient way to establish wireless connection
ON/OFF
Switch it on or off
POWER
Connect to the supplied power adapter

Wireless Router User Manual
7
3 Hardware Installation
This chapter shows you how to connect Router. Meanwhile, it introduces the
appropriate environment for the Router and installation instructions.
1. Using an Ethernet Cable to connect the WAN port of the ROUTER to a
cable or DSL modem.
2. Using an Ethernet Cable to connect the LAN port of the ROUTER to your
LAN or a PC with network card installed.
3. Connect the power cable to the PWR connector on ROUTER, then plug in
the power adapter to the AC power outlet, and then press the on-off button.

Wireless Router User Manual
8
4 PC Configuration Guide
4.1 Local PC Configuration in Windows 95, 98, ME, XP,7
1. In the Windows task bar, click the “Start” button, point to “Settings”, and
then click “Control Panel”.
2. Double-click the “Network” icon.
3. On the “Configuration” tab, select the TCP/IP network associated with your
network card and then click “Properties”.
4. In the “TCP/IP Properties” dialog box, click the “IP Address” tab. Set the IP
address as 192.168.1.x (x can be a decimal number from 2 to 254.) like
192.168.1.2, and the subnet mask as 255.255.255.0.
5. On the “Gateway” tab, set a new gateway as 192.168.1.1, and then click
“Add”.
6. Configure the “DNS” tab if necessary. For information on the IP address of
the DNS server, please consult with your ISP.
7. Click “OK” twice to confirm and save your changes.
8. You will be prompted to restart Windows. Click “Yes”.
4.2 Local PC Configuration in Windows 2000
1. In the Windows task bar, click the “Start” button, point to “Settings”, and
then click “Control Panel”.
2. Double-click the “Network and Dial-up Connections” icon.
3. In the “Network and Dial-up Connections” window, right-click the “Local
Area Connection” icon, and then select “Properties”.
4. Highlight “Internet Protocol (TCP/IP)”, and then click “Properties”.
5. In the “Internet Protocol (TCP/IP) Properties” dialog box, set the IP address
as 192.168.1.x (x can be a decimal number from 2 to 254.), and the subnet
mask as 255.255.255.0 and the default gateway as 192.168.1.1. Then click
“OK”.
6. Configure the “DNS” tab if necessary. For information on the IP address of
the DNS server, please consult with your ISP.
7. Click “OK” twice to confirm and save your changes.