Katadyn Survivor 06 User manual

Survivor 06
(Model #8013418/#8013419)
GB DE FRA NL DK SWE NOR FIN IT ESP POR

Thank you for purchasing the Katadyn Survivor06 desalinator. It was designed and built to
rigorous specifications by Katadyn Products Inc., to provide fresh water in emergency situ
ations. Please before operating the Survivor, take the short time needed to read this Manual.
This small investment of time will help assure many years of troublefree operation. Be sure
to fill in the enclosed warranty card and return it to us as soon as possible. This is required
to fulfill the terms of your warranty.
Important Precautions
•Avoid sucking in oil, gasoline, or other petroleumbased products – they will quickly destroy
the membrane.
•Avoid drawing water from a confined source. As the salt concentration increases, the unit
will become harder to pump.
•Do not adjust the relief valve. This valve is preset in the factory. Adjusting this valve can dam
age the pump and void your warranty.
• It is normal to detect a slight taste in the fresh water. However, do not drink water with a strong
salt flavor.
• The strainer may eventually clog and need rinsing. If the unit is hard to pump, either the strain
er is clogged or the water is unusually cold or salty.
• During prolonged emergency use, pump the unit for at least 10 minutes each day to keep sea
water from stagnating inside the unit.
• If the unit will not be used again for several days, remove any accessible seawater from it. To
do so, remove the intake strainer and hose from the feed water. Turn the unit upside down, and
pump the handle up and down normally until water stops coming out.
• After the unit has been used, flush the membrane with biocide before storing it again. This will
prevent the growth of bacteria inside the unit. Refer to “Storage” below.
• If the feedwater has an high bacteria content, use biocide daily.
• Store the biocide in a dry, ventilated area.
•IMPORTANT: For your safety, we require that an inspection be completed once a year.
Our regional service centers are trained to perform all necessary quality checks or you can
return the unit to Katadyn for inspection.
IMPORTANT: The Survivor06 is designed for use in emergency conditions.
After it has been used once under such conditions, consult your dealer to deter
mine if any service is required.
English

Product Specifications
The Survivor06 is the smallest handoperated watermaker worldwide, able to produce over 6 gal
lons (~21 liters) of potable water per day from seawater.
A semipermeable membrane inside the unit acts as a molecular filter. When seawater is pressur
ized to 800 psi (~55 bar) by pumping the handle and forced against the membrane, only the water
molecules can pass through: salt molecules are unable to pass, and flow out of the system.
Technology: Reverse Osmosis
Salt rejection: 98.4% on average (96.8% minimum). The desalination degree effect
depends on different influence factors such as pressure, throughput and
the quality of water.
Permeate Flow: 0.89 l/h +/ 15%
Weight: 1.13 kg (2.5 lbs)
Dimensions: 12.7 x 20.3 x 6.4 cm (5” x 8” x 2.5”)
Guarantee: 1 year
Material: Pump: Stainless Steel, plastic
Membrane approved by the US FDA (Food and Drug Administration)
GB

(Figure 11)
Operating Instructions
1. Pull the black intake strainer (and attached double hose) from its storage space inside the
handle. Lower the strainer into the seawater, making sure it will be fully submerged to keep air
from getting into the hose.
2. For now, position the (smaller) freshwater hose so water coming from it will also drain over
board.
3. Place one hand under the end cap and the other over the end of the handle as shown in
Figure 11.
4. Look for the cleanest water source possible. The dirtier the water, the shorter the life of the unit.
5. Pump the handle up and down (as far as it will go in each direction) at a comfortable speed –
about 40 strokes per minute. If water is not drawn in, prime the pump by pumping the handle
rapidly while you hold the unit near or below the water line. Once the seawater is circulating
through the unit, slow to 40 strokes per minute.
6. Once water drips from the freshwater hose, pump at least 80 strokes (two minutes) while pump
ing the water overboard. This will clear the system of biocide solution and salt that passes
through the membrane when not in use. Then insert the freshwater hose into the storage con
tainer, or directly into your mouth.
7. Continue pumping until you get the desired amount of water.

GB
(Figure 12)
Key Components
1. Product Hose (8013208)
2. Cap membrane housing
(8013198)
3. End plug membrane housing
(8013161)
4. Oring (8013190)
5. Oring (qty: 4, 8013239)
6. Membrane module (8013165)
7. Oring, brine seal already installed
8. Plug (8013193)
9. Membrane Housing
(8013156)
10. Weight and strainer
(8013287/8013197)
11. Intake/Reject Hose (8013284)
12. Clamps (8013246/8013203)
13. Two different Orings
(8013243/8013244)
and one seal (8013011)
14. Pump Body Cover (8013160)
15. Screw, handle (qty. 4, 8013019)
16. Left handle (8013164)
17. Right handle (8013163)
18. Screw, cover (qty: 4, 8013200)
19. Pump Body (8013153)
20. Handle pin (qty: 2, 8013188)

Limited Warranty
Your Survivor06 is warranted for one (1) year from the date of purchase against defects in mate
rials and workmanship. Should your Katadyn Survivor prove defective within two years from the
date of purchase, return it to the Katadyn retailer from whom it was purchased. If you do not
receive a satisfactory resolution, contact Katadyn Consumer Relations at 18007556701 for serv
ice assistance. Please retain your purchase receipt as proof of date purchased. This warranty gives
you specific legal rights and you may have other legal rights that vary from state to state.
Katadyn North America
9850 51 st Avenue North
Minneapolis MN 55442, USA
Phone: 8007556701
Fax: 8005480406
www.katadyn.com
[email protected]
Storage (7 days or longer)
The Survivor06 is shipped from the factory with a biocide solution inside, to prevent the growth
of bacteria. After the unit has been operated and before it is stored again, it should be flushed with
biocide as outlined below.
IMPORTANT: Never let the membrane dry out. Be sure to follow these storage instructions.
1. Turn the unit upside down, with the intake strainer out of the water.
2. Fill a suitable container with about a quart (approximate 1 liter) of clean water. Freshwater is
preferable, but clean seawater can be used if freshwater is not available.
3. Mix one spoonful (10 grams) of the biocide with water until dissolved.
4. Place the intake strainer into the biocide solution, and pump until water starts flowing out of the
reject hose (indicating that the membrane housing is filled). Stop pumping immediately after
water begins to flow from the reject hose.
5. If seawater was used to mix the biocide solution, repeat the above procedure with freshwater
as soon as it is available.
6. Rinse any biocide solution off the outside of the unit. Allow the unit to dry completely before
storing.
IMPORTANT: For your safety, we require that the above procedure be completed once a year
(storage temperature < 25°C/77°F). Please be aware to use only biocides supplied by Katadyn
for your product. Other products like chlorinebased products will damage your membrane.
Katadyn Products Inc.
Birkenweg 4
8304 Wallisellen, Switzerland
Phone: [phone]
Fax: [phone]
www.katadyn.ch
[email protected]