KBC eCopper EERN1-LN1-X-MX-B User manual

VC eCopper™
QSG-EERN1-LN1-X-MX-B_Series-Rev2101 www.kbcnetworks.com
Copyright © KBC Networks 2021
Quick Start Guide
EERN1-LN1-X-MX-B
EoU Transmitter & Receiver - 1 UTP Connecter and 1 RJ45
Introduction
The KBC EERN1-LN1-X-MX-B is a fully ruggedized Ethernet over UTP
transmitter and receiver set. This product provides connectivity for one
10/100Mbps IEEE standard electrical copper port over UTP cable. Varying data
rates are supported depending on cable distance and quality. The plug-and-
play design ensures ease of installation with no electrical adjustment needed.
LED indicators are provided to show the operational status of the unit.
The size of the product is suited for fitting inside camera housings and where
space is minimal.
Features
•1 UTP port and 1*10/100M Ethernet port
•UTP data rate >30Mbps (600m)
•12~24VDC power input
•Complete protection design including surge and lightning protection
Downloads
Full specifications, features and additional information can be found on the
KBC website: www.kbcnetworks.com.

Page 2 of 8
General
Check the product upon receipt for any visible damage which may have been
caused during shipping.
Physical Deployment
This equipment must be installed and operated in accordance with
instructions found in this document. Failure to comply with these instructions
will invalidate the warranty.
Application
LAN
EERN1-LN1-T-MX-B EERN1-LN1-R-MX-B
Ethernet UTP
UTPEthernet UTP Ethernet Ethernet
Panel Views
Top View (Transmitter)

Page 3 of 8
Top View (Receiver)
Side View
Network cable panel Ethernet panel
1 - Power input; 2 - LED indicators; 3 - Network cable connector;
4 - Ethernet RJ45 port; 5 –Grounding terminal.
LED
Color
Status
Description
PWR
Green
On
Power supply is normal.
U-LINK
Green
On
EoU connection is normal.
Ethernet
Link/Act
Green
On/Blink
On: Ethernet link is normal.
Blink: Data is active.

Page 4 of 8
Ethernet RJ45 Definition
Pin
Signal
1
TD+
2
TD-
3
RD+
4
N/A
5
N/A
6
RD-
7
N/A
8
N/A
Notes:
★Please use straight-through cable rather than cross-over cable.
8 wires transmission: all 8 wires need to be connected.
4 wires transmission: any 2 wires of PIN 1,2,4 and 5 as “+”, any 2 wires of PIN
3,6,7 and 8 as “-”.
2 wires transmission: any 1 wire of PIN 1,2,4 and 5 as “+”, any 1 wire of PIN
3,6,7 and 8 as “-”.

Page 5 of 8
Dimensions (Unit = mm)
Equipment:
Installation Accessories:

Page 6 of 8
Specifications
Item
Description
Power
Power Input
12/24VDC
Consumption
<2W
Cable
Transmission Medium
Cat5e/6 cable
Operating Frequency
2M~28M
Modulation
Wavelet-OFDM
Transmission Rate
210Mbps (Max.)
Power Negotiation Cycle
1S
Overcurrent
720mA
Overcurrent Protection Time
<2mS
Transmission Distance
*600m
Ethernet Port
Transmission Medium
Cat5e/6
Standard
IEEE802.3, IEEE802.3U
Ethernet Delay
<1mS
Protection
ESD
IEC61000-4-2
Anti-Thunder Protection
IEC61000-4-5 level 3
Operation
Environment
Operating Temperature
-20℃~+70℃
Storage Temperature
-40℃~+85℃
Humidity (Non-Condensing)
0~90%
Mechanical
Dimension (L×W×H)
76mm*37mm*29mm
Material
Aluminum
Color
Black
Weight
0.2Kg
*Transmission distance depends on signal source and cable quality.

Page 7 of 8
Installation Instructions
Please check the following items before installation. If any missing, please
contact the dealer.
⚫EoU transmitter/receiver ------------x1
⚫Wall mounting clamp -----------------x1
⚫QSG/User manual ---------------------x1
⚫Screws ----------------------------------x2
Please follow the installation steps below:
1) Attach the clamp to the wall using the 3X10mm screws.
2) Press the transmitter/receiver into the clamp.

Page 8 of 8
3) Use a network cable to connect the Ethernet port to the powered device
(T) or Ethernet switch (R). Connect the UTP port of the transmitter to
the receiver and use a grounding wire to connect the grounding terminal.
4) Check that the installation is correct and power on the device to be sure
it is operating normally.
Troubleshooting
Please refer to the following information if the device does not work:
⚫Confirm the installation is done according to factory installation
requirements.
⚫Confirm if the RJ45 cable order is following the EIA/TIA568A or 568B
industry standards.
⚫The maximum transmission distance depends on the signal source and
cable quality. Please do not exceed the maximum transmission distance.
⚫Please replace the failed device with a known working unit to determine
if you have a damaged or faulty unit.
⚫If the problem persists, please contact your nearest KBC office or dealer.
Need Help?
Please visit our website www.kbcnetworks.com or contact your nearest KBC
office or dealer.