KEBCO C6 E22 BM User manual

BOOK MOUNT IPC
INSTRUCTIONS FOR USE | C6 E22 BM - C6 E22 BM-RVL
Original Manual
Document 20170810 EN 01

3
PREFACE
Preface
The described hard- and software are developments of the KEB Automation KG. The
enclosed documents correspond to conditions valid at printing. Misprint, mistakes and
technical changes reserved.
Signal words and symbols
Certain operations can cause hazards during the installation, operation or thereafter.
There are safety informations in the documentation in front of these operations. Security
signs are located on the device or machine. A warning contains signal words which are
explained in the following table:
DANGER Dangerous situation, which will cause death or serious injury in case of
non-observance of this safety instruction.
WARNING Dangerous situation, which may cause death or serious injury in case of
non-observance of this safety instruction.
CAUTION Dangerous situation, which may cause minor injury in case of non-ob-
servance of this safety instruction.
NOTICE Situation, which can cause damage to property in case of non-obser-
vance.
RESTRICTION
Is used when certain conditions must meet the validity of statements or the result is
limited to a certain validity range.
Is used when the result will be better, more economic or trouble-free by following
these procedures.
More symbols
► Thisarrowstartsanactionstep.
• / - Enumerations are marked with dots or indents.
=> Cross reference to another chapter or another page.
Note to further documentation.
www.keb.de/nc/search

4
PREFACE
Laws and guidelines
KEB Automation KGconrmswiththeECdeclarationofconformitywiththeCEmark
on the unit name plate, that the device complies with the essential safety requirements.
The EC declaration of conformity can be downloaded on demand via our website. Fur-
therinformationisprovidedinchapter"Certication".
Warranty
The warranty on design, material or workmanship for the acquired device is given in the
current terms and conditions.
Hereyouwillndourcurrenttermsandconditions.
www.keb.de/terms-and-conditions
Furtheragreementsorspecicationsrequireawrittenconrmation.
Support
Through multiple applications not every imaginable case has been taken into ac-
count. If you require further information or if problems occur which are not treated de-
tailed in the documentation, you can request the necessary information via the local
KEB Automation KG agency.
The use of our units in the target products is beyond of our control and therefore
exclusively the responsibility of the machine manufacturer, system integrator or
customer.
Theinformationcontainedinthetechnicaldocumentation,aswellasanyuser-specic
advice in spoken and written and through tests, are made to best of our knowledge and
information about the application. However, they are considered for information only
without responsibility. This also applies to any violation of industrial property rights of a
third-party.
Selection of our units in view of their suitability for the intended use must be done gener-
ally by the user.
Tests can only be done within the application by the machine manufacturer. They
must be repeated, even if only parts of hardware, software or the unit adjustment
are modied.
Copyright
The customer may use the instruction manual as well as further documents or parts from
it for internal purposes. Copyrights are with KEB Automation KG and remain valid in its
entirety.
Other wordmarks or/and logos are trademarks (™) or registered trademarks (®) of their
respectiveownersandarelistedinthefootnoteontherstoccurrence.

5
TABLE OF CONTENTS
Table of Contents
Preface ....................................................................................................................................................3
Signal words and symbols .............................................................................................................3
More symbols.................................................................................................................................3
Laws and guidelines.......................................................................................................................4
Warranty .......................................................................................................................................4
Support .......................................................................................................................................4
Copyright........................................................................................................................................4
Table of Contents ...................................................................................................................................5
List of Figures.........................................................................................................................................8
List of Tables ........................................................................................................................................10
Glossary ................................................................................................................................................ 11
Standards for control & automation...................................................................................................12
1 Basic Safety Instructions............................................ 14
1.1 Target group...................................................................................................................................14
1.2 Transport, storage and proper use .............................................................................................. 14
1.3 Installation......................................................................................................................................15
1.4 Electrical connection ....................................................................................................................15
1.5 Start-up and operation ..................................................................................................................16
1.6 Maintenance...................................................................................................................................16
1.7 Preventive Maintenance................................................................................................................16
1.8 Disposal..........................................................................................................................................17
2 System Description ..................................................... 18
2.1 Key features ...................................................................................................................................18
2.1.1 Isolated Power Supply .......................................................................................................19
2.2 Package ..........................................................................................................................................19
2.3 Front ...............................................................................................................................................20
2.4 Rear.................................................................................................................................................20
2.4.1 Connectors .........................................................................................................................21
2.4.2 Top Connectors ..................................................................................................................22
2.4.3 RVL - Top Connectors / LED ..............................................................................................23
2.4.4 KEB Remote Video Link.....................................................................................................24
2.4.5 LED Signaling.....................................................................................................................25
2.4.6 Buttons Area.......................................................................................................................26
2.4.7 Power Supply / Earth Screw...............................................................................................27
2.4.8 Battery CR2032 3V ............................................................................................................28
2.4.9 CFast..................................................................................................................................29
2.4.10 Micro UPS ........................................................................................................................30
2.4.11 Labels position..............................................................................................................31

6
TABLE OF CONTENTS
3 Installation and connection ........................................ 32
3.1 Preparation for installation...........................................................................................................32
3.1.1 Select the mounting location ..............................................................................................32
3.2 Checking the package contents...................................................................................................32
3.3 Checking the operating conditions ............................................................................................. 32
3.4 Mounting position .........................................................................................................................32
3.5 Damage due to overheating .........................................................................................................32
3.6 Dimensions ....................................................................................................................................33
3.6.1 C6 E22 BM .........................................................................................................................33
3.7 Mounting the device......................................................................................................................35
3.8 Grounding and bonding................................................................................................................37
3.8.1 Power supply insolation......................................................................................................38
3.8.2 Wiring diagram ...................................................................................................................38
3.8.3 Power connection assembly...............................................................................................39
3.8.4 Power on ............................................................................................................................41
3.9 Shutdown .......................................................................................................................................42
4 System Start-up ........................................................... 43
4.1 Additinal notes for Windows Embedded Standard 7 .................................................................43
4.2 EWF implementation in the Windows Embedded Standard 7 images .....................................43
5 KEB Write Filter Manager............................................ 44
5.1 Introduction....................................................................................................................................44
5.2 How EWF works.............................................................................................................................44
5.3 Protectable Volumes .....................................................................................................................44
5.4 KEB EWF conguration................................................................................................................45
5.5 Delivery state of EWF on KEB devices........................................................................................46
5.6 Using KEB_WF_Mgr......................................................................................................................46
5.7 Dependent Volumes ......................................................................................................................48
5.8 Leave the KEB_WF_Mgr ...............................................................................................................50
6 Maintenance and service ............................................ 51
6.1 Battery installtion / removal .........................................................................................................51
6.2 CFast installation / removal.......................................................................................................... 52
6.2.1 Removal .............................................................................................................................52
6.3 Maintaining and cleaning..............................................................................................................52
6.3.1 Procedure...........................................................................................................................53
6.4 Technical support and repairs .....................................................................................................53
6.5 Recycling and disposal.................................................................................................................53
7 Technical specications ............................................. 54
7.1 Block Diagram ...............................................................................................................................54
7.2 Technical data................................................................................................................................ 55

7
TABLE OF CONTENTS
7.2.1 Power supply technical data...............................................................................................57
7.2.2 System power consumption ...............................................................................................58
7.3 Battery technical data ...................................................................................................................58
7.4 Technical support and repairs .....................................................................................................59
8 Certication.................................................................. 60
8.1 Mark of conformity ........................................................................................................................60
8.2 UL certications ............................................................................................................................62

8
LIST OF FIGURES
List of Figures
Figure 1: Isolated Power Supply .....................................................................................................19
Figure 2: Package...........................................................................................................................19
Figure 3: Front detail.......................................................................................................................20
Figure 4: Rear detail........................................................................................................................20
Figure 5: Connector detail............................................................................................................... 21
Figure 6: Top connectors detail ....................................................................................................... 22
Figure 7: Top connectors detail (RVL)............................................................................................. 23
Figure 8: Remote Video Link detail.................................................................................................24
Figure 9: Remote Video Link detail.................................................................................................24
Figure 10: LED signaling detail .........................................................................................................25
Figure 11: Buttons area detail...........................................................................................................25
Figure 12: Buttons area detail...........................................................................................................26
Figure 13: Buttons area detail...........................................................................................................26
Figure 14: Power Supply area detail.................................................................................................27
Figure 15: Power Supply area detail.................................................................................................27
Figure 16: Power Supply area detail.................................................................................................27
Figure 17: Battery slot detail .............................................................................................................28
Figure 18: CFast slot detail ...............................................................................................................29
Figure 19: Labels postion.................................................................................................................. 31
Figure 20: C6 E22 BM.......................................................................................................................33
Figure 21: C6 E22 BM.......................................................................................................................34
Figure 22: C6 E22 BM.......................................................................................................................34
Figure 23: Wall mounting procedure .................................................................................................35
Figure 24: Wall mounting procedure .................................................................................................35
Figure 25: Wall mounting procedure .................................................................................................36
Figure 26: Wall mounting procedure .................................................................................................36
Figure 27: Wall mounting procedure .................................................................................................36
Figure 28: Power supply diagramm ..................................................................................................37
Figure 29: Power supply diagramm ..................................................................................................37
Figure 30: Grounding detail...............................................................................................................38
Figure 31: Power supply connection detail .......................................................................................39
Figure 32: Power connector assembly.............................................................................................. 39
Figure 33: Power connector assembly.............................................................................................. 39
Figure 34: Power connector assembly.............................................................................................. 39
Figure 35: Power connector assembly.............................................................................................. 40
Figure 36: Cup installation ................................................................................................................40
Figure 37: Cup installtion ..................................................................................................................40
Figure 38: Cup installation ................................................................................................................40
Figure 39: Power connector assembly.............................................................................................. 41
Figure 40: Screwdriver detail ............................................................................................................41
Figure 41: Power on sequence .........................................................................................................42
Figure42: EWFconguration ...........................................................................................................45
Figure 43: Delivery state ...................................................................................................................46

9
LIST OF FIGURES
Figure 44: Icon on the desktop..........................................................................................................46
Figure 45: Elevated rights .................................................................................................................47
Figure 46: Program’s GUI .................................................................................................................47
Figure 47: Commit.............................................................................................................................49
Figure 48: Commit and Disable.........................................................................................................49
Figure 49: Clear Command............................................................................................................... 49
Figure 50: Neglect pending boot commands ....................................................................................50
Figure 51: Battery installation / removal............................................................................................ 51
Figure 52: Battery installation / removal............................................................................................ 51
Figure 53: Battery installation / removal............................................................................................ 51
Figure 54: Battery installation / removal............................................................................................ 51
Figure 55: CFast installation / removal..............................................................................................52
Figure 56: CFast installation / removal..............................................................................................52
Figure 57: Block diagram ..................................................................................................................54
Figure 58: Battery CR2032 detail...................................................................................................... 58
Figure 59: Battery performance ........................................................................................................59
Figure 60: Battery dimensions ..........................................................................................................59

10
LIST OF TABLES
List of Tables
Table 1: Micro UPS data................................................................................................................ 30
Table 2: Protectable Volumes........................................................................................................44
Table 3: Technical data .................................................................................................................. 55
Table 4: Options.............................................................................................................................56
Table 5: Power supply technical data ............................................................................................57
Table 6: System power consumption............................................................................................. 58
Table 7: Battery technical data ......................................................................................................59