Kelkay Easy Fountain 45004L User manual

Easy Fountain Instructions
45004L - Trickling Tree Pots
STAGE 1
Position the water feature onto a secure and level surface.
STAGE 2
STAGE 3
STAGE 4
STAGE 5
ELECTRICAL SAFETY: If outdoors the outlet must be
waterproof. We recommend the use of a residual current device
(GFI) Ground Fault Interrupter (available from all good D.I.Y.
stores) when connecting the fountain to the electric supply.
PUMP FLOW: The pump flow
can be adjusted with the
regulator, this is found on the
inlet of the pump. We
recommend starting with the
flow regulator fully open and
then adjusting down if required.
STAGE 6
Connect the pump and LED adaptor to a mains power outlet.
As shown in the diagram above locate the access cavity / water reservoir at the back of the water
feature. Reach inside the feature and carefully bring out the internal water pipe and the LED cables.
The transformer should never be submerged or stood in water.
Please note the transformer will get hot while in use, this is normal.
Please read the assembly and pump operating instructions carefully and observe the safety
instructions.
Carefully fill the feature with sufficient water taking care to ensure the pump is fully submerged.
Position the pump and excess wires inside the access cavity / water reservoir ensuring that the long
pump and LED wire extend out through the opening. Replace the back trapdoor to cover the
opening.
Attach the internal water pipe to the pump outlet and connect the internal LED wires to the adaptor
plug provided.
www.kelkay.com

easyfountain®
Aftercare Information
www.kelkay.com
• Clean and top-up the water on a regular basis.
• To empty the fountain of water for cleaning or for
winter care:
Smaller fountains (that are light enough to be lifted)
the water can be emptied by simply inverting the
fountain and letting the water pour away through a
suitable drain or sink.
Larger (heavier) fountains - water can be removed
by using a large sponge or by purchasing a simple
syphon pipe available from aquatic supply stores.
• Always shut off the power before cleaning and
maintaining the fountain or pump.
Please note: The easyfountain®aftercare range is only available in the UK
and Republic of Ireland. Please check with your nearest stockist for availability.
Caring for your fountainCleaning your fountain
Troubleshooting
Winter care
The easyfountain®aftercare range includes products to
help care for your fountain. Please see the table below
for more information.
Fountain Algae Stopper 385g
• Easy to use
• Removes and prevents algae and bacteria
• Will not harm animals and birds
Fountain Grime and Lime Cleaner 500ml
• Easy to use
• Removes dirt from your water feature
• Limescale buster
Fountain One Shot Algae Remover 100g
• Easy to use
• Removes algae and bacteria
• Stops slime build up
Fountain Citronella Water Scent 125ml
• Easy to use
• Clean and fresh scent
• Helps to repel insects
Fountain Shine Spray 500ml
• Easy to use
• Helps preserve radiance
• Leaves a smear free shine
Guidelines to help protect your easyfountain®:
• If possible, bring your water feature indoors
eg. garage or shed.
• Drain the fountain of all water. If water freezes within
the fountain, this can cause damage.
• If your fountain is left outside and drained of all water,
a Kelkay easyfountain® cover can be purchased to
cover the entire fountain however we cannot
guarantee that it will protect your fountain from
winter damage.
Pumps
• Check the water is covering the pump by at least 5cm.
• Check the flow dial on the pump to ensure the correct
“flow” for the fountain is set.
• Check to see if it is running if it is then it is probably
blocked.
• Clear the pipe and impeller from blockages.
• Check the fuse in the plug.
Lights/Transformers
• If the lights and the pump are not working it is likely the
transformer has failed. If the product is within the
warranty period and misuse has not occurred a
replacement part can be issued providing a proof of
purchase is supplied.
• Flickering lights are caused by a build-up of algae and
lime scale on the connectors between the transformer
and the lights. This is not covered by the warranty.
Replacement parts can be purchased from Kelkay LTD.
• If the lights stop working they are available to purchase
from Kelkay LTD. Light bulbs are not covered under
the warranty.
• Individual L.E.D lights are not replaceable but can be
replaced as a set.
Leaks/Loss of Water
• Overfilled - make sure the water reservoir is not
overfilled. Remove water if necessary.
• Pump Flow Rate - check the pump and reduce the
flow rate if required.
• Level - ensure the fountain is completely level.
• Natural evaporation, weather elements and wildlife
will also affect the fountain water level on a daily
basis. Top up your fountain as required.
Main Body & Paintwork
• Do not confuse limescale residue with fading paint -
this is not a fault and in most cases the fountain
needs cleaning.
• Paint peeling will occur if the fountain has been left
outside in the frost and will not be covered by the
warranty.
• Parts broken off the main body while in use are
usually caused by bad weather conditions and not
covered by the warranty.