Kelvinator KSV26CRC User manual

Inverter Room Air Conditioner
Installation Manual
KSV26CRC, KSV26HRC, KSV35CRC,
KSV35HRC, KSV53HRC, KSV62HRC,
KSV70CRC, KSV70HRC, KSV80HRC
Refrigerant R410A

caution
1 The unit must only be installed by a qualified refrigeration
mechanic and electrical work carried out by a qualified
electrician according to local or government regulations
and in compliance with this manual.
2 Before installation, please contact a qualified air
conditioner installer. If the unit is not installed by a
qaulified air conditioner installer, the malfunction may
not be solved due to faulty installation.
3 If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
4 The appliance must be positioned so that the plug
is accessible.
5 The temperature of refrigerant circuit will be high,
please keep the interconnection cable away from the
copper tube.
6 This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities,or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
7 For appliances with type Y attachment,the instructions
shall contain the substance of the following. If the
supply cord is damaged,it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
warning
Before obtaining access to terminals, all supply circuits must
be disconnected.
Please read this installation manual and the user manual
before installation and carefully store in a handy place for
later reference. Inside you will find many helpful hints on how
to install and test the air conditioner properly.
Electrical work must be installed by a licensed electrician.
Be sure to use the correct rating of the power plug and main
circuit for the model to be installed.
Incorrect installation due to ignoring this instruction will
cause harm or damage, and the seriousness is classified by
the following indications.
Meanings of symbols used in this manual are shown below:
warning
This symbol indicates information concerning your
personal safety
caution
This symbol indicates information on how to avoid
damaging the appliance
tips and information
This symbol indicates tips and information about
use of the appliance
environmental tip
This symbol indicates tips and information about
economical and ecological use of the appliance
This symbol indicates never to do this
This symbol indicates always do this
Important safety instructions Notice for installation
2 Contents Kelvinator Air Conditioning
Congratulations and thank you for choosing our Inverter
Speed Split room air conditioner. We are sure you will find
your new air conditioner a pleasure to use. Before you use
the air conditioner, we recommend that you read through
the entire user manual, which provides the description of
the air conditioner and its functions.
To avoid the risks that are always present when you use an
electrical appliance, it is important that the air conditioner
is installed correctly and that you read the safety instructions
carefully to avoid misuse and hazards.
We recommend that you keep this instruction booklet
for future reference and pass it on to any future owners.
After unpacking the air conditioner please check it is not
damaged. If in doubt, do not use the air conditioner but
contact your local Electrolux Customer Care Centre.
environmental tip
Information on disposal for users
• Most of the packing materials are recyclable.
Please dispose of those materials through your local
recycling depot or by placing them in appropriate
collection containers.
• If you wish to discard this air conditioner, please contact
your local authorities and ask for the correct method
of disposal.
caution
• The air conditioner is not intended for use by young
children or infirmed persons without supervision.
• Young children should be supervised to ensure that
they do not play with the air conditioner.
• Contact an authorised installer for installation of this unit.
• Contact an authorised service technician for repair or
maintenance of this unit.
• If the power cord is to be replaced, replacement work
shall be performed by authorised personnel only.
• Installation work must be performed in accordance
with the national wiring Standards by authorised
personnel only.
Conditions of use
This appliance is intended to be useed in household and
similar applications such as:
• Staff kitchen areas in shops, offices and other working
environments
• Farm houses
• By clients in hotels, motels, and other residential
type environments
• Bed and breakfast type environments
Contents............................................................................ 2
Safety precautions ............................................................ 3
Notice for installation ....................................................... 3
Installation drawing .......................................................... 5
Installation of indoor unit ................................................. 6
Refrigerant pipe connection ............................................. 8
Installation of outdoor unit............................................... 9
Check after installation and operation test.................... 10
Installation and Maintenance of HEPA Filter .................. 10
Warranty.......................................................................... 11
Congratulations Contents
Kelvinator Air Conditioning Important safety instructions/Notice for installation 3

Kelvinator Air Conditioning installation drawing 54 Notice for installation Kelvinator Air Conditioning
Safety Precautions for Electric Appliances
1 A dedicated power supply circuit should be used for
products not supplied with a service cord and plug in
accordance with local electrical safety regulations.
3 The unit must be reliably earthed and connected to
the special earth device by the qualified electrician.
4 The circuit breaker must have the functions of magnetic
tripping and heat tripping to prevent short circuit
and overload.
5 The appliance shall be installed in accordance with
national wiring regulations.
6 Including an circuit breaker with suitable capacity, please
note the following table.
Model Circuit Breaker (Amps)
KSV26CRC 10
KSV26HRC 10
KSV35CRC 10
KSV35HRC 10
KSV53HRC 15
KSV62HRC 15
KSV70CRC 20
KSV70HRC 20
KSV80HRC 20
Note:
• Make sure the live wire, neutral wire and earth wire in
the power socket are properly connected.
• Inadequate or incorrect electrical connections may cause
electric shock or fire.
Earthing Requirements
1 Air conditioner is type I electric appliance. Please ensure
the unit is reliably earthed.
2 The yellow-green wire in air conditioner is the earthing
wire which can not be used for other purposes. Improper
earthing may cause electric shock.
3 The earth resistance should accord to the national
wiring regulation.
4 The user's power must have reliable earthing terminal.
Do not connect the earthing wire with the following:
1. Water pipe
2. Gas pipe
3. Contamination pipe
Installation drawing
Installation Site Instructions
A proper installation site is vital for correct and efficient
operation of the unit. Avoid the following sites where:
• strong heat sources, vapours, ammable gas or volatile
liquids are emitted.
• high-frequency electro-magnetic waves are generated
by radio equipment, welders or medical equipment.
• salt-laden air prevails (such as close to coastal areas).
• the air is contaminated with industrial vapours and oils.
• the air contains sulphurous gas such as in hot spring
zones.
• corrosion or poor air quality exists.
Installation Site of Indoor Unit
1 The air inlet and outlet should be away from the
obstructions. Ensure the air can be blown through the
whole room.
2 Select a site where the condensing water can be
easily drained out, and where it is easily connected for
the outdoor unit.
3 Select a place where it is out of reach of children.
4 Select the place where the wall is strong enough to
withstand the full weight and vibration of the unit.
5 Be sure to leave enough space to allow access for routine
maintenance. The installation site should be 2m or more
above the oor.
6 Select a place about 1m or more away from a TV set or
any other electric appliance.
7 Select a place where the filter can be easily taken out.
8 Make sure that the indoor unit is installed in accordance
with installation dimension instructions (refer to page 5).
9 Do not use the unit in the laundry or by swimming
pool etc.
Installation Site of Outdoor Unit
1 Select a site where noise and outow air emitted by unit
will not annoy neighbors.
2 Select a site where there is sufficient ventilation.
3 Select a site where there is no obstruction blocking the
inlet and outlet.
4 The site should be able to withstand the full weight
and vibration of the unit.
5 Select a dry place, but do not expose the unit to direct
sunlight or strong wind.
6 Make sure that the outdoor unit is installed in accordance
with the installation instructions, and is convenient for
maintenance and repair.
7 The height difference between indoor and outdoor units
complies with the table on page 8.
8 Select a place where it is out of reach of children.
Space to the ceiling
Space to the wall
Space to the wall
Air outlet side
Space to the floor
Above
Above
15cm Above 15cm Above
300cm 200
cm
15cm
Above
The dimensions of the minimum in between
If these dimensions are not adhered to the air conditioner will
not perform to specification, may not be able to be serviced
and the warranty may be voided.
the installation must allow for reasonable access
space necessary for properinstallation of the
unit include the minimumpermissible distances
to adjacent parts.
●
Space to the wall
200cm Above
30cm Above
Space to the obstruction
Air outlet side
evob
50cm A
Space to the wall
Air inlet side
30cm Above
50cm Above

2 Insert the piping-hole sleeve into the hole to prevent the
connection piping and wiring from being damaged when
passing through the hole.
Ø Ø
55/ 65
Indoor Outdoor
Wall pipe Seal pad
Installation of Drain Hose
1 Connect the drain hose to the outlet pipe of the
indoor unit. Bind the joint with rubber belt.
drain hose
outlet pipe of
indoor unit
outlet pipe of
indoor unit
rubber belt
2 Put the drain hose into insulating tube.
insulating tube
drain hose
outlet pipe of
indoor unit
rubber belt
3 Wrap the insulating tube with wide rubber belt to
prevent the shift of insulating tube. Slant the drain
hose downward slightly for smooth drainage of
condensing water.
outlet pipe of
indoor unit
insulating tube
connected
rubber belt
Note:
The insulating tube should be connected reliably with the
sleeve outside the outlet pipe. The drain hose should be
slanted downward slightly, without distortion, bulge or
uctuation. Do not put the outlet in the water.
Installation of indoor unit
Installation of Mounting Plate
1 The mounting plate should be installed horizontally.
As the water tray's outlet for the indoor unit is two-way
type, during installation, the indoor unit should slightly
slant to water tray's outlet for smooth drainage of
condenser water.
2 Fix the mounting plate on the wall with screws.
3 Be sure that the mounting plate has been fixed firmly
enough to withstand about 60kg. Meanwhile, the weight
should be evenly shared by every screw.
Note: All dimensions are in mm.
2.6kW UNIT:
3.5kW UNIT:
Ø55 Ø55
34.5
34.5
316
6.2 kW, 7.0 kW and 8 kW UNITS:
5.2kW UNIT:
Drill Piping Hole
1 Slant the piping hole on the wall slightly downward to
the outdoor side.
Piping hole Units
(55) 2.6 kW, 3.5 kW and 5.3kW
(65) 6.2 kW, 7.0 kW and 8 kW
6 Installation instructions Kelvinator Air Conditioning Kelvinator Air Conditioning Installation instructions 7
Installation of indoor and outdoor electric wires
1 Open the front panel.
2 Remove the wiring cover connect and fix power
connection cord to the terminal board as shown in Fig 6.
3 Make the power connection cord pass through the hole
at the back of indoor unit.
4 Reinstall the cord anchorage and wiring cover.
5 Reinstall the front panel.
For 2.6kW and 3.5kW units:
yellow-
brown
black
blue
2
N(1) 3
Wiring Cover
outdoor unit connection
green
For 5.3kW, 6.2kW, 7.0kW and 8kW units:
yellow-
brown
black
blue
2
N(1) 3
Wiring Cover
outdoor unit connection
green
Note:
All wires between indoor and outdoor units must be
connected by a qualified electric contractor.
• Electric wires must be connected correctly. Improper
connection may cause malfunction.
• Tighten the terminal screws tightly.
• After tightening the screws, pull the wire slightly to
confirm whether it's firm or not.
• Make sure that the electric connections are earthed
properly to prevent electric shock.
• Make sure that all wiring connections are secure and the
cover plates are reinstalled properly. Poor installation
may cause fire or electric shock.
Installation of Indoor Unit
• The piping can be output from right, right rear, left or
left rear.
1 When routing the piping and wiring from the left or right
side of indoor unit, cut off the tailings from the chassis
when necessary (As shown in Fig.1)
a. Cut off the tailings 1 when routing the wiring only;
b. Cut off the tailings 1 and tailings 2 when routing both
the wiring and piping.
2 Take out the piping from body case, wrap the piping,
power cords, drain hose with the tape and then make
them pass through the piping hole. (As shown in Fig.2)
3 Hang the mounting slots of the indoor unit on the
upper hooks of the mounting plate and check if it is
firm enough. (As shown in Fig.3)
4 The installation site should be 2m or more above
the oor.
Right
Right rear
Fig.2
Left rear
Left
Fig.1
Tailing 1
Tailing 2
Finally wrap it
with tape
Gas side piping
insulation
Water drainage pipe
Liquid side
Piping insulation
Gas side pipe External connection
electric wire
Liquid side piping
Fig.3
Mounting
plate
Fixing hook Mounting
plate
Installation of Connection Pipe
Align the center of the piping are with the related valve.
Screw in the are nut by hand and then tighten the nut with
spanner and torque wrench by referring to the following:
Hex nut diameter Tightening torque (N·m)
615~20
9.52 30~40
12 45~55
16 60~65
19 70~75
For installations with connecting pipes greater than 5m,
additional refrigerant is required at the following rates per
extra metre of pipe.
2.6 kW & 3.5 kW Reverse cycle 20g/m
2.6 kW & 3.5kW Cooling only 15g/m
5.3 kW & 6.2 kW Reverse cycle 50g/m
7.0 kW Cooling only, 7.0 kW & 8.0 kW Reverse cycle 50g/m
bulge
distortion
Flooded

Kelvinator Air Conditioning installation instructions 98 installation instructions Kelvinator Air Conditioning
Spanner Torque
wrench
Piping
Taper nut
Indoor unit piping
Model Suction
(mm) Discharge (mm) Maximum lenght Maximum Height
KSV26CRC 6.4 (1/4") 9.5 (3/8") 15 10
KSV26HRC 6.4 (1/4") 9.5 (3/8") 15 10
KSV35CRC 6.4 (1/4") 9.5 (3/8") 20 10
KSV35HRC 6.4 (1/4") 9.5 (3/8") 20 10
KSV53HRC 6.4 (1/4") 16.0 (5/8") 25 10
KSV62HRC 6.4 (1/4") 16.0 (5/8") 20 10
KSV70CRC 6.4 (1/4") 16.0 (5/8") 25 10
KSV70HRC 6.4 (1/4") 16.0 (5/8") 25 10
KSV80HRC 6.4 (1/4") 16.0 (5/8") 25 10
Note:
Connect the connection pipe to indoor unit at first and then
to outdoor unit. Handle piping bending with care. Do not
damage the connection pipe. Ensure that the joint nut is
tightened firmly, otherwise, it may cause leakage.
Installation of outdoor unit
Electric wiring
1 Remove the handle on the right side plate of
outdoor unit.
2 Take off wire cord anchorage. Connect and fix power
connection cord to the terminal board. Wiring should fit
that of indoor unit.
3 Fix the power connection cord with wire clamps and then
connect the corresponding connector.
4 Confirm if the wire has been fixed properly.
5 Reinstall the handle.
For 2.6kW and 3.5kW units:
Handle
yellow- brown
black
blue
2
N(1) 3
indoor unit connection
green
For 5.3kW, 6.2kW, 7.0kW and 8kW units:
Handle
yellow- brown
black
blue
2
N(1)
3
indoor unit connection
green
Air Purging and Leakage Test
1 Connect charging hose of manifold valve to charge end
of low pressure valve (both high/low pressure valves
must be tightly shut).
2 Connect joint of charging hose to vacuum pump.
3 Fully open the handle of Lo manifold valve.
4 Open the vacuum pump for vacuumization. At the
beginning, slightly loosen joint nut of low pressure valve
to check if there is air coming inside. (If noise of vacuum
pump has been changed, the reading of multimeter is 0)
Then tighten the nut.
5 Keep vacuuming for more than 15mins and make sure the
reading of multi-meter is -1.0 105pa (-76cmHg).
6 Fully open high/low pressure valves.
7 Remove charging hose from charging end of low
pressure valve.
8 Tighten lid of low pressure valve. (As shown in below)
Multimeter
-76cmHg
Lo Handle
Charging hose
Hi handle
Charging hose
Low pressure valve
Manifold
Valve
Vacu um pump
Outdoor Condensate Drainage (only for Heat pump unit)
During heating operation, the condensate and defrosting
water should be drained out reliably through the drain hose.
Install the outdoor drain connector in a 25mm hole on the
base plate and attach the drain hose to the connector so
that the waste water formed in the outdoor unit can be
drained out. The hole diameter 25mm must be plugged.
Whether to plug other holes will be determined by the
installer according to actual conditions.
Drain-water hole
Bottom frame
Drain plug
Hose (available commercially,
inner diameter 16mm)
Drain connecter
Outer diam. (mm) A(mm)
Max. Min.
φ6.35 1.3 0.7
φ9.53 1.6 1.0
φ12.7 1.8 1.0
φ16.0 2.4 2.2
Bar
Copper pipe
Clamp handle Red arrow mark
Cone
Yoke
Handle
Bar
"A"
Tightening Connection
• Align the center of the pipes.
• Sufciently tighten the are nut with ngers, and
then tighten it with a spanner and torque wrench
as shown below.
Indoor unit tubing Flare nut Pipings
Outer diam. Tightening torque
(Kg.m)
Additional Tightening
Torque (Kg.m)
φ6.35 1.6 2.0
φ9.53 3.0 3.5
φ12.7 5.0 5.5
φ16.0 7. 5 8.0
caution
• Excessive torque can break nut depending on
installation conditions.
E: Check
• Compare the ared work with the adjacent diagram.
• If are is found to be defective, cut off the ared section
and do aring work again.
Smooth all round
Improper flaring
Even length
all round
Refrigerant pipe connection
1 Flaring work
Main cause for refrigerant leakage is due to defects in
the aring work. Carry out correct aring work using the
following procedure:
Oblique
90 C Roughness
Burr
A: Cut the pipes and the cable.
1 Use the piping kit accessory (if applicable) or pipes
purchased locally.
2 Measure the distance between the indoor and the
outdoor unit.
3 Cut the pipes a little longer than the measured distance.
4 Cut the cable 1.5m longer than the pipe length.
B: Burr removal
1 Completely remove all burrs from the cut cross section
of pipe/tube.
2 Face the end of the copper pipe/tube in a downward
direction as you remove burrs in order to avoid burrs
dropping into the tubing.
Pipe
Reamer
Face down
caution
C: Putting are nut on
Remove are nuts attached to indoor and outdoor unit,
then put them on pipe/tube having completed burr removal
Note: It is not possible to put them on after flaring work.
Flare nut
Copper tube
D: Flaring work
• Carry out aring work using aring tool as shown below.
• Firmly hold copper pipe in a die according to the
dimension shown in the table below.

10 Kelvinator Air Conditioning installation instructions Kelvinator Air Conditioning warranty 11
This document sets out the terms and conditions of the product
warranties for Electrolux Appliances. It is an important document.
Please keep it with your proof of purchase documents in a safe place
for future reference should you require service for your Appliance.
1. Inthiswarranty
 (a) ‘acceptablequality’asreferredtoinclause10ofthiswarrantyhas
thesamemeaningreferredtointheACL;
 (b) ‘ACL’meansTradePracticesAmendment(AustralianConsumer
Law)Act(No.2)2010;
 (c) ‘Appliance’meansanyElectroluxproductpurchasedbyyou
accompaniedbythisdocument;
 (d) ‘ASC’meansElectrolux’authorisedservicedcentres;
 (e) ‘Electrolux’meansElectroluxHomeProductsPtyLtdof163
O’RiordanStreet,Mascot,NSW2020,ABN51004762341in
respectofAppliancespurchasedinAustraliaandElectrolux(NZ)
Limitedof3-5NiallBurgessRoad,MountWellington,inrespect
ofAppliancespurchasedinNewZealand;
 (f) ‘majorfailure’asreferredtoinclause10ofthiswarrantyhasthe
samemeaningreferredtointheACLandincludesasituationwhen
anAppliancecannotberepairedoritisuneconomicforElectrolux,
atitsdiscretion,torepairanApplianceduringtheWarrantyPeriod;
 (g) ‘WarrantyPeriod’means:
  (i) wheretheApplianceisusedforpersonal,domesticorhousehold
use(i.e.normalsinglefamilyuse)assetoutintheinstruction
manual,theApplianceiswarrantedagainstmanufacturing
defectsinAustraliafor24monthsandinNewZealandforthe
periodof24months,followingthedateoforiginalpurchase
oftheApplianceandafurther36months;inAustraliaifthereis
evidenceprovidedtoElectroluxthattheappliancewasinstalled
byalicensedroomairconditionerinstaller;inNewZealandif
thereisevidencethattheAppliancewasinstalledaccordingto
theElectroluxinstallationguidelineswhichcanbeinspectedon
theKelvinatorwebsite;
  (ii) wheretheApplianceisusedforcommercialpurposes(including
beingusedtodirectlyassistabusinessorwheretheApplianceis
usedinamulti-familycommunalorsharetypeenvironment),the
Appliancewillthenbewarrantedagainstmanufacturingdefects
inAustraliafor3monthsandinNewZealandfor0months,
followingthedateoforiginalpurchaseoftheAppliance.
 (h) ‘you’meansthepurchaseroftheAppliancenothavingpurchased
theApplianceforre-sale,and‘your’hasacorrespondingmeaning.
2. ThiswarrantyonlyappliestoAppliancespurchasedandusedinAustralia
orNewZealandandisinadditionto(anddoesnotexclude,restrict,or
modifyinanyway)anynon-excludablestatutorywarrantiesinAustralia
orNewZealand.
3. DuringtheWarrantyPeriodElectroluxoritsASCwill,atnoextracharge
ifyourApplianceisreadilyaccessibleforservice,withoutspecial
equipmentandsubjecttothesetermsandconditions,repairorreplace
anypartswhichitconsiderstobedefective.ElectroluxoritsASCmay
useremanufacturedpartstorepairyourAppliance.You agreethat
anyreplacedAppliancesorpartsbecomethepropertyofElectrolux.
Thiswarrantydoesnotapplytolightglobes,batteries,ltersorsimilar
perishableparts.
4. PartsandAppliancesnotsuppliedbyElectroluxarenotcoveredby
thiswarranty.
5. Youwillbearthecostoftransportation,travelanddeliveryofthe
AppliancetoandfromElectroluxoritsASC.Ifyouresideoutsideofthe
servicearea,youwillbearthecostof:
 (a) travelofanauthorisedrepresentative;
 (b) transportationanddeliveryoftheAppliancetoandfromElectroluxor
itsASC,
Inallinstances,unlesstheApplianceistransportedbyElectroluxoran
Electroluxauthorisedrepresentative,theApplianceistransportedatthe
owner’scostandriskwhileintransittoandfromElectroluxoritsASC.
6. Proofofpurchaseisrequiredbeforeyoucanmakeaclaimunder
thiswarranty.
7. Youmaynotmakeaclaimunderthiswarrantyunlessthedefectclaimed
isduetofaultyordefectivepartsorworkmanship.Electroluxisnotliable
inthefollowingsituations(whicharenotexhaustive):
 (a) theApplianceisdamagedby:
  (i) accident
  (ii) misuseorabuse,includingfailuretoproperlymaintainorservice
  (iii) normalwearandtear
  (iv) powersurges,electricalstormdamageorincorrectpowersupply
  (v) incompleteorimproperinstallation
  (vi) incorrect,improperorinappropriateoperation
  (vii)insectorvermininfestation
  (viii)failuretocomplywithanyadditionalinstructionssuppliedwiththe
Appliance;
 (b) theApplianceismodiedwithoutauthorityfromElectroluxinwriting;
 (c) theAppliance’sserialnumberorwarrantysealhasbeenremoved
ordefaced;
 (d) theAppliancewasservicedorrepairedbyanyoneotherthan
Electrolux,anauthorisedrepairerorASC.
8. Thiswarranty,thecontracttowhichitrelatesandtherelationship
betweenyouandElectroluxaregovernedbythelawapplicablewhere
theAppliancewaspurchased.WheretheAppliancewaspurchasedin
NewZealandforbusinesspurposestheConsumerGuaranteeActdoes
notapply.
9. To theextentpermittedbylaw,Electroluxexcludesallwarrantiesand
liabilities(otherthanascontainedinthisdocument)includingliabilityfor
anylossordamagewhetherdirectorindirectarisingfromyourpurchase,
useornonuseoftheAppliance.
10.ForAppliancesandservicesprovidedbyElectroluxinAustralia,the
AppliancescomewithaguaranteebyElectroluxthatcannotbeexcluded
undertheAustralianConsumerLaw.Youareentitledtoareplacementor
refundforamajorfailureandforcompensationforanyotherreasonably
foreseeablelossordamage.YouarealsoentitledtohavetheAppliance
repairedorreplacediftheAppliancefailstobeofacceptablequalityand
thefailuredoesnotamounttoamajorfailure.Thebenetstoyougiven
bythiswarrantyareinadditiontoyourotherrightsandremediesundera
lawinrelationtotheAppliancesorservicestowhichthewarrantyrelates.
11.AtalltimesduringtheWarrantyPeriod,Electroluxshall,atitsdiscretion,
determinewhetherrepair,replacementorrefundwillapplyifan
Appliancehasavalidwarrantyclaimapplicabletoit.
12.ForAppliancesandservicesprovidedbyElectroluxinNewZealand,
theAppliancescomewithaguaranteebyElectroluxpursuanttothe
provisionsoftheConsumerGuaranteesAct,theSaleofGoodsActand
theFairTradingAct.
13.Toenquireaboutclaimingunderthiswarranty,pleasefollowthesesteps:
 (a) carefullychecktheoperatinginstructions,usermanualandtheterms
ofthiswarranty;
 (b) havethemodelandserialnumberoftheApplianceavailable;
 (c) havetheproofofpurchase(eganinvoice)available;
 (d) telephonethenumbersshownbelow.
14.Youacceptthatifyoumakeawarrantyclaim,ElectroluxanditsASC
mayexchangeinformationinrelationtoyoutoenableElectroluxtomeet
itsobligationsunderthiswarranty.
Warranty
FORSALESINAUSTRALIAANDNEWZEALAND
APPLIANCE:KELVINATORSPLITSYSTEMAIRCONDITIONER
Important Notice
Beforecallingforservice,pleaseensurethatthestepslistedinpoint13abovehavebeenfollowed.
FOR SERVICE
ortondtheaddressofyournearest
stateservicecentreinAustralia
PLEASE CALL 13 13 49
Forthecostofalocalcall(Australiaonly)
SERVICE AUSTRALIA
ELECTROLUXHOMEPRODUCTS
www.electrolux.com.au
FOR SPARE PARTS
ortondtheaddressofyournearest
statesparepartscentreinAustralia
PLEASE CALL 13 13 50
Forthecostofalocalcall(Australiaonly)
FOR SERVICE
ortondtheaddressofyournearest
authorisedservicecentreinNewZealand
FREE CALL 0800 10 66 10
(NewZealandonly)
SERVICE NEW ZEALAND
ELECTROLUXHOMEPRODUCTS
www.electrolux.co.nz
FOR SPARE PARTS
ortondtheaddressofyournearest
statesparepartscentreinNewZealand
FREE CALL 0800 10 66 20
(NewZealandonly)
KSSAC_Warr_Apr11
Installation and maintenance of
HEPA filter
Check after installation and
operation test
Check after installation
Items to be checked Possible malfunction
Has the unit been
fixed firmly?
The unit may drop, shake
or emit noise.
Have you done the
refrigerant leakage test?
It may cause insufficient
cooling (heating)
Is thermal insulation
sufficient?
It may cause condensation.
Is water drainage
satisfactory?
It may cause water leakage.
Is the voltage in accordance
with the rated voltage
marked on the nameplate?
It may cause electric
malfunction or damage
the unit.
Is the electric wiring or
piping connection installed
correctly and securely?
It may cause electric
malfunction or damage
the parts.
Has the unit been
securely earthed?
It may cause electrical
leakage.
Is the power cord specified?
It may cause electric
malfunction or damage
the parts.
Is the inlet or outlet
blocked?
It may cause insufficient
cooling (heating)
Is the length of connection
pipes and refrigerant
capacity recorded?
The refrigerant capacity is
not accurate.
Operation Test
1 Before Operation Test
a. Do not switch on power before installation is
finished completely.
b. Electric wiring must be connected correctly
and securely.
c. Cut-off valves of the connection pipes should
be opened.
d. All the impurities such as scraps and waste must be
cleared from the unit.
2 Operation Test Method
a. Switch on power and press "ON/OFF" button on the
remote controller to start the operation.
b. Press MODE button to select the COOL, HEAT (Not
available with Cooling Only models), FAN to check
whether the operation is normal or not.
Installation of HEPA Filter
1 Lift up the front panel from the two ends of it, as shown
by the arrow direction, and then remove the air filter
Air filter
HEPA filter
2 Attach the HEPA filter onto the air filter
Air filter
HEPA filter
3 Install the air filter properly along the arrow direction in
the diagram below, and then close the panel
Air filter
HEPA filter
Cleaning and Maintenance
Remove the HEPA filter and reinstall it after cleaning
according to the installation instruction. Don't use brush or
hard things to clean the filter. After cleaning, be sure to dry it
in the shade.
Service Life
The general service life for the HEPA filter is about one year
under normal conditions.

© 2011 Electrolux Home Products Pty Ltd ABN 51 004 762 341
Print code: Airwave_IM_Jul11
If you’d like further information about Kelvinator
appliances, please visit your retailer, phone or email
our Customer Care team or visit our website.
telephone: [phone]
fax: [phone]
email: [e-mail]
web: www.kelvinator.com.au
Kelvinator. We are part of the Electrolux family.
Share more of our thinking at www.electrolux.com.au