Kentec Electronics Taktis TRC00NC-10 Technical manual

Taktis Network Vision Annunciator
Information Guide
UL Version 1.04 |May 2019 |MAN-1434KE

CONTENTS
Contents 2
Compliance 3
Underwriters Laboratories (UL) 3
FCC 3
Installation 3
Introduction 4
Technical Support 4
Return Material Authorization (RMA) 4
Warranty Service 5
Advanced Replacements 5
Overview 6
Fascia 8
Internal Components 9
Installation 10
Before You Begin 10
Mounting the Vision Annunciator 12
Trim Ring 13
Wiring 16
Specifications 19
Cabling 20
Index 21
Glossary 22
Taktis Network Vision Annunciator Information Guide
Kentec Electronics Ltd
Taktis Network Vision Annunciator Information Guide
UL Version 1.04 |May 2019 |MAN-1434KE
Page 2

COMPLIANCE
Underwriters Laboratories (UL)
Fire Alarm Subassembly
Kentec Electronics Ltd
FCC
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of the FCCRules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the Installation Manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense. Any
changes or modifications not expressly approved by Kentec Electronics Ltd could void the user's authority to
operate this equipment under the rules and regulations of the FCC.
Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
Installation
Install this product in accordance with NFPA 13, NFPA 72, NFPA 70, and NEC 70 and all local codes.
All field wiring should be installed using fire rated cables according to the NFPA 72. Riser conductors shall be
installed in accordance with the survivability from attack by fire requirements in National Fire Alarm Code, NFPA
72, Section 12.3. Riser conductors shall employ either a 2 hour rated cable system, or meet requirements
approved by the AHJ.
Kentec Electronics Ltd
Taktis Network Vision Annunciator Information Guide
UL Version 1.04 |May 2019 |MAN-1434KE
Page 3
Taktis Network Vision Annunciator Information Guide

INTRODUCTION
Technical Support
For technical support, contact Kentec Electronics, Ltd at [phone] or [e-mail].
Prior to contacting technical support, have the following information available:
nProduct part number
nPurchase order or order number
nProduct serial number
nCurrent function of the product
nExpected function of the product
nInstallation of the product
Return Material Authorization (RMA)
Contact Technical Support to obtain an RMAfor any product to be returned. Returns will not be accepted
without an accompanying RMA number. An RMA number is assigned when:
lTech Support acknowledges a possible product failure.
lA product was damaged during shipping
lAn incorrect product was shipped
lAn order was placed using an incorrect part number *
lAn order was placed using an incorrect part quantity *
lAn order is no longer required *
* Restocking fees may apply.
All returned products are tested to confirm operating failures experienced in the field. If the product is found to be
functional, contractors must absorb expenses for return shipping, as well as the cost and shipping of the
advanced replacement product.
Prominently display the RMA number on all packages sent for return. Ship all return products to:
Attention: RMA # _____________
Kentec Electronics, Ltd
Units 25-27 Fawkes Avenue
Taktis Network Vision Annunciator Information Guide
Kentec Electronics Ltd
Taktis Network Vision Annunciator Information Guide
UL Version 1.04 |May 2019 |MAN-1434KE
Page 4

Questor, Dartford
Kent. DA1 1JQ
United Kingdom
Warranty Service
Technical Support can replace or repair a defective product when the original purchase is within the warranty
period defined in the sales contract. Check your contract for more information, or contact your sales
representative about your specific warranty period.
Advanced Replacements
Products that fail to operate in the field can be replaced quickly using the advanced replacement process. The
advanced replacement process is available to all contractors who maintain an acceptable line of credit.
Initiate the advanced replacement process by requesting an RMA number from a Tech Support representative.
Advanced replacements can be shipped to your location when the product is covered under warranty and when
a replacement product is in stock.
lAdvanced replacements can be expedited at the request of the contractor. Shipping costs associated with
this process are the responsibility of the contractor.
lProducts returned using the advanced replacement process must be received within 30 days of the RMA
issue date.
Kentec Electronics Ltd
Taktis Network Vision Annunciator Information Guide
UL Version 1.04 |May 2019 |MAN-1434KE
Page 5
Taktis Network Vision Annunciator Information Guide

OVERVIEW
Taktis NetworkVision Annunciator
TRC00NC-10 (Red), TRC00NC-40 (Gray), TRC00NC-60 (Black)
The Taktis Network Vision Annunciator is a display and control unit which duplicates the indications and primary
controls of Taktis Fire Alarm ControlPanels connected to the same network. The Annunciator connects via the
network interface, and any number of repeaters can be connected up to the maximum number of nodes allowed
by the network.
Taktis Network Vision Annunciator Information Guide
Kentec Electronics Ltd
Taktis Network Vision Annunciator Information Guide
UL Version 1.04 |May 2019 |MAN-1434KE
Page 6

Taktis Network Vision Annunciators can be configured to replicate fire control panel functionality or to operate as
simple, display-only devices for applications where access to fire alarm controls are inappropriate. The
Annunciator can be configured to display events from any combination of nodes on the network.
Kentec Electronics Ltd
Taktis Network Vision Annunciator Information Guide
UL Version 1.04 |May 2019 |MAN-1434KE
Page 7
Taktis Network Vision Annunciator Information Guide

Fascia
Taktis Network Vision Annunciator Information Guide
Kentec Electronics Ltd
Taktis Network Vision Annunciator Information Guide
UL Version 1.04 |May 2019 |MAN-1434KE
Page 8

Internal Components
Kentec Electronics Ltd
Taktis Network Vision Annunciator Information Guide
UL Version 1.04 |May 2019 |MAN-1434KE
Page 9
Taktis Network Vision Annunciator Information Guide

INSTALLATION
This section explains the installation procedure for the Taktis Network Vision Annunciator. Install this product in
accordance with NFPA 72, the National Electrical Code, and all local codes.
qNotify the monitoring center and location security that the Taktis Fire Alarm ControlPanel will be temporarily out of
service.
qRemove the Annunciator from its packaging and check its contents.
qRemove the fascia.
qMount the enclosure to wall.
qReinstall the fascia.
q
Remove AC and battery power from the panel.
WARNING! Failure to remove power during wiring and installation can damage the unit and void the
warranty.
qConnect field wiring. Refer to Wiring below for specific details.
qRestore AC and battery power.
qWait for the panel start-up process to complete. Refer to the Taktis Fire Alarm ControlPanel
InstallationManual (MAN-1431KE) for more information.
qFrom the Annunciator GUI, set the node number. This requires User AccessLevel 3.
qConfigure the Annunciator and all nodes on the network.
qTest the Annunciator to verify proper operation based on the configuration.
WARNING! The Annunciator must be installed by personnel familiar with electronic components. Electronic
components within the module are vulnerable to damage from electrostatic discharge. Ground straps must be worn by
installers before handling to prevent electrostatic discharge damage.
Before You Begin
Before you begin the installation, take a few minutes to review the installation information, gather the required
items, and complete the tasks listed to make the installation as quick and easy as possible. Acquire the following
Taktis Network Vision Annunciator Information Guide
Kentec Electronics Ltd
Taktis Network Vision Annunciator Information Guide
UL Version 1.04 |May 2019 |MAN-1434KE
Page 10