Kenwood KA-87 User manual

STEREO INTEGRATED AMPLIFIER
KA-87/KA-57
INSTRUCTION MANUAL
Introduction
Your choice of this product indicates that you are a
devotee to excellence in sound reproduction.
We appreciate your patronage and take pride in the
long tradition of quality components, that our company
represents.
So that you can get the most out of your unit, we
suggest that you take the time to read through this
manual before you hook up and operate your system.
This will acquaint you with operating features, and
system-connection considerations, so that your listen-
ing pleasure will be enhanced right from the start. You
will notice that in all aspects of planning, engineering,
styling, operating convenience and adaptability, we
have sought to anticipate your needs and desires.
Keep this manual handy for future reference.
For your records
Record the serial number, found on the back of the
unit, in the spaces designated on the warranty card,
and in the space provided below. Refer to the model
and serial numbers whenever you call upon your dealer
for information or service on this product.
Model Serial Number
Unpacking
Unpack the unit carefully and make sure that all ac-
cessories are put aside so they will not be lost.
Examine the unit for any possibility of shipping
damage. If your unit is damaged or fails to operate,
notify your dealer immediately. If your unit was shipped
to you directly, notify the shipping company without
delay. Only the consignee (the person or company
receiving the unit) can file a claim against the carrier for
shipping damage.
We recommend that you retain the original carton and
packing materials for use should you transport or ship
the unit in the future.
KENWOOD
©PRINTED
IN JAPAN B50-8872-00(P, E, M, X, TXT)
89/12 11098 8
7654321 88121109876
ee
Contents
A Before applying POWET ...............:.ceeeceeee eee ee teens 2
A Safety precautions ................ cece cee ce ee ee eee ee cee ee ees 2
A Important safeguards 20.0.0... 000. ccce cee ece ce ccee ee eeee ees 3
System: CONNECTIONS sc ceceess es seee seed eee eee 4-5
Caution : Read the following pages marked A carefully to keep your safety.
Controls, indicators and CONNECtOIS ...... 0... cece 6
Operating instructions. .........0...0c.ccecccceceec eu eneean ees 7
IM GASCOF CIPIC UNL need. ccnsst.b sb dedsaisoyXaetudeedeodected 7
Specifications

A\Caution : Read this page carefully to keep your safety.
Before applying power
Important!
Canada, U.K., Australia and Europe
Units shipped to the Canada is designed for operation
on 120 volts AC only. Units shipped to European coun-
tries are designed for operation on 220 volts AC only.
Units shipped to the U.K. and Australia are designed for
operation on 240 volts AC only. These units are not
equipped with an AC voltage selector switch and the
discussion of such a switch that follows should be
disregarded.
All other countries
Units shipped to countries other than the Canada,
U.K., Australia and European are equipped with
an AC voltage selector switch on the rear panel.
Refer to the following paragraph for the proper
setting of this switch.
AC voltage selection
This unit operates on 110-120 or 220-240 volts AC. The AC
voltage selector switch on the rear panel is set to the voltage that
prevails in the area to which the unit is shipped. Before connec-
ting the power cord to your AC outlet, make sure that the setting
position of this switch matches your line voltage. If not, it must
be set to your voltage in accordance with the following direc-
tion.
Note:
Our warranty does not cover damage caused by excessive line
voltage due to improper setting of the AC voltage selector switch.
AC110-120V~ 4» AC220-240V~ = AC110-120V~< » AC220-240V~
Switch lever
This shows switch
lever locked in the lever locked in the
110-120 V~ posi- 220-240 V~ posi-
tion. tion.
This shows switch
Move switch lever to match your line
voltage with a small screwdriver or other
pointed tool.
AC voltage selector switch
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
For United Kingdom
The mains plug must be removed from the wall socket
prior to any internal examination.
Important
The wires in this mains lead are coloured in accordance
with the following code:
BUG ars atideis cence ae b eres Neutral
BrOWMiii 5 etsetischasabensbeaenredtemeanele’s Live
The wires in this mains lead must be connected to the
terminals in the plug as follows:
Wire colour Plug terminal marking
BUG sees eRs add Gch nade ethane eae N or Black
BPOWN iss tiv sueiees ikwin de tacecdeiu sees L or Red
OE
Brown to
Live
Blue to L
Neutral
N
Plug
Notes:
1) If a 13-amp plug is used, this must be fitted with a 5-amp
fuse.
2) If a 3-pin plug with earthing contact is used, no wire must
be connected to the E terminal.
Safety precautions
Safety precaution for AC plug (for
Canada)
CAUTION: To PREVENT ELECTRIC SHOCK DO NOT
USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD,
RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN
BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
WARNING:
TO PREVENT FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS AP-
PLIANCE TO RAIN OR MOISTURE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SER-
VICING TO QUALIFIED SERVICE PERSONNEL.
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL
TRIANGLE, IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED
“DANGEROUS VOLTAGE” WITHIN THE PRODUCT'S ENCLOSURE THAT MAY BE OF
SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO
ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND
MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING
THE APPLIANCE.
2 KA-87/KA-57 IP)

Important safeguards
Please read all of the safety and operating instructions before
operating this unit. For best results, follow all warnings placed
on the unit and adhere to the operating and use instructions.
These safety and operating instructions should be retained for
future reference. -
1. Power sources — The unit should be connected to a
power supply only of the type described in the operating
instructions or as marked on the appliance.
2. Power-cord protection — Power-supply cords should
be routed so that they are not likely to be walked on or
pinched by items placed upon or against them, pay par-
ticular attention to cords at plugs, convenience recep-
tacles, and the point where they exit from the unit.
Never pull or stretch
the cord.
3. Ventilation — The unit should be situated so that its
location or position does not interfere with its proper ven-
tilation.
To maintain good ventilation, do not put records or a
table-cloth on the unit. Place the unit at least 10 cm
away from the walls.
4. Water and moisture — The unit should not be used
near water — for example, near a bathtub, washbowl,
kitchen sink, laundry tub, in a wet basement, or near a
swimming pool, etc.
5. Temperature — The unit may not function properly if
used at extremely low, or freezing temperatures. The
ideal ambient temperature is above +5°C (41°F).
6. Heat — The unit should be situated away from heat
sources such as radiators, heat registers, stoves, or other
units (including amplifiers) that produce heat.
A Caution : Read this page carefully to keep your safety.
7. Electric shock — If a metal object, such as a hair pin or
a needie, comes into contact with the inside of this unit,
a dangerous electric shock may result. For families with
children, never permit children to put anything, especial-
ly metal, inside this unit.
8. Enclosure removal — Never remove the enclosure. /f
the internal parts are touched accidentally, a serious
electric shock might occur.
. AC outlets — Do not connect other audio equipment
with a power consumption larger than that specified to
the AC outlet on the rear panel. Never connect other
electrical units, such as an iron or toaster, to it to prevent
fire or electric shock.
~“
~~
_
The maximum capacities indicated for the AC outlets on
the rear panel of the this unit are as follows.
1. SWITCHED outlets =; 100 W (Total)
2. UNSWITCHED outlet ; 100 W
. Cleaning — Do not use volatile solvents such as
alcohol, paint thinner, gasoline, or benzine, etc. to clean
the cabinet. Use a clean dry cloth.
2)
ees Wea
2
11. Abnormal smell — |f an abnormal smell or
smoke is detected, immediately turn the power
OFF and pull out the power cord. Contact your
dealer or nearest service station.
“y)_ POWER OFF!
an WO Re,
o) === OC ]?
Oo —pd
—___—-—
KA-87/KA-57 (P} 3

System connections
Turntable Tuner Tape deck 1
Line in Line out
Except Australia, Europe and U.K.
KA-87/KA-57
KA-87 only
SPEAKER
'WAPEDANCE SELECTOR’
LESS THAN B04 60 OR MORE
ci UNSWIT CHE
x
SWITCHED.
TOTAL 10GW MAX 100W MA,
U)
To AC outlet
Line in Line out
pa eye |
i
Tape
deck
2
9
Right
Left
Speaker
system
A
Speaker
system
B
Speakers
This
amplifier
has
two
pairs
of
speaker
terminals,
SPEAKERS
A
and
SPEAKERS
B.
10mm
—
@)
®
Connecting
one
speaker
system
Peal
Remove
insulation
Twist
wire
tightly,
Connect’
speakers
rated
at
8
ohms
or
more
(USA
and
=
trom
lead
tip.
soosm{
and
solder.
Canada),
4
ohms
or
more
(Others)
to
the
SPEAKERS
A
terminals.
Connecting
two
speaker
systems
®
{fr
be
®
Y
®
To
connect
an
additional
pair
of
speakers,
use
the
B
ter-
cf
>
minals. In this case, each speaker must be rated at ix] =
8 ohms or more (USA and Canada), 4 ohms or more je
(Others) : Raise the lever. Insert the wire The wire is now
Connection
with
speaker
cords
and
return
the
locked.
1.
Connect
the
left
speaker
to
the
SPEAKERS
ter-
eve.
minals and the right speaker to the [R] SPEAKERS Speaker lead connection
terminals.
2. Be careful that wires do not contact adjacent ter-
minals.
3. Be sure to connect the (+) terminal of the speaker to
the (+) terminal of the amplifier.
Never short the (+) and (—) terminals.
Erroneous connection of speakers may result in poor
imaging or unnatural sound.
4 kA-87/KA-57 (P)

Setting SPEAKER IMPEDANCE SELECTOR
(KA-87 only)
According to the impedance of the speakers used, set
the SPEAKER IMPEDANCE SELECTOR at rear as
follows.
49,60 — ‘‘LESS THAN 8 Q”
80, 162 — "8 Q OR MORE’
SPEAKER
IMPEDANCE SELECTOR
LESS THAN 82 «™ 80 OR MORE
( (1)
Notes: ———___$_$__
1. During speaker system connection and operation of SPEAKER IM-
PEDANCE SELECTOR, set the POWER switch to OFF.
2. Check that the connected lead wires of the speaker systems do
not contact with other jacks or terminals.
Turntable
The PHONO jacks of the amplifier can accept a turntable
with an MM type phono-cartridge.
Your stereo turntable has RCA pin-plug cords that is
terminated with phono plugs. Plug the left channel plug
into the and the right channel plug into the [R]
PHONO jacks.
If the turntable has a ground wire, connect it to the
unit’s GND terminal to avoid hum.
Tuner
Use the TUNER jacks for connection to an FM stereo or
AM-FM stereo tuner.
Connect the left channel of the tuner to the [L] TUNER
input jack and the right channel of the tuner to the [R]
TUNER input jack.
CD/AUX
To these jacks, high-level signal sources such as, CD
player, tuner, extra tape decks, TV, VTR sound out-
puts, etc. can be connected.
Ground
For maximum safety and minimum interference con-
nect the GND terminal to a good earth ground if prac-
ticable. A good earth ground is a metal stake driven into
moist earth. However, never use a gas pipe for this pur-
pose.
Tape deck
If only one tape deck is to be connected to the system it
iS recommended that it be connected to the jacks mark-
ed TAPE 1.
Tape deck input and output cables are normally ter-
minated with phono plugs.
Playback
Plug the left and right output cables of the tape deck into
the [0] and [R] TAPE 1 PLAY jacks.
Record
Plug the left and right input cables of the tape deck into
the (L] and [R] TAPE 1 REC jacks.
Second tape deck
Plug the input and output cables from the second tape
deck into the REC and PLAY jacks marked TAPE 2.
AC outlets (Except Australia, Europe and U.K.)
The AC outlets on the rear panel of the power sup-
ply unit may be used to supply power to other com-
ponents in the system, such as turntables, tape decks,
etc. Never connect equipment whose power consump-
tion exceeds the maximum value shown at each outlet.
1. SWITCHED outlets: These outlets supply power
only when the unit is turned on. The maximum total
capacity (both outlets) is 100 watts.
2. UNSWITCHED outlet: The outiet provides power
when the unit is plugged into an active AC wall
outlet, regardless of the setting of the POWER
switch. The maximum capacity is 100 watts.
KA-87/KA-57 (P) 5

Controls, indicators and connectors
KENWOOD stereo INTEGRATED AMPLIFIER i ee el maar ae ONTROL
INPUT INDICATOR ———
2 Ee
INPUT SELECTOR:
POWER switch/POWER indicator
Press the POWER switch to turn on power. The POWER
indicator lights up.
PHONES jack
Stereo headphones are plugged into this jack.
SPEAKERS switch
A, B OFF — This position silences all speakers to permit
private use of headphones.
A ON — Activates speakers connected to the
SPEAKERS A terminals on the rear panel.
B ON — Activates speakers connected to the
SPEAKERS B terminals on the rear panel.
A, B ON — Activates speakers connected to the
SPEAKERS A and B terminals simultaneously.
TONE CONTROL knobs
BASS — Turn from the FLAT position to the right to in-
crease bass response.
Turn to the left to lower bass response.
TREBLE — Turn from the FLAT position to the right to in-
crease treble response.
Turn to the left to reduce treble response.
BALANCE control knob
This control is to balance left and right channels when an
imbalance exists from the sound source, or to correct
acoustic imbalance due to room conditions.
Turn the control from the CENTER position to the left to
reduce the right channel.
Turn to the right to reduce the left channel.
LOUDNESS switch
This switch is for listening at very low volume level. Press
this switch to boost the low level.
6 kA-87/KA.57 (P)
Y (KA-87 only)
@ TAPE 2 selector switch
To listen to a source of the tape deck, etc., connected to
the TAPE 2 jacks, press this switch.
Note: ——___
The TAPE 2 selector switch has a priority over the input selector
switches. To listen to the source other than tape deck 2, be sure
to set this switch to OFF.
INPUT SELECTOR
PHONO — Selects the program source played on the
turntable.
TUNER — Selects the tuner connected to the TUNER
jacks.
CD/AUX — Selects the source connected to the
CD/AUX jacks.
TAPE 1 — Press this switch to play back a tape deck
connected to TAPE 1 jacks.
Note:
When TAPE 1 and TAPE 2 switches are pressed, TAPE 2 setting
has priority.
MUTING switch (KA-87 only)
When this switch is pressed, the overall sound level can
be decreased by — 20 dB so the volume can be reduced.
The MUTING switch is convenient for listening in low
level, because the volume control becomes more
delicate when the switch is ON.
VOLUME CONTROL knob
This control adjusts left- and right-channel volume
simultaneously. Set it for the required listening level.
INPUT INDICATORs
The indicator lights corresponding to the INPUT SELEC-
TOR switch pressed.
TAPE MONITOR indicator
TAPE 2 — Lights when the TAPE 2 switch is pressed.

Operating instructions
Volume, tone, balance and loudness
1. Turn up VOLUME CONTROL to the required listening level.
2. Adjust TONE CONTROLS to suit your taste.
3. If an imbalance occurs (the left or right channel appears
louder than the other) due to source imbalance or room
acoustics, adjust BALANCE control to equalize the sound
from both speakers.
4. If you customarily listen at low listening levels, set the
LOUDNESS switch to ON. If not, set it to OFF position.
Tuner
1. Press the INPUT SELECTOR TUNER switch.
2. Operate the tuner as usual.
3. Adjust VOLUME CONTROL and TONE CONTROLS for your
preference.
Turntable
1. Press the INPUT SELECTOR PHONO switch.
2. Set the turntable in operation.
3. Adjust VOLUME CONTROL and TONE CONTROLS for your
preference.
CD/AUX jack
1. Press the INPUT SELECTOR CD/AUX switch to select out-
put from the sources connected to CD/AUX jacks.
2. Operate unit connected to CD/AUX jacks according to the
operating instructions of each unit.
3. Adjust VOLUME and TONE CONTROLS to your preference.
In case of difficulty
Tape decks
© Recording
1. Press the appropriate INPUT SELECTOR switch (PHONO,
TUNER or CD/AUX).
2. Set up your tape deck for recording and set the recording
level with the controls on your tape deck. The VOLUME
and TONE CONTROLs on the amplifier do not affect the
signal applied to the tape deck for recording.
3. Adjust listening level and tone at the amplifier to suit your
listening preference.
© Tape monitoring
If tape deck is equipped with monitoring mechanism, you can
monitor the sound quality of the recording in progress.
1. Press the TAPE 2 switch.
2. When recording starts, you can hear the recording sound.
¢ Tape playback
Press the TAPE switch or the INPUT SELECTOR CD/AUX
switch to play back a cassette which has been recorded by
the tape deck connected to the TAPE or CD/AUX jacks.
Adjust listening level and tone at the amplifier to suit your
listening preference.
When the sound cannot be heard even if the operation
is correct, turn off the power switch and check if the
speaker terminals are not short-circuited.
lf
your
unit
should
not
perform
as
expected,
consult
the
table
below
to
see
if
the
problem
can
be
corrected
before
seeking
help
from your dealer or service representative.
AM, FM, PHONO or TAPE
playback
clockwise.
Power on but no sound. 1. Power cord not plugged in.
2. Poor connection at wall outlet.
Power outlet inactive.
4. Speaker cords disconnected.
5. Speakers switched off.
6. No INPUT SELECTOR switch is in | 6. Push one of the INPUT SELECTOR
1. Check plug contact.
2. Check outlet using a lamp or other
appliance (outlet may be controlled
by a wall switch).
3. VOLUME CONTROL set fully counter- | 3. Set the control to your preference.
4. Check speaker connections.
5. Check speaker switch.
2. Defective speaker.
use. switches to select the required pro-
gram.
Sour
from
left
or
right,
but
not
both.
1.
Poor
speaker
connections.
1.
Check
connections
at
both
ends
of
speaker cord.
2. Reverse speakers. !f problem stays
with the same speaker, have speaker
3. BALANCE control set to one
extreme or the other.
checked.
3. Check setting of BALANCE control.
Record playback only
Cause
Remedy
Loud hum drowns out sound.
Poor ground connection at phono cable
connections.
Check phono plugs, particularly outer-
Low background hum.
Hum Picked up in turntable or turntable
cables.
he connections.
Keep cables away from power cords.
Twist left and right cables toge ther.
Reverse AC plug of turntable. Connect
ground wire between turntable and
GND connector.
Background buzz.
TV signal picked up by phono cable
(especially near transmitter).
Route phono cables to minimize buzz.
Howling noise at maximum volume set-
tings.
Acoustic pickup from speaker.
Increase distance between speaker and
turntable. Choose speaker locations
carefully. Check turntable suspensi ON.
i
KA-7/KA-57 IP) 7

Specifications
KA-87
KA-57
Audio Section
Rated Power Output
50 watts per channel minimum RMS, both channels
driven, at 8 ohms from 20 Hz to 20,000 Hz with no
more than 0.09% total harmonic distortion.
Maximum Continuous power output (IEC/NF) from
63 Hz to 12,500 Hz, 0.7% T.H.D.
8 ohms.................0.0.0008. 55 W+55 W
Both Channels Driven........... 60W+60W B8o0hms at
1,000 Hz
75W+75W 4ohms at
1,000 Hz
Music Power Output at
8 ohms .......000.0.0. eee 100 W+ 100 W
Total Harmonic Distortion
LINE input to SPEAKER output
(20 Hz to 20,000 Hz)....... 0.09% at rated power into
Audio Section
Rated Power Output
100 watts per channel minimum RMS, both chan-
nels driven, at 8 ohms from 20 Hz to 20,000 Hz
with no more than 0.05% total harmonic distortion.
Maximum Continuous power output (IEC/NF) from
63 Hz to 12,500 Hz, 0.7% T.H.D.
8 ohMs.....................0008- 80 W+80 W
- Both Channels Driven........... 6B5W+65W 4ohms at
1,000 Hz
110 W+110 W 8ohms at
1,000 Hz
‘Music Power Output at
8 ohms .....................500088 225 W+225 W
Total Harmonic Distortion
LINE input to SPEAKER output
(20 Hz to 20,000 Hz)....... 0.05% at rated power into
(20 Hz to 20,000 Hz)......
(V2) bs. Sioned jecebotenc cones
intermodulation Distortion.....
(60 Hz:7 kHz = 4:1)
Damping Factor ..................
Power Bandwidth................
Frequency Response ............
Input Sensitivity/Impedance
PHONG | 6.hcoessi snes cneck ones
Tuner, Tape play, CD/AUX..
Signal-to-Noise Ratio (IHF-A)
Phono ...................0.0:0000e
Tuner, Tape play, CD/AUX..
8 ohms
0.03% at 1/2 rated power into
8 ohms
0.004% at 1/2 rated power in-
to 8 ohms
0.03% at rated power into
8 ohms
40 (50 Hz at 8 ohms)
10 Hz to 100 kHz at 0.2%
T.H.D. 8 ohms
10 Hz to 7OkHz, +0aB,
~—3 dB
2.5 mV/47 k ohms
150 mV/27 k ohms
(IHF’66)
75 dB for 2.5 mV input
81 dB for 5.0 mV input
100 dB
Signal to Noise Ratio Unweighted at 50 mW (DIN)
PHONO 05.05 008s cee cerecrccnsan
Tuner, Tape play, CD/AUX..
Channel Separation at 1 kHz
Phono (Terminated with
2.2 kohms)....................
57 dB
59 dB
(DIN)
Tuner, Tape play, CD/AUX (Terminated with
47 kohms +250 pF) .......
Phono Input Capacity (DIN) ...
Phono Maximum input Level ..
Output Level/Impedance
Tape REC (Pin)..................
Phono Frequency Response...
Tone Control
Bas8). i.) secu koeectouse. Re otds
THODIG ss ils Steidn 2 aceer eet:
General
Power Consumption ............
Dimensions........................
Weight (Net) ......................
Note:
44 dB
220 pF
170 mV, T.H.D. 0.05% at
1 kHz
150 mV/330 ohms
RIAA standard curve +0.5 dB
(20 Hz to 20 kHz)
+9 dB at 100 Hz
+8 dB at 10 kHz
+8 dB at 100 Hz
(at —30 dB VOLUME Level)
3 A(U.S.A. & Canada models)
200 W (Other countries)
W: 420 mm (16-9/16”)
H: 110mm (4-5/16”)
D: 277 mm (10-7/8”)
6.1 kg (13.4 Ib)
(20 Hz to 20,000 Hz) ......
(TMZ) cose cctisssec seis teas
intermodulation Distortion.....
(60 Hz:7 kHz= 4:1)
Damping Factor ..................
Power Bandwidth................
Frequency Response............
Input Sensitivity/Impedance
Phono ..................:0::0ceee es
Tuner, Tape play, CD/AUX..
Signal-to-Noise Ratio (IHF-A)
Phono ......... 0.0.00. cece cceeeees
Tuner, Tape play, CD/AUX..
8 ohms
0.04% at 1/2 rated power into
8 ohms
0.004% at 1/2 rated power in-
to 8 ohms
0.03% at rated power into
8 ohms
30 (50 Hz at 8 ohms)
10 Hz to 100 kHz at 0.2%
T.H.D. 8 ohms
10 Hz to 7OkHz, +0OaB,
—3 dB
2.5 mV/47 k ohms
150 mV/33 k ohms
(IHF’66)
75 dB for 2.5 mV input
81 dB for 5.0 mV input
100 dB
Signal to Noise Ratio Unweighted at 50 mW (DIN)
PHONO :..23..5 so ccece sae cccthesias
Tuner, Tape play, CD/AUX..
Channel Separation at 1 kHz
Phono (Terminated with
2.2 kohms)....................
57 dB
59 dB
(DIN)
Tuner, Tape piay, CD/AUX (Terminated with
47 kohms + 250 pF) .......
Phono Input Capacity (DIN) ...
Phono Maximum Input Level..
Output Level/impedance
Tape REC (Pin)..................
Phono Frequency Response...
Tone Control
Bass). 2.cse idles
Treble: sii0.ctiicte econ vases!
Loudness Control ................
General
Power Consumption ............
Dimensions ........................
Weight (Net) .................0..
55 dB
220 pF
170 mV, T.H.D. 0.05% at
1 kHz
150 mV/330 ohms
RIAA standard curve +0.5 dB
(20 Hz to 20,000 Hz)
+9 dB at 100 Hz
+8 dB at 10 kHz
+8 dB at 100 Hz
(at —30 dB VOLUME Level)
4 A(U.S.A. & Canada models)
160 W (Europe, U.K. and
Australia model)
220 W (Other countries)
W: 420 mm (16-9/16”)
H: 110mm (4-5/16”)
D: 277 mm (10-7/8”")
6.7 kg (14.7 Ib) (Europe, U.K.
and Australia model)
7.2kg (15.81b) (Other
models)
KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without
notice.