9
KDC-1032/132/132CR
KDC-133/233/234SGY
TEST MODE
●How to enter the test mode
• Press Preset [1] and Preset [3] keys simultaneously to re-
set the unit.
●How to clear the test mode
Reset. (Do not clear by Power OFF and ACC OFF.)
●Initial conditions of the test mode
• Source is STANDBY.
• Displays lights are all turned on.
• The volume is at -10dB (The display is 30).
• CRSC is OFF, regardless of whether there are switching
functions or not.
• LOUD is OFF.
• SYSTEM Q is NATURAL (FLAT).
• BEEP should always work by pressing a key.
●Test mode specification forTUNER
• TUNER (FM) Preset [4] key shall be 98.3MHz.
●CD receiver test mode specifications
•Forceddischargingoperation isprohibited at reset start.Note
that a CD is not to be recognized by reset when it is in-
serted.
•[Track up] key triggers a jump to the following tracks.
No. 9 →No. 15 →No. 10 →No. 11 →No. 12 →No. 13 →
No. 22 →No. 14 →No. 9 (recursive)
• [Track down] key moves back to the previous track from the
current track.
• Preset [1] key triggers a jump to No. 28.
• Preset [2] key triggers a jump to No. 14. (Scan function is
invalid.)
●Audio adjust mode
• Pushing the [VOL] key enters the audio function mode.
• The initial item is Fader. (FAD →BALANCE →BASS →
MID →TRE)
• Use [AM/FM] key to switching items.
• Use [Seek Up/Down] key to switching the adjusted value.
• Adjust Fader/Balance to three levels (15 ↔0 ↔15) with
Volume up/down. (initial value: 0)
•Adjust Bass/Middle/Treble to three levels (-8 ↔0 ↔+8)
with Volume up/down.(initial value: 0)
• Pressing the [VOL] key for more than a second enters the
audio setup mode.
• Use [AM/FM] key to switching items.
• Use [Seek Up/Down] key to switching the adjusted value.
• Adjust Volume offset to two levels (-8 ↔0). (initial value: 0)
• Initialize everything with the [Track-Up] key in the standby
source.
• Pressing [∗] key on the remote controller enters the audio
adjustment mode.(Use [∗] key to cancel.KDC-132CR only)
• Continuous feed with a remote controller shall not be used.
Pressing a key activates a motion.(KDC-132CR only)
●Special display when all lights are on
The following information will be displayed by pressing the
preset key when STANDBY indicators are on.
[1] key •
Press [1] key.The current destination SW is displayed.
(Display) TP-X
•Press a key while the destination SW is displayed.
Version display (month, date, hour, minute in 8 digits)
(Display) XXXX xxxx
[2] key • All LCD light up.
[3] key • Press the key for less than a second:Power-on time
display (STANDBY time should not be counted).
• Press the key for more than 2 seconds while the
power-on time is displayed:The power-on time is
cleared.
(Display) Pon_x XXXX MAX 60000 (time)
[4] key • Press the key for less than a second:CD operation
time display.
•Press the key for more than 2 seconds while the CD
operation time is displayed:CD operation time is
cleared.
(Display) PLY_x XXXX MAX 60000 (time)
[5] key • Press the key for less than a second:CD EJECT
count display.
•Press the key for more than 2 seconds while the CD
EJECT count is displayed: CD EJECT count is
cleared.
(Display) EJC_x XXXX MAX 60000 (time)
