Kenwood KID60B10 User manual

Chapter InsⅠtallation-------------------------------------------------------------1
1.1 Safety Instructio n------------------------------------------------------- 1
1.2 Installation Instruction--------------------------------------------------- 2
Chapter Maintenance--- -------------------------------------------------------- 3
2.1 Foreword--------------------------------------------------------------3
2.2 Troubleshooting-------------------------------------------------------- 3
2.3 Note---------- --------------------------------------------------------6
2.4 Attached drawing s-------------------------------------------------------6
Electric diagram-------------------------------------------------------- 7
Ⅱ
After unpacking, the appliance should be checked to see if there is any damage to it.
The dishwasher is intended to wash dishes and plates by adults.
When using the dishwasher , some basic principals should be followed:
1) Extended power cord and adaptor shoul d not be used.
2) The power cord should not be too long or knotted.
3) Switch off the power before making any repair of the dishw asher.
Children should be kept away from the detergent and the opened dishwasher.
Then dishwasher should not be installed in an unsheltered place or exposed to the rain or other
natural environment.
Never touch the heating element during or immediately after use.
The dishwasher should not be lean on or sit on when it is open , otherwise it will be overturned.
If the dishwasher malfunctions, turn off the water inlet and cut off the power before you read the
instruction of Chapter . If the problems cannot be solved by yourself, please contact the
professional technicians.
The dishwasher could not be repaired by unprofessional personnel with non-original spare parts.
It is recommended that if the dishwasher will not be used for a long time, it should be cut off the
water inlet, remove the plug and keep the door of dishwasher a jar.
1.1 Safety Instruction
Ⅱ
1

2
1.2 Installation Instruction
Unpacking
1) Removing the packing accessories, please pay attention that the plas tic bag should be out of the
reach of children.
2) Open the door of the dishwasher to check the baskets are placed in the proper place
(man u fact ures may fix th e baskets by so me simp le ways for the sake of safety).
Locate the dishwasher
1) The dishwasher should be kept away from heating resources and not be exposed to the sun to
prevent its coating from fading or falling off.
2) The back of the dishwasher shoul d rest against the wall behind it and the sides, along the
adjacent cabinets or wall. The water supply and drain hose of the dishwa sher could be positioned to
the right of the left to facilitate proper installation.
3) The dis hwasher should be built in the cabinet and fixed it on the cabi net by two screw.
Installat ion steps
1)
2)
3)
4)
5)
6)
Install the aesthetic pannel on the outer door of the dishwasher.
Adjust the tension of door spring.
level the dishwahser and touch the cabinet by adjusting the four leveli ng legs individually.
Conne ct the inl et, and drain hoses, and power cord .
pushing the dishwasher into the cabinet.
fixing the dishwasher into the cabinet by two countersunk head screw.
5
3
Installation steps
1
Aesthetic
pan el
2
6
When you want more particular content about installation, please to see the installation
manual we edited.

3
2.1 Foreword
Before any repair service, you should check:
a) Whether the dishwasher is properly installed according to the in stallation manual.
b) Whether the damaged components have been repaired or not.
c) Whether the charging hose and the drain hose are properly installed.
d) Whether the dishwasher is level or not.
e) Whether there is salt in the water softener.
f) Whether there is rinse agent in the dispenser.
The circuit board is the centrum of the whole control system of the dishwasher. When dishwasher is
w ashing though a information comes to the circui t, then th e circuit deli vers var ious dictate to
every department of dishwasher to keep the dishwasher mo ving. the dishwasher move with a
arranged program. If you know the program and structure o f the dishwasher, the bel ow table shoule
be helpful to establish a resolve to any problems occurred.
2.2 Troubleshooting
Questions put forward by users
By misusage of users
T he pro bl ems o f th e d i shwa sh er itself
T he di sh wash er do es no t st art
* Something wrong with the socket
* No water (the water valve is closed)
* Improper electrical connection
* The door is not properly closed
* Incorrect position of charging hose
* Power cord
* "ON/OFF" switch
* Door switch
* Water inlet valve
* Pressure switch
* Aqua-stop switch
Water floods in the dishwasher
* Air leakage of the chamber
* The hose of pressure switch
* Pressure switch
* Water inlet valve
The dishwasher does not heat
* Malf un ction of h eating element
* The circuit is not properly contacted
* Malf un ction of t he thermocouple
No water comes into the dishwasher
* Wat er supply is cut off
* The filter of the water inlet valve is
clogged.
* Connection to the inlet valve is
broken or damaged.
* Electrical connection is cut off.
* Pressure switch
* Aqua-stop switch
* The softener is blocked.
The problems of the dishwasher itself
* Air leakage of the chamber
* The hose of pressure switch
* Pressure switch
* Water inlet valve

4
The dishes are not clean enough after
washing
* The f ilter is clogged.
* Unqualified d etergent or the dosage
in the container is not correct.
* No salt in the softener
* No rinse agent
* Incorrect load ing of dishes *
Someth ing wro ng with the drain pipe
in the home
* Flow and pressure of washing pump
* Detergent is not released from
dispenser
* Heating element is not working
* The n ozzle is blocked by food
particles
* No water c oming into the
dishwasher
* The d ispe nser malfunctions
* Sth wrong with the pressure switch
and the cha rging water is not enough
The dishwasher doesn't
wash properly
* Wrong loading position of the dishes.
* Short circuit of startup capacitance
* Washing motor is blocked or burnt
* Pressure switch
* Malfunction of t he circuit board
T he di sh es ar e wet
* The customer chose the program
without drying performance
*Therm ocouple doesn't work
properly
* Heating element has malfunctioned
* Somet hing is wrong with t he
circuit board
The dishes are no t completely dried * Incorrect loading of the dishes
* Earlier opening of the door
* No rinse agent or th e dosag e is not
enough
* Incorrect program selection
* The passage of the air breather is
blocked
* The d rain pu mp does not drain out
water
* Detergent is not released from the
dispenser
* Nois e fro m washin g pump
* Noise from drain pump
* Noise from water inlet valve
*Noise from air breather
Too much noise * Incorrect loading of dishes
Electrical charges from
dishwasher
* The electrical wire in the house is
not earthed.
* Connection of the t erm inal box
* Ground ing of the heat ing elemen t
* Circuit and its components
Water leakage an d flood of the
dishwasher
* Too much detergen t
* Using the detergent not int ended
for use with dishwashers.
* Flow and pressure of washing pump
* Detergent is not released from
dispenser
* Heating element is not working
* The n ozzle is blocked by food
particles
* No water c oming into the
dishwasher
* The d ispe nser malfunctions
* wrong with the pressure
switch
someth in g
re ducing water pressure
* Pressure switch
* Door gasket
* Water leakage of pipes, gaskets
and bolts
* Drain hose
* Washing pum p
* Softener valve
* Softener
* Air breather

5
Unusuel smell in the dishwasher
* Food particles on the tub bot tom
* Food particles on the heating
element
* Plastic dish es used in t he
dishwasher
* Th e w ater t emperatu re is too
high when drying (overheating)
* Th erm ocou ple do esn 't
work prope rly
Long time for a washing cycle
* Inlet pressure is too low
* Incorrect location of charging
and drain hoses or they are bent
* The filter of inlet valve is blocked
* The drain hose is crimped or bent
* Malfunction of t he drain pum p
* Infill of t he inlet valve is blocked
* Clog of the softener
* Malfunction of t he therm ocouple
The det ergent co uld not be released
from the dispenser
* Bad quality of the det ergent
* The detergent is damped int o
blocks
* Wrong location of the dishes
* Th e plug of detergent container
could not be opened.
* No act ion of the solenoid valve of
electric feeding dispenser.
* Malf un cti on of the elect ric circuit
* Malf un cti on of the th ermocoup le
Dishwasher stops when cyclin g
* The door is not completely shut
* The f ilter is blocked
* Too much detergent
* Electric ci rcuit
* Door swit ch
* Pressure switch
* Th e circui t b oard
* Power switch
Dishes are damaged or glassware is
broken
* The dishes are n ot suitable for
washing in the dishwasher
* The dishes are overturned
* Th e w ash i ng temp eratu re is n ot
suitable for glassware
* Basket is damaged
* Malf un cti on of the th ermocoup le
T he di sh wash er do es no t drai n * Block of drain hose
* Malf un cti on of drain pu mp
* Improper connection of electric
circuit
* Malf un cti on of the th ermocoup le
Lime deposits form on the dishes
* Too much detergent * Reduce the dosage
The dishes look greasy and a blue film
fo rms on th em s omet im es
* Too much rinse agent * Reduce the dosage
Dirty spots o n the surface of the
dishwasher
* The detergent sticks to t he damp
surface
* Use th e deter g en t accor d in g t o t he
user's manual
* The detergent should not be spilled
on the surface of the dishwasher
Strange color o f the surface of the
washed dishes
* The salt is not int ended to use in
the dishwasher.
* The influe nce of salt on the resin

E8.If the distributary valve have worked for 150 seconds, and could not reach right
position during wash cycle,after the cycle is finished, the dishwasher will shut off all
loads, the alarm buzzer will ring for 30 seconds and the window will display "E8" at rate
of 1Hz in 30 seconds, and then display "E8" , drain water for 2 minutes meanwhile
2.3 Notes
5
Program button: To select one of the six programs. .
1
2
3
4
3in1 and half load function button: To select and show 3in1
and Half load functions. (Half load function means that the
lower spray arm does not run, so you should load the upper
basket only ).
Display window: Program remaining time, delay time,
running indicator, Program indicator, Salt and rinse
aid indicator, Error codes, etc.
Power switch: To turn on/off the power supply.
2345
Delayed Start Button: To preset the wash timer and delay
the starting time up to 24 hours. Every press of this button
increases the time by one hour.
for example: one press for an hour, two for two
hours... ...
（
）
Control Panel
11
Auto
3 in13 in1
Error Codes
Codes Possible Causes
Tap is not opened, or water intake is restricted,or water pressure
is too low.
E1
Too much inlet water.
Meanings
Longer inlet time.
Overfilled.
E4
When some malfunctions come on, the appliance will display error codes to warn you: