Kenwood KMM-118 User manual

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
For your records
Record the serial number, found on the back of the unit, in the spaces
designated on the warranty card, and in the space provided below.
Refer to the model and serial numbers whenever you call upon your
Kenwood dealer for information or service on the product.
Model KMM-118
Serial number
US Residents Only
Register Online
Register your Kenwood product at http://www.kenwood.com/usa/
B5A-1340-00 (KN)© 2016 JVC KENWOOD Corporation
KMM-118
DIGITAL MEDIA RECEIVER
INSTRUCTION MANUAL
RÉCEPTEUR MULTIMÉDIA NUMÉRIQUE
MODE D’EMPLOI
RECEPTOR DE MEDIOS DIGITALES
MANUAL DE INSTRUCCIONES
JS_KWD_KMM_118_KN_C_2.indd 1JS_KWD_KMM_118_KN_C_2.indd 1 23-Aug-16 2:42:30 PM23-Aug-16 2:42:30 PM

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
2
CONTENTS BEFORE USE
IMPORTANT
•
To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe
Warning and Caution in this manual.
•
Please keep the manual in a safe and accessible place for future reference.
WARNING
•
Do not operate any function that takes your attention away from safe driving.
•
Do not ingest the battery, Chemical Burn Hazard
The remote control supplied with this product contains a coin/button cell battery.
If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
Caution
Volume setting:
•
Adjust the volume so that you can hear sounds outside the car to prevent accidents.
•
Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.
General:
•
Avoid using the external device if it might hinder safe driving.
•
Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.
•
Never put or leave any metallic objects (such as coins or metal tools) inside the unit, to prevent a short circuit.
•
Depending on the types of cars, the antenna will automatically extend when you turn on the unit with the antenna control wire connected
( 16) . Turn off the unit or change the source to STANDBY when parking at a low ceiling area.
Remote control (RC-406):
•
Do not leave the remote control in hot places such as on the dashboard.
•
The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.
•
The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
How to read this manual
•
Operations are explained mainly using buttons on the faceplate.
•
English indications are used for the purpose of explanation. You can select the display language from the [FUNCTION] menu. ( 5)
•
[XX] indicates the selected items.
•
( XX) indicates references are available on the stated page.
BEFORE USE 2
BASICS 3
GETTING STARTED 4
1 Select the display language
and cancel the demonstration
2 Set the clock and date
3 Set the initial settings
RADIO 5
USB/iPod/ANDROID 7
AUX 9
AUDIO SETTINGS 10
DISPLAY SETTINGS 11
TROUBLESHOOTING 12
REFERENCES 13
Maintenance
More information
INSTALLATION/
CONNECTION 14
SPECIFICATIONS 17
ENGLISH
JS_KWD_KMM_118_KN_EN_4.indd 2JS_KWD_KMM_118_KN_EN_4.indd 2 24-Aug-16 9:25:33 AM24-Aug-16 9:25:33 AM

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
3
BASICS
To On the faceplate On the remote control
Turn on the power Press .
• Press and hold to turn off the power.
Press and hold SRC to turn off the power.
( Pressing SRC does not turn on the power. )
Adjust the volume Turn the volume knob. Press or .
• Press and hold to continuously increase
the volume to 15.
Press ATT during playback to attenuate the sound.
• Press again to cancel.
Select a source Press repeatedly. Press SRC repeatedly.
Change the display information* Press DISP repeatedly.
( 14) ( Not available )
*
You can also turn off the display information by pressing DISP repeatedly.
Faceplate
How to resetAttach Detach
Remote control (RC-406)
ENGLISH
Display window
Pull out the
insulation sheet
when using for
the first time.
Your preset adjustments will
be erased except stored radio
stations.
How to replace the battery
Remote sensor (Do not
expose to bright sunlight.)
Volume knob
Detach button *
Not used
JS_KWD_KMM_118_KN_EN_4.indd 3JS_KWD_KMM_118_KN_EN_4.indd 3 24-Aug-16 9:25:34 AM24-Aug-16 9:25:34 AM

4
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
GETTING STARTED
Select the display language and cancel the demonstration
When you turn on the power (or after you reset the unit), the display
shows: “SEL LANGUAGE” “PRESS” “VOLUME KNOB”
1 Turn the volume knob to select [ENG] (English) or [SPA] (Spanish),
then press the knob.
[ENG] is selected for the initial setup.
Then, the display shows: “CANCEL DEMO” “PRESS” “VOLUME
KNOB”.
2 Press the volume knob.
[YES] is selected for the initial setup.
3 Press the volume knob again.
“DEMO OFF” appears.
Set the clock and date
1 Press the volume knob to enter
[FUNCTION] .
2 Turn the volume knob to select [CLOCK] , then press the knob.
To adjust the clock
3 Turn the volume knob to select [CLOCK ADJUST] , then press the knob.
4 Turn the volume knob to make the settings, then press the knob.
Hour Minute
5 Turn the volume knob to select [CLOCK FORMAT] , then press the knob.
6 Turn the volume knob to select [12H] or [24H] , then press the knob.
1
2
To set the date
7 Turn the volume knob to select [DATE FORMAT] , then press the knob.
8 Turn the volume knob to select [DD/MM/YY] or [MM/DD/YY] , then press
the knob.
9 Turn the volume knob to select [DATE SET] , then press the knob.
10 Turn the volume knob to make the settings, then press the knob.
Day Month Year or Month Day Year
11 Press and hold to exit.
To return to the previous setting item, press .
Set the initial settings
1 Press repeatedly to enter STANDBY.
2 Press the volume knob to enter [FUNCTION] .
3 Turn the volume knob to select an item (see the following table),
then press the knob.
4 Repeat step 3until the desired item is selected or activated.
5 Press and hold to exit.
To return to the previous setting item, press .
Default:
XX
AUDIO CONTROL
SWITCH PREOUT REAR
/ SUB-W : Selects whether rear speakers or a subwoofer are
connected to the line out terminals on the rear (through an external
amplifier).
( 16)
SP SELECT OFF
/ 5/4 / 6 × 9/6 / OEM : Selects according to the speaker size (5inches
or 4inches, 6×9inches or 6inches) or OEM speakers for optimum
performance.
3
ENGLISH
JS_KWD_KMM_118_KN_EN_4.indd 4JS_KWD_KMM_118_KN_EN_4.indd 4 24-Aug-16 9:25:36 AM24-Aug-16 9:25:36 AM

ENGLISH 5
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
TUNER SETTING
PRESET TYPE NORMAL
:Memorizes one station for each preset button in each band
(FM1/FM2/FM3/AM).;
MIX :Memorizes one station for each preset
button, regardless of the selected band.
SYSTEM
KEY BEEP ON
:Activates the keypress tone.; OFF :Deactivates.
SOURCE SELECT
BUILT-IN AUX ON
:Enables AUX in source selection.; OFF :Disables. ( 9)
F/W UPDATE
UPDATE SYSTEM
F/W UP xxxx YES
:Starts upgrading the firmware.; NO :Cancels (upgrading is not
activated).
For details on how to update the firmware, visit
<www.kenwood.com/cs/ce/>.
CLOCK
CLOCK DISPLAY ON
:The clock time is shown on the display even when the unit is turned
off.;
OFF :Cancels.
ENGLISH Select the display language for [FUNCTION] menu and music information
if applicable.
By default,
[ENGLISH] is selected.
ESPANOL
GETTING STARTED RADIO
Search for a station
1 Press repeatedly to select TUNER.
2 Press repeatedly (or press / on the remote
control) to select FM1/FM2/FM3/AM.
3 Press S/T(or press S/ on the remote control) to
search for a station.
• To change the searching method for S/T: Press
repeatedly.
AUTO1 : Automatically search for a station.
AUTO2 : Search for a preset station.
MANUAL : Manually search for a station.
• To store a station: Press and hold one of the number buttons (1to6).
• To select a stored station: Press one of the number buttons (1to6) (or
press one of the number buttons (1to6) on the remote control).
Direct Access Tuning (using the remote control)
1 Press DIRECT to enter Direct Access Tuning.
2 Press the number buttons to enter a frequency.
3 Press to search for a station.
• To cancel, press or DIRECT.
• If no operation is done for 10seconds after step2, Direct Access Tuning
is automatically canceled.
JS_KWD_KMM_118_KN_EN_4.indd 5JS_KWD_KMM_118_KN_EN_4.indd 5 24-Aug-16 9:25:37 AM24-Aug-16 9:25:37 AM

6
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
RADIO
Other settings
1 Press the volume knob to enter
[FUNCTION] .
2 Turn the volume knob to select an item (see the following table),
then press the knob.
3 Repeat step 2until the desired item is selected or activated.
4 Press and hold to exit.
To return to the previous setting item, press .
Default:
XX
TUNER SETTING
AUTO
MEMORY
YES :Automatically starts memorizing 6 stations with good reception.;
NO :Cancels.
•
Selectable only if [NORMAL] is selected for [PRESET TYPE] . ( 5)
MONO SET ON
:Improves the FM reception, but the stereo effect may be lost.;
OFF :Cancels.
NEWS SET ON : The unit will temporarily switch to News Programme if available. ;
OFF :Cancels.
REGIONAL ON : Switches to another station only in the specific region using the “AF”
control.;
OFF :Cancels.
AF SET ON : Automatically searches for another station broadcasting the same
program in the same Radio Data System network with better reception
when the current reception is poor.;
OFF :Cancels.
TI ON :Allows the unit to temporarily switch to Traffic Information if available
(“TI” lights up).;
OFF :Cancels.
PTY SEARCH 1 Turn the volume knob to select the available Program Type, then press
the knob.
2 Turn the volume knob to select the PTY language ( ENGLISH / FRENCH /
GERMAN ), then press the knob.
3 Press S / T to start searching.
CLOCK
TIME SYNC ON
:Synchronizes the unit’s time to the Radio Data System station time.;
OFF :Cancels.
Available Program Type for [PTY SEARCH]
SPEECH
: NEWS , AFFAIRS , INFO (information), SPORT , EDUCATE , DRAMA ,
CULTURE , SCIENCE , VARIED , WEATHER , FINANCE , CHILDREN , SOCIAL ,
RELIGION , PHONE IN , TRAVEL , LEISURE , DOCUMENT
MUSIC
: POP M (music), ROCK M (music), EASY M (music), LIGHT M (music),
CLASSICS , OTHER M (music), JAZZ , COUNTRY , NATION M (music),
OLDIES , FOLK M (music)
The unit will search for the Program Type categorized under
[SPEECH] or
[MUSIC] if selected.
•
[MONO SET] / [NEWS SET] / [REGIONAL] / [AF SET] / [TI] / [PTY SEARCH] is selectable
only when the band is FM1/FM2/FM3.
• If the volume is adjusted during reception of traffic information or news
bulletin, the adjusted volume is memorized automatically. It will be
applied the next time traffic information or news bulletin is turned on.
ENGLISH
JS_KWD_KMM_118_KN_EN_4.indd 6JS_KWD_KMM_118_KN_EN_4.indd 6 24-Aug-16 9:25:38 AM24-Aug-16 9:25:38 AM

ENGLISH 7
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
USB/iPod/ANDROID
Start playback
The source changes automatically and
playback starts.
*1
KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type
*2
Do not leave the cable inside the car when not using.
To directly select USB/iPod/ANDROID source, press iPodUSB.
To On the faceplate On the remote control
Playback/pause Press . Press .
Reverse/Fast-forward*4Press and hold S/T. Press and hold S/ .
Select a file Press S/T. Press S/ .
Select a folder*5Press J/K.Press / .
Repeat play*6Press repeatedly.
FILE REPEAT / FOLDER REPEAT / ALL REPEAT : MP3/WMA/WAV/FLAC file
FILE REPEAT / FOLDER REPEAT / REPEAT OFF : iPod or ANDROID
Random play*6Press repeatedly.
FOLDER RANDOM / RANDOM OFF : MP3/WMA/WAV/FLAC file, iPod or
ANDROID
Press and hold to select
ALL RANDOM .
*3
When connecting an Android device, “Press [VIEW] to install KENWOOD MUSIC PLAY APP” is shown. Follow the instructions
to install the application. You can also install the latest version of KENWOOD MUSIC PLAY application on your Android device
before connecting. For more information, visit <www.kenwood.com/cs/ce/>.
*4
For ANDROID: Applicable only when [BROWSE MODE] is selected. ( 8)
*5
Only for MP3/WMA/WAV/FLAC files. This does not work for iPod/ANDROID.
*6
For iPod/ANDROID: Applicable only when [MODE OFF] / [BROWSE MODE] is selected. ( 8)
USB input terminal
CA-U1EX (max.: 500mA)
(optional accessory)
Micro USB 2.0 cable
*2
(commercially available)
KCA-iP102/KCA-iP103
(optional accessory)
*1
or accessory of the iPod/
iPhone
*2
USB
iPod/iPhone
ANDROID*3
JS_KWD_KMM_118_KN_EN_4.indd 7JS_KWD_KMM_118_KN_EN_4.indd 7 24-Aug-16 9:25:38 AM24-Aug-16 9:25:38 AM

8
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
USB/iPod/ANDROID
Select control mode
While in iPod source, press iPodUSB repeatedly.
MODE ON : Control iPod using the iPod itself. However, you can still
play/pause, file skip, fast-forward or reverse from this unit.
MODE OFF : Control iPod from this unit.
While in ANDROID source, press iPodUSB repeatedly.
BROWSE MODE : Control Android device from this unit via KENWOOD
MUSIC PLAY application installed in the Android
device.
HAND MODE : Control Android device using the Android device
itself via other media player applications installed in
the Android device. However, you can still play/pause
and file skip from this unit.
Select music drive
While in USB source, press iPodUSB repeatedly.
Stored songs in the following drive will be played back.
• Selected internal or external memory of a smartphone (Mass
Storage Class).
• Selected drive of a multiple drives device.
Select a file from a folder/list
For iPod/ANDROID, applicable only when [MODE OFF] / [BROWSE MODE]
is selected.
1 Press .
2 Turn the volume knob to select a folder/list, then press the
knob.
3 Turn the volume knob to select a file, then press the knob.
Quick Search (applicable only for USB and ANDROID source)
If you have many files, you can search through them quickly.
Turn the volume knob quickly to browse through the list quickly.
Skip Search (applicable only for iPod and ANDROID source)
Press S/Tto search at a preset skip search ratio. ( 9, [SKIP SEARCH])
• Pressing and holding S/Tsearches at a 10 % ratio.
Alphabet search (applicable only for iPod and ANDROID source)
You can search for a file according to the first character.
For iPod source
1 Turn the volume knob quickly to enter character search.
2 Turn the volume knob to select the character.
• Select “
*” to search for a character other than AtoZ, 0to9.
3 Press S/Tto move to the entry position.
• You can enter up to 3characters.
4 Press the volume knob to start searching.
For ANDROID source
1 Press J/Kto enter character search.
2 Turn the volume knob to select the character.
^A^: Upper case letters (A to Z)
_A_: Lower case letters (a to z)
-0-: Numbers (0 to 9)
***: Character other than AtoZ, 0to9
3 Press the volume knob to start searching.
• To return to the root folder/first file/top menu, press 5.
• To return to the previous setting item, press .
• To cancel, press and hold .
ENGLISH
JS_KWD_KMM_118_KN_EN_4.indd 8JS_KWD_KMM_118_KN_EN_4.indd 8 24-Aug-16 9:25:40 AM24-Aug-16 9:25:40 AM

ENGLISH 9
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
USB/iPod/ANDROID
Direct Music Search (using the remote control)
1 Press DIRECT.
2 Press the number buttons to enter a file number.
3 Press to search for music.
• To cancel, press or DIRECT.
• Not available if Random Play is selected.
• Not applicable for iPod and ANDROID source.
Listen to TuneIn Radio/TuneIn Radio Pro/Aupeo
While listening to TuneIn Radio, TuneIn Radio Pro or Aupeo, connect the
iPod/iPhone to the USB input terminal of the unit.
• The unit will output the sound from these applications.
Other settings
1 Press the volume knob to enter
[FUNCTION] .
2 Turn the volume knob to select an item (see the following table),
then press the knob.
3 Repeat step 2until the desired item is selected or activated.
4 Press and hold to exit.
To return to the previous setting item, press .
Default:
XX
USB
MUSIC DRIVE DRIVE CHANGE
:The next drive ( [DRIVE 1] to [DRIVE 5] ) is selected
automatically and playback starts.
Repeat steps
1 to 3 to select the following drives.
SKIP SEARCH 0.5% / 1% / 5% / 10% : While listening to iPod or ANDROID source, selects
the skip search ratio over the total files.
Preparation:
Select
[ON] for [BUILT-IN AUX] in [SOURCE SELECT] . ( 5)
Start listening
1 Connect a portable audio player (commercially available).
2 Press repeatedly to select AUX.
3 Turn on the portable audio player and start playback.
Set the AUX name
While listening to a portable audio player connected to the unit...
1 Press the volume knob to enter [FUNCTION] .
2 Turn the volume knob to select [SYSTEM] , then press the knob.
3 Turn the volume knob to select [AUX NAME SET] , then press the knob.
4 Turn the volume knob to select an item, then press the knob.
AUX (default)/ DVD / PORTABLE / GAME / VIDEO / TV
5 Press and hold to exit.
To return to the previous setting item, press .
AUX
Auxiliary input jack
Portable audio player
3.5mm (1/8") stereo mini plug with “L” shaped connector
(commercially available)
JS_KWD_KMM_118_KN_EN_4.indd 9JS_KWD_KMM_118_KN_EN_4.indd 9 24-Aug-16 9:25:40 AM24-Aug-16 9:25:40 AM

10
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
AUDIO SETTINGS
While listening to any source...
1 Press the volume knob to enter [FUNCTION] .
2 Turn the volume knob to select an item (see the following
table), then press the knob.
3 Repeat step 2until the desired item is selected or
activated.
4 Press and hold to exit.
To return to the previous setting item, press .
(or using the remote control)
1 Press AUD to enter [AUDIO CONTROL] .
2 Press J/Kto select an item, then press .
Default:
XX
AUDIO CONTROL
SUB-W LEVEL –15
to +15 ( 0 ) Adjusts the subwoofer output level.
BASS LEVEL –8 to +8 ( +2 )Adjusts the level to memorize for each
source. (Before making an adjustment,
select the source you want to adjust.)
MID LEVEL –8 to +8 ( +1 )
TRE LEVEL –8 to +8 ( +1 )
EQ PRO (This setting is stored to [USER] .)
BASS ADJUST BASS CTR FRQ 60 / 80 / 100 / 200 : Selects the center frequency.
BASS LEVEL –8 to +8 ( +2 ):Adjusts the level.
BASS Q FACTOR 1.00 / 1.25 / 1.50 / 2.00 :Adjusts the quality factor.
BASS EXTEND ON :Turns on the extended bass.; OFF :Cancels.
MID ADJUST MID CTR FRQ 0.5KHZ / 1.0KHZ / 1.5KHZ / 2.5KHZ :Selects the center frequency.
MID LEVEL –8 to +8 ( +1 ):Adjusts the level.
MID Q FACTOR 0.75 / 1.00 / 1.25 :Adjusts the quality factor.
TRE ADJUST TRE CTR FRQ 10.0KHZ / 12.5KHZ / 15.0KHZ / 17.5KHZ :Selects the center
frequency.
TRE LEVEL –8 to +8 ( +1 ):Adjusts the level.
PRESET EQ DRIVE EQ / TOP40 / POWERFUL / ROCK / POPS / EASY /J AZZ / NATURAL / USER :
Selects a preset equalizer suitable to the music genre. (Select
[USER] to use the
settings made in
[EQ PRO] .)
[DRIVE EQ] is a preset equalizer that reduces noise outside the car or running noise
of the tyres.
BASS BOOST LV1 / LV2 / LV3 :Selects your preferred bass boost level.; OFF :Cancels.
LOUDNESS LV1 / LV2 :Selects your preferred low and high frequencies boost to produce a well-
balanced sound at a low volume level.;
OFF :Cancels.
SUBWOOFER SET ON :Turns on the subwoofer output.; OFF :Cancels.
LPF SUBWOOFER THROUGH :All signals are sent to the subwoofer.; 85HZ / 120HZ / 160HZ :Audio
signals with frequencies lower than 85Hz/120Hz/160Hz are sent to the subwoofer.
SUB-W PHASE REVERSE (180°)/ NORMAL (0°):Selects the phase of the subwoofer output to be in
line with the speaker output for optimum performance. (Selectable only if a setting
other than
[THROUGH] is selected for [LPF SUBWOOFER] .)
ENGLISH
JS_KWD_KMM_118_KN_EN_4.indd 10JS_KWD_KMM_118_KN_EN_4.indd 10 24-Aug-16 9:25:40 AM24-Aug-16 9:25:40 AM

ENGLISH 11
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
DISPLAY SETTINGS
Set the dimmer
Press and hold DISP (DIMMER) to turn on or off the dimmer.
• If you have set
[DIMMER TIME] , it will be canceled once you press and
hold this button.
Other settings
1 Press the volume knob to enter
[FUNCTION] .
2 Turn the volume knob to select an item (see the following table),
then press the knob.
3 Repeat step 2until the desired item is selected/activated or follow
the instructions stated on the selected item.
4 Press and hold to exit.
To return to the previous setting item, press .
Default:
XX
DISPLAY
DIMMER
Dim the illumination.
ON :Dimmer is turned on.; OFF :Cancels.
DIMMER TIME :Set the dimmer on and off time.
1 Turn the volume knob to adjust the [ON] time, then press the knob.
2 Turn the volume knob to adjust the [OFF] time, then press the knob.
(Default:
[ON] : 6:00PM ; [OFF] : 6:00 AM )
BRIGHTNESS 0 to 31 : Select your preferred brightness level for display illumination.
TEXT SCROLL AUTO / ONCE :Select whether to scroll the display information
automatically, or scroll only once.;
OFF :Cancels.
FADER R15 to F15 ( 0 ):Adjusts the rear and front speaker output balance.
BALANCE L15 to R15 ( 0 ):Adjusts the left and right speaker output balance.
VOLUME OFFSET For AUX: –8 to +8 ( 0 ) ; For other sources: –8 to 0 :Preset the initial
volume level of each source. (Before adjustment, select the source you
want to adjust.)
SOUND RECNSTR
(Sound
reconstruction)
ON :Creates realistic sound by compensating the high-frequency
components and restoring the rise-time of the waveform that are lost
in audio data compression.;
OFF :Cancels.
• [SUB-W LEVEL] / [SUBWOOFER SET] / [LPF SUBWOOFER] / [SUB-W PHASE] is
selectable only if
[SWITCH PREOUT] is set to [SUB-W] . ( 4)
• [SUB-W LEVEL] / [LPF SUBWOOFER] / [SUB-W PHASE] is selectable only if
[SUBWOOFER SET] is set to [ON] . ( 10)
AUDIO SETTINGS
JS_KWD_KMM_118_KN_EN_4.indd 11JS_KWD_KMM_118_KN_EN_4.indd 11 24-Aug-16 9:25:40 AM24-Aug-16 9:25:40 AM

12
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
TROUBLESHOOTING
Symptom Remedy
General
Sound cannot be heard.
•
Adjust the volume to the optimum level.
•
Check the cords and connections.
“MISWIRING CHECK WIRING
THEN PWR ON” appears.
Turn the power off, then check to be sure the
terminals of the speaker wires are insulated properly.
Turn the power on again.
“PROTECTING SEND SERVICE”
appears.
Send the unit to the nearest service center.
•
Sound cannot be heard.
•
The unit does not turn on.
•
Information shown on the
display is incorrect.
Clean the connectors.
( 13)
The unit does not work at all. Reset the unit. ( 3)
Radio
•
Radio reception is poor.
•
Static noise while listening
to the radio.
Connect the antenna firmly.
USB/iPod
“READING” keeps flashing. Do not use too many hierarchical levels or folders.
Elapsed playing time is not
correct.
This is caused by how the files are recorded.
Correct characters are not
displayed (e.g. album name).
•
This unit can only display uppercase letters,
numbers, and a limited number of symbols.
•
Depending on the display language you have
selected
( 5) , some characters may not be
displayed correctly.
“NA FILE” Make sure the media contains supported audio files.
( 13)
“READ ERROR” Copy the files and folders onto the USB device again.
If this does not solve the problem, reset the USB
device or use another USB device.
Symptom Remedy
USB/iPod
“NO DEVICE” Connect a USB device, and change the source to USB again.
“COPY PRO” A copy-protected file is played.
“NA DEVICE” Connect a supported USB device, and check the
connections.
“NO MUSIC” Connect a USB device that contains playable audio files.
“iPod ERROR”
•
Reconnect the iPod.
•
Reset the iPod.
ANDROID
•
Sound cannot
be heard during
playback.
•
Sound output only
from the Android
device.
•
Reconnect the Android device.
•
If in [HAND MODE] , launch any media player application
on the Android device and start playback.
•
If in [HAND MODE] , relaunch the current media player
application or use another media player application.
•
Restart the Android device.
•
If this does not solve the problem, the connected Android
device is unable to route the audio signal to unit.
( 13)
Cannot playback at
[
BROWSE MODE ].
•
Make sure KENWOOD MUSIC PLAY APP is installed on the
Android device.
( 7)
•
Reconnect the Android device and select the appropriate
control mode.
•
If this does not solve the problem, the connected Android
device does not support
[BROWSE MODE] . ( 13)
“NO DEVICE” or
“READING” keeps
flashing.
•
Switch off the developer options on the Android device.
•
Reconnect the Android device.
•
If this does not solve the problem, the connected Android
device does not support
[BROWSE MODE] . ( 13)
Playback is intermittent
or sound skips.
Turn off the power saving mode on the Android device.
“ANDROID ERROR”/
“NADEVICE”
•
Reconnect the Android device.
•
Restart the Android device.
ENGLISH
JS_KWD_KMM_118_KN_EN_4.indd 12JS_KWD_KMM_118_KN_EN_4.indd 12 24-Aug-16 9:25:41 AM24-Aug-16 9:25:41 AM

ENGLISH 13
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
REFERENCES
Maintenance
Cleaning the unit
Wipe off dirt on the faceplate with a dry silicone or soft cloth.
Cleaning the connector
Detach the faceplate and clean the connector
gently with a cotton swab, being careful not to
damage the connector.
More information
For: – Latest firmware updates and latest compatible item list
– Any other latest information
Visit <www.kenwood.com/cs/ce/>.
Playable files
•
Playable audio file for USB mass storage class device: MP3 (.mp3), WMA (.wma),
WAV (.wav), FLAC (.flac)
•
Playable USB device file system: FAT12, FAT16, FAT32
Even when audio files comply with the standards listed above, playback may be impossible
depending on the types or conditions of media or device.
•
For detailed information and notes about the playable audio files, visit
<www.kenwood.com/cs/ce/audiofiles>.
About USB devices
•
You cannot connect a USB device via a USB hub.
•
Connecting a cable whose total length is longer than 5m may result in abnormal playback.
•
This unit cannot recognize a USB device whose rating is other than 5V and exceeds 1A.
Connector (on the reverse
side of the faceplate)
About iPod/iPhone
Made for
–
iPod touch (2nd, 3rd, 4th, 5th, and 6th generation)
–
iPod classic
–
iPod nano (3rd, 4th, 5th, 6th, and 7th generation)
–
iPhone 3G, 3GS, 4, 4S, 5, 5S, 5C, 6, 6 Plus, 6S, 6S Plus, SE
•
You cannot operate iPod if “KENWOOD” or “ ” is displayed on iPod.
•
Depending on the version of the operating system of the iPod/iPhone, some functions may
not operate on this unit.
About Android device
•
This unit supports Android OS 4.1 and above.
•
Some Android devices (with OS 4.1 and above) may not fully support Android Open Accessory
(AOA) 2.0.
•
If the Android device supports both mass storage class device and AOA 2.0, this unit always
playback via AOA 2.0 as priority.
Muting upon the reception of a phone call
Connect the MUTE wire to your telephone using a commercial telephone accessory. ( 16)
When a call comes in, “CALL” appears.
(The audio system pauses.)
•
To continue listening to the audio system during a call, press . “CALL” disappears
and the audio system resumes.
When the call ends, “CALL” disappears. (The audio system resumes.)
JS_KWD_KMM_118_KN_EN_4.indd 13JS_KWD_KMM_118_KN_EN_4.indd 13 24-Aug-16 9:25:42 AM24-Aug-16 9:25:42 AM

14
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
REFERENCES
Change the display information
Each time you press DISP , the display information changes.
•
If the information is unavailable or not recorded, “NO TEXT”, “NO INFO”, or other information
(eg. station name, playing time) appears.
Source name Display information
STANDBY Source name (*) Clock (back to the beginning)
TUNER Frequency (*) Clock (back to the beginning)
(For FM Radio Data System stations only)
Station name (*) Radio text Radio text+ Title/Artist
Frequency Clock (back to the beginning)
USB
(For MP3/WMA/WAV/FLAC files)
Music title/Artist (*) Album title/artist Folder name
File name Playing time Clock (back to the beginning)
iPod or ANDROID When
[MODE OFF] / [BROWSE MODE] is selected. ( 8)
Music title/Artist (*) Album title/Artist Playing time
Clock (back to the beginning)
AUX Source name (*) Clock (back to the beginning)
*
Turn off the display information.
Warning
•
The unit can only be used with a 12V DC power supply, negative ground.
•
Disconnect the battery’s negative terminal before wiring and mounting.
•
Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire
(black) to prevent a short circuit.
•
Insulate unconnected wires with vinyl tape to prevent a short circuit.
•
Be sure to ground this unit to the car’s chassis again after installation.
Caution
•
For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer.
•
Install this unit in the console of your vehicle. Do not touch the metal parts of this unit during
and shortly after use of the unit. Metal parts such as the heat sink and enclosure become hot.
•
Do not connect the [ wires of speakers to the car chassis or Ground wire (black), or connect
them in parallel.
• Mount the unit at an angle of less than 30º.
•
If your vehicle wiring harness does not have the ignition terminal, connect Ignition wire (red)
to the terminal on the vehicle’s fuse box which provides 12 V DC power supply and is turned
on and off by the ignition key.
•
Keep all cables away from heat dissipate metal parts.
•
After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are
working properly.
•
If the fuse blows, first make sure the wires are not touching car’s chassis, then replace the old
fuse with one that has the same rating.
Basic procedure
1 Remove the key from the ignition switch, then disconnect the [ terminal of the car
battery.
2 Connect the wires properly.
See Wiring connection.
( 16)
3 Install the unit to your car.
See Installing the unit (in-dash mounting).
( 15)
4 Connect the [ terminal of the car battery.
5 Reset the unit. ( 3)
INSTALLATION/CONNECTION
ENGLISH
JS_KWD_KMM_118_KN_EN_4.indd 14JS_KWD_KMM_118_KN_EN_4.indd 14 24-Aug-16 9:25:42 AM24-Aug-16 9:25:42 AM

ENGLISH 15
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Do the required wiring.
( 16)
Dashboard of
your car
Bend the appropriate tabs to hold the
mounting sleeve firmly in place.
How to remove the unit
1 Detach the faceplate.
2 Remove the trim plate.
3 Insert the extraction keys deeply into the slots on each side,
then follow the arrows as shown on the illustration.
Installing the unit (in-dash mounting) When installing without the mounting sleeve
1 Remove the mounting sleeve and trim plate from the unit.
2 Align the holes in the unit (on both sides) with the
vehicle mounting bracket and secure the unit with screws
(supplied).
Use only the specified screws. Using wrong screws might
damage the unit.
Hook on the top side
Orientate the trim plate as
illustrated before fitting.
INSTALLATION/CONNECTION
Part list for installation
(A) Faceplate (C) Mounting sleeve (B) Trim plate
(D) Wiring harness (E) Extraction key (F) Screws
JS_KWD_KMM_118_KN_EN_4.indd 15JS_KWD_KMM_118_KN_EN_4.indd 15 24-Aug-16 9:25:47 AM24-Aug-16 9:25:47 AM

16
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Wiring connection
Fuse (10A)
Car fuse box
Car fuse box
Battery
Ignition switch
Blue/White
(Power control wire/
Antenna control wire)
(12 V 350 mA)
Light blue/yellow
(Steering remote
control wire)
Red (Ignition wire)
Yellow (Battery wire)
Black (Ground wire)
To the metallic body or chassis of the car
To the power control terminal when using
the optional power amplifier or to the
antenna control terminal in the vehicle
Brown
(Mute control wire)
White
Gray
Green
Purple
White/Black
Gray/Black
Green/Black
Purple/Black
To the terminal that is grounded when the
telephone rings or during conversation.
( 13)
(To connect the Kenwood navigation system,
refer your navigation manual.)
To front speaker (left)
To rear speaker (left)
To front speaker (right)
To rear speaker (right)
If no connections are made, do not let the wire come out from the tab.
To the steering wheel remote control
adapter
When connecting to an external amplifier, connect
its ground wire to the car’s chassis to avoid damaging
the unit.
IMPORTANT: We recommend installing the unit with a
commercially available custom wiring harness specific
for your car and leave this job to professionals for your
safety. Consult your car audio dealer.
INSTALLATION/CONNECTION
Output terminals
Antenna terminal
ENGLISH
JS_KWD_KMM_118_KN_EN_4.indd 16JS_KWD_KMM_118_KN_EN_4.indd 16 24-Aug-16 9:25:47 AM24-Aug-16 9:25:47 AM

ENGLISH 17
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
SPECIFICATIONS
Tuner
FM Frequency Range 87.5 MHz — 108.0 MHz (50 kHz space)
Usable Sensitivity (S/N=26dB) 8.2dBf (0.71μV/75Ω)
Quieting Sensitivity
(DINS/N=46dB)
17.2dBf (2.0μV/75Ω)
Frequency Response (±3dB) 30 Hz — 15 kHz
Signal-to-Noise Ratio (MONO) 64 dB
Stereo Separation (1kHz) 40dB
AM Frequency Range 530kHz — 1700kHz (10kHz space)
Usable Sensitivity (S/N=20dB) 29dBμ (28.2μV)
USB
USB Standard USB1.1, USB2.0 Full Speed
File System FAT12/16/32
Maximum Supply Current DC5V 1A
Frequency Response (±1dB) 20Hz — 20kHz
Signal-to-Noise Ratio (1kHz) 105 dB
Dynamic Range 88dB
Channel Separation 90dB
MP3 Decode Compliant with MPEG-1/2 Audio Layer-3
WMA Decode Compliant with Windows Media Audio
WAV Decode Linear-PCM
FLAC Decode FLAC file (Up to 48kHz/16bit)
Audio
Maximum Output Power 50W×4
Full Bandwidth Power 22W×4 (at less than 1% THD)
Speaker Impedance 4Ω—8Ω
Tone Action Bass 100Hz±8dB
Middle 1.0kHz±8dB
Treble 12.5kHz±8dB
Preout Level/Load (USB) 2500mV/10kΩ
Preout Impedance ≤600Ω
Auxiliary
Frequency Response (±3dB) 20Hz—20kHz
Input Maximum Voltage 1000mV
Input Impedance 30kΩ
General
Operating Voltage 14.4V (10.5V—16V allowable)
Maximum Current Consumption 10A
Operational Temperature Range –10°C—+60°C
Installation Size (W×H×D) 182mm×53mm×114mm
(7-3/16"×2-1/16"×4-1/2")
Net Weight (includes Trimplate,
Mounting Sleeve)
0.6kg (1.2lbs)
Subject to change without notice.
JS_KWD_KMM_118_KN_EN_4.indd 17JS_KWD_KMM_118_KN_EN_4.indd 17 24-Aug-16 9:25:48 AM24-Aug-16 9:25:48 AM

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
2
TABLE DES MATIERES
AVANT L’UTILISATION
IMPORTANTES
•
Pour utiliser correctement l’appareil, veuillez ce manuel complément avant de l’utiliser. Il est particulièrement important que vous lisiez et acceptiez les avertissements et les
précautions de ce manuel.
•
Veuillez garder ce manuel dans un endroit sûr et accessible pour une utilisation future.
MISE EN GARDE
•
N’utilisez aucune fonction qui risque de vous distraire de la conduite sure de votre véhicule.
•
Ne pas ingérer la pile. Risque de brûlures chimiques.
La télécommande fournie avec ce produit contient une pile bouton.
Une ingestion de la pile bouton risque de provoquer de graves brûlures internes en seulement 2 heures ; brûlures qui risquent d’entraîner le décès.
Conservez les piles neuves et usagées hors de portée des enfants.
Si le compartiment des piles ferme mal, n’utilisez plus le produit et conservez-le hors de portée des enfants.
Si vous pensez que des piles ont été ingérées ou insérées dans une quelconque partie du corps, contactez immédiatement un médecin.
Précautions
Réglage du volume:
•
Ajustez le volume de façon à pouvoir entendre les sons extérieurs à la voiture afin d’éviter tout risque d’accident.
•
Réduisez le volume avant de reproduire des sources numériques afin d’éviter d’endommager les enceintes par la soudaine augmentation du niveau de sortie.
Généralités:
•
Éviter d’utiliser le périphérique extérieur s’il peut gêner une conduite en toute sécurité.
•
Assurez-vous que toutes les données importantes ont été sauvegardées. Nous ne pouvons pas être tenu responsable pour toute perte des données enregistrées.
•
Veuillez faire en sorte de ne jamais mettre ou laisser d’objets métalliques (tels que des pièces ou des outils) dans l’appareil, afin d’éviter tout risque de court-circuit.
•
En fonction du type de voiture, l’antenne s’étendra automatiquement quand vous mettrez l’appareil sous tension si le câble de commande d’antenne est connecté ( 16) .
Mettez l’appareil hors tension ou changez la source sur STANDBY quand vous vous garez dans un parking avec un plafond bas.
Télécommande (RC-406):
•
Ne laissez pas la télécommande dans des endroits exposés à la chaleur, comme sur le tableau de bord par exemple.
•
La pile au lithium risque d’exploser si elle est remplacée incorrectement. Ne la remplacez uniquement qu’avec le même type de pile ou son équivalent.
•
Le boîtier de la pile ou les piles ne doivent pas être exposés à des chaleurs excessives telles que les rayons du soleil, du feu, etc.
Comment lire ce manuel
•
Les opérations sont expliquées principalement en utilisant les touches de la façade.
•
Les indications en anglais sont utilisées dans un but explicatif. Vous pouvez choisir la langue d’affichage à partir du menu [FUNCTION] . ( 5)
•
[XX] indique les éléments choisis.
•
( XX) indique que des références sont disponibles aux page citées.
AVANT L’UTILISATION 2
FONCTIONNEMENT DE BASE 3
PRISE EN MAIN 4
1 Sélectionne la langue
d’affichage et annule la
démonstration
2 Réglez l’horloge et la date
3 Faites les réglages initiaux
RADIO 5
USB/iPod/ANDROID 7
AUX 9
RÉGLAGES AUDIO 10
RÉGLAGES D’AFFICHAGE 11
GUIDE DE DÉPANNAGE 12
RÉFÉRENCES 13
Entretien
Plus d’informations
INSTALLATION/
RACCORDEMENT 14
SPÉCIFICATIONS 17
FRANÇAIS
JS_KWD_KMM_118_KN_FR.indd 2JS_KWD_KMM_118_KN_FR.indd 2 24/8/2016 10:36:15 AM24/8/2016 10:36:15 AM

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
3
FONCTIONNEMENT DE BASE
Pour Sur la façade Sur la télécommande
Mettez l’appareil sous tension
Appuyez sur .
• Maintenez la touche enfoncée pour mettre l’appareil hors tension.
Maintenez
SRC enfoncée pour mettre l’appareil hors tension.
( Appuyer sur
SRC ne met pas l’appareil sous tension. )
Ajustez le volume Tournez le bouton de volume. Appuyez sur ou .
• Maintenez enfoncé de façon continue pour
augmenter le volume sur 15.
Appuyez sur
ATT pendant la lecture pour atténuer le son.
• Appuyez une nouvelle fois pour annuler.
Sélectionner la source
Appuyez répétitivement sur .Appuyez répétitivement sur
SRC .
Changez l’information sur
l’affichage*
Appuyez répétitivement sur DISP . ( 14)
( Non disponible )
*
Vous pouvez aussi mettre hors service les informations sur l’affichage en appuyant répétitivement sur DISP .
Façade
Comment réinitialiserAttachez Détachez
Télécommande (RC-406)
FRANÇAIS
Fenêtre d’affichage
Retirez la feuille
d’isolant lors de la
première utilisation.
Vos ajustements préréglés seront
effacés sauf les stations radio
mémorisées.
Comment remplacer la pile
Capteur de télécommande (Ne
l’exposez Pas à la lumière directe
du soleil.)
Bouton de volume
Touche de détachement
*
Non utilisé
JS_KWD_KMM_118_KN_FR.indd 3JS_KWD_KMM_118_KN_FR.indd 3 24/8/2016 10:36:16 AM24/8/2016 10:36:16 AM

4
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
PRISE EN MAIN
Sélectionne la langue d’affichage et annule la
démonstration
Quand vous mettez l’appareil sous tension (ou après une réinitialisation de l’appareil),
l’affichage apparaît:“SEL LANGUAGE” “PRESS” “VOLUME KNOB”
1 Tournez le bouton de volume pour sélectionner [ENG] (anglais) ou [SPA]
(espagnol), puis appuyez sur le bouton.
[ENG] est choisi pour le réglage initial.
Puis, l’affichage montre: “CANCEL DEMO” “PRESS” “VOLUME KNOB”.
2 Appuyez sur le bouton de volume.
[YES] est choisi pour le réglage initial.
3 Appuyez de nouveau sur le bouton de volume.
“DEMO OFF”apparaît.
Réglez l’horloge et la date
1 Appuyez sur le bouton de volume pour entrer
[FUNCTION] .
2 Tournez le bouton de volume pour choisir [CLOCK] , puis appuyez sur le
bouton.
Pour ajuster l’horloge
3 Tournez le bouton de volume pour choisir [CLOCK ADJUST] , puis appuyez
sur le bouton.
4 Tournez le bouton de volume pour faire les réglages, puis appuyez sur le
bouton.
Heure Minute
5 Tournez le bouton de volume pour choisir [CLOCK FORMAT] , puis appuyez
sur le bouton.
6 Tournez le bouton de volume pour choisir [12H] ou [24H] , puis appuyez
sur le bouton.
1
2
Pour régler la date
7 Tournez le bouton de volume pour choisir [DATE FORMAT] , puis appuyez
sur le bouton.
8 Tournez le bouton de volume pour choisir [DD/MM/YY] ou [MM/DD/YY] ,
puis appuyez sur le bouton.
9 Tournez le bouton de volume pour choisir [DATE SET] , puis appuyez sur le
bouton.
10 Tournez le bouton de volume pour faire les réglages, puis appuyez sur le
bouton.
Jour Mois Année ou Mois Jour Année
11 Maintenez enfoncée pour quitter.
Pour retourner à l’option de réglage précédente, appuyez sur .
Faites les réglages initiaux
1 Appuyez répétitivement sur pour entrer en veille STANDBY.
2 Appuyez sur le bouton de volume pour entrer [FUNCTION] .
3 Tournez le bouton de volume pour sélectionner un élément (voir le
tableau suivant), puis appuyez sur le bouton.
4 Répétez l’étape 3jusqu’à ce que l’élément souhaité soit sélectionné ou
activé.
5 Maintenez enfoncée pour quitter.
Pour retourner à l’option de réglage précédente, appuyez sur .
Défaut:
XX
AUDIO CONTROL
SWITCH PREOUT REAR
/ SUB-W : Choisit si les enceintes arrière ou un caisson de grave sont connectés aux
prises de sortie de ligne à l’arrière (à travers un amplificateur extérieur).
( 16)
SP SELECT OFF
/ 5/4 / 6 × 9/6 / OEM : La sélection est faite en fonction de la taille des enceintes
(5 pouces ou 4 pouces, 6×9 pouces ou 6 pouces) ou des enceintes OEM pour obtenir une
performance optimale.
3
FRANÇAIS
JS_KWD_KMM_118_KN_FR.indd 4JS_KWD_KMM_118_KN_FR.indd 4 24/8/2016 10:36:16 AM24/8/2016 10:36:16 AM