Kettler 7162-490 User manual

Stockholm GT Table Tennis Table
Model 7162-490/890 & 7122-490/890
Adult Assembly Required
Picture Similar
Made in Germany
KETTLER® International, Inc. 1355 London Bridge Road Virginia Beach, VA 23453 USA
www.kettlerusa.com
[email protected]om
Please do not return this product to
the store. Contact KETTLER® for
parts and service: call toll free
866.804.0440 or send email to
[email protected]om.
Please visit our website
www.kettlerusa.com to view a video
demonstration of product assembly
or scan the QR Code above.
Tools needed; not included

2
All KETTLER®products are designed in accordance with the latest safety regulations and undergo a constant process of quality
control during manufacturing. The knowledge gained in this process is used to constantly improve and develop our products. In
order to offer our customers the very best in product quality, we reserve the right to make technical changes at any time. In spite
of this, should you have any cause for complaint, please contact KETTLER®.
Note on Safety
Handling the Equipment
Before Assembly
Before assembling or using the table tennis table, please read the following instructions carefully. They contain important information for
use and maintenance of the equipment as well as for your personal safety. Keep these instructions in a safe place for maintenance
purposes or for ordering spare parts.
The table tennis table should be used only for its
intended purpose, i.e. for playing with suitable table
tennis racquets and balls.
All other uses are prohibited and may be dangerous.
The manufacturer cannot be held liable for damage
or injury caused by improper use of the table.
Damage or worn components may endanger your
safety or shorten the lifespan of the table tennis
table. Replace worn or damaged components
immediately and remove the table from use until
this has been done. Use only spare parts
manufactured by KETTLER®.
The table tennis table complies with all safety
regulations. Incorrect repairs, alterations to the
design (removal of original parts, addition of other
components etc.) may endanger the safety of the
user.
Instruct other persons (in particular children) using
the table in its correct use, and draw their attention
to any potential source of danger, especially when
setting up or dismantling the table.
Caution: During assembly, keep all items out of
children’s reach (choking hazard – contains small
parts).
When setting up or dismantling the table, stay clear of
its folding radius.
When folded up, the table tennis table presents a
large surface to the wind. For this reason, ensure that
it is stored in a sheltered position.
The table tennis table may be pushed only in the
transport position otherwise there is a risk of injury.
The unit complies with the standard
EN 4468-1:2004.
Regularly check all screws, bolts, etc. to ensure they
are in good condition.
Warning: Children should not attempt to fold/unfold
table. May result in injury
Do not use the table tennis table until it has been
fully and correctly assembled and checked.
Ensure that indoor table tennis tables are not
exposed to dampness or rain. Keep them well away
from direct sources of heat. Should the surface
become warped, lay the table on a level surface for a
few days.
Set the table up on a level surface.
Do not cover it with a tarp, which can result in
condensation forming. We recommend the
weatherproof KETTLER® cover, part number 7032-
900. Cover should only be used when table is in
folded position.
For practicing without a partner, the table halves can
be folded up individually.
Do not use corrosive or abrasive materials to clean the
equipment. Ensure that such materials are not
allowed to pollute the environment. In most cases, a
slightly dampened cloth is sufficient.
Waste Disposal: KETTLER® products are recyclable. At
the end of its useful life, please dispose of correctly
and safely complying with your local facilities and
guidelines.
Store table in folded position when not in use.

3
General Assembly Instructions
Before Assembly (continued)
The equipment must be assembled with care by two
adults.
Separate all the parts including the hardware.
Compare quantities with the package contents
section and that all items are undamaged. If there
are any problems, please contact KETTLER®.
Before assembling the equipment, study the
drawings and photos carefully then assemble in the
order shown.
Please note that there is always a danger of injury
when working with tools or doing manual work.
Therefore, please be careful during assembly.
Ensure that your working area is free of possible
sources of danger, for example don’t leave any tools
lying around. Always dispose of packaging material
in such a way that it may not cause any danger.
There is always a risk of suffocation if children play
with plastic bags!
The fastening items required for each assembly step
are shown at the beginning of the step. Use the
fastening items exactly as instructed.
Bolt all the parts together loosely at first, and check
that they have been assembled correctly. Then use
spanner for final tightening. Then check that all
screw connections have been tightened firmly.
For technical reasons, we reserve the right to carry
out preliminary assembly work (e.g. addition of
tubing plugs).
Please keep original packaging, so that it may be
used for transport at a later date, if necessary.
Goods may only be returned after prior arrangement
and in packaging that is safe for transportation (in
the original box if possible). It is important to
provide a detailed defect description/damage
report.
Package Contents
Number Included - 2
Number Included - 2
Number Included - 2
Number Included - 1
Number Incl –4 non locking
Number Incl –4 locking
Number Included - 2
Number Included - 2
Number Included - 3
Number Included - 2
Number Included - 2

4
Items below are shown at actual size
Package Contents (continued)
Number Included –2 of each
Number Included - 2
Number Included - 2
Number Included - 2
Number Included - 6
Number Included - 2
Number Included - 4
Number Included –4
m8x110
Number Included –4
m6x100
Number Included –6
m8x60
Number Included –6
3.9x13
Number Included –2
m6x58
Number Included –4
m6x49
Number Included –4
m8x125
Number Included - 2
Tool included
Not shown at
actual size
2
2

5
Items below are shown at actual size
Number Included –4
m6x45
Number Included –4
m5x65
Package Contents (continued)
Number Incl –8
m8
Number Incl –4
m6x3mm
Number Incl –2
Number Incl –10
dia 25x8
Number Incl –24
dia 16x8
Number Incl –8
dia 12x6
Number Incl –4
m12x6x3
End view and side view shown
Number Incl –4
m12x6x15
Number Incl –4
Number Incl –4
m5 locking
Number Incl –4
dia 12x5
Number Incl –6
m6
Number Incl –2
Number Incl –4
End view and side view shown
Number Incl –4
m6x5mm
Number Incl –4
m6

6
Begin the assembly of your table by carefully removing
the plastic wrap and all of the loose contents. Separate
the two table tops by removing the four plastic corner
protectors and the plastic side strips.
Step 1
Align footlock with stemtube.
Insert drift pin. There are two footlocks and
stemtubes. Assemble both as shown.
Assembly
A
B
C
2 Required
2 Required
2 Required

7
Step 2
Install stemtubes to wheelbases
as shown.
Begin by installing locking stemtube
to wheelbase (A-H)
Repeat for non-locking stemtube
as shown in I.
Assembly
A
G
D
E
F
C
B
H
I
16x8
25x8
16x8
m8
4 Required
m8x125
4 Required
dia 25x8
8 Required
dia 16x8
4 Required
m8
4 Required

8
Step 3
Install non-locking wheels.
Do not over torque; wheels should roll smoothly.
Install non-locking wheels on both wheelbase assemblies.
Assembly
2 Required
m8x110
2 Required
m8
8 Required
dia 16x8
A
B
C
D
E

9
Step 4
Install locking wheels.
The grooves of the wheels should face inward.
Do not over torque; wheels should roll smoothly.
Install locking wheels on both wheelbase assemblies.
2 Required
m8x110
2 Required
m8
8 Required
dia 16x8
Assembly
A
B
D
C
E

10
Step 5
Assemble net posts as shown.
Assembly
C
B
A
I
G
D
H
F
E
J
4 Required
m6x3mm
4 Required
m6x45

11
Step 6
Install H-pads to alignment strut (A-F).
Insert nut into strut (G-J).
Secure strut to wheelbase (K-U).
Repeat for opposite side.
Assembly
4 Required
m5 locking
B
A
J
C
H
K
G
D
E
F
I
L
4 Required
m5
locking
4 Required
m6
4 Required
dia 12x5
4 Required
m5x65
m5
locking

12
Step 6 (continued)
Assembly
M
O
N
Q
P
R
U
T
S
m5x65
12x5
12x5
m6
m6
m5x65

13
Step 7
Lock wheels.
Step 8
Bolt Crossbar to Wheelbases as shown.
Upon completing Step 8, assembly should match F.
Assembly
B
F
A
B
C
A
E
D
2 Required
m8x60
2 Required
dia 25x8

14
Step 9
Assembly
C
B
A
D
G
E
F
Important: Have two people complete Steps 9-13. With assistance, lift one table top
onto the wheelbase; the legs will be facing outward. Have one person support the top
while it is resting on the base while the other person completes assembly.
Assemble crossbar to Jbars and support leg in the order shown. Note: a Jbar with safety
lever should be assembled on the right side) and a Jbar without lever on the left side.
The support leg is always assembled closest to the wheelbase. You may need to lower
table slightly to line up the bolt holes. Do not fully tighten the bolts until both ends are
assembled.
Jbar
Support
Leg
Jbar
Support
Leg
2 Required
dia 25x8
2 Required
m8x60

15
Step 10
C
B
A
Assembly
Install plug into crossbar as shown.
End view and side view shown
2 Required
m6x5mm

16
Step 11
Assembly
D
C
B
A
I
G
H
E
F
Raise safety lever up straight. Bolt the safety lever to leg.
2 Required
dia 12x6
1 Required
m6x58
1 Required
m6

17
Step 12
Assembly
A
B
C
D
E
G
F
Bolt the Jbars to leg.
End view and side view shown
2 Required
m12x6x15
2 Required
m12x6x3
2 Required
m6x100

18
Step 13
A
Assembly
B
G
C
H
D
E
F
Bolt locking struts to support leg. Repeat for left side of top as shown in H.
Carry out steps 9-13
again for the other side.
2 Required
m6x49
2 Required
dia 12x6
2 Required
m6

19
Step 14
Open Table Top to Complete Assembly
AssemblyAssembly
B
A
D
A
B
J
C
Install handgrips as shown.
To properly open table into playing position: lock wheels. Push the thumb latch down on the locking strut.
Squeeze the strut on the right side and lower table into playing position. Support the table as you lower it; never
allow it to drop down.
E

20
Step 15
Net Assembly
Assembly
A
B
C
B
A
D
C
F
E
G
Screw sideshroud into place. Repeat installation of the
second shroud on opposite side of wheelbase assembly.
Slide Jpin through net (A, B). Place Jpin in designated slots (C). Tie string to tension tab (D).
Place string in slots over Jpin and net post. Adjust net tension by adjusting tension tab (E).
Screw Adjuster into underside of net post (F, G).
6 Required
3.9x13
3 screws