Kettler PL33 User manual

Assembly Instructions
3.3m LED Free Arm Parasol
PL33
August 2021
IMPORTANT
PLEASE KEEP THIS BOOKLET FOR FUTURE REFERENCE.
THIS IS IMPORTANT INFORMATION REGARDING THE
USE AND CARE OF YOUR GARDEN FURNITURE. ASSEMBLY
TIME
PERSONS
REQUIRED
30
MINUTES

Parts List
Helpful advice before you begin:
1. We suggest you spend a short time reading through this leaet and then follow the simple
step by step instructions.
2. Do not discard any of the packaging until you have checked that you have all the parts and
the pack of ttings.
3. Assemble this product on a soft surface.
4. To ensure an easier assembly, we strongly advise that all ttings are only nger tightened
during initial assembly. Only upon completion of the assembly should all xing points
be fully tightened.
5. Keep ttings out of children’s reach.
6. Do not use any other tools other than those recommended to build this product.
7. Please do not use substitute parts. Use only additional or replacement parts supplied by Kettler.
8. In the unlikely event that this product has missing or damaged parts, please visit our website
www.kettler.co.uk
A
H
D E
C
DD
BB
CC
CC
B
EE J
E1
DD
AA
I
CCAA BB DD EE
Part Description Qty
A Parasol 1
AA Large Allen Key 1
B Solar Panel 1
BB Small Allen Key 1
C Rotating Hub 1
CC Bolt 6
D Metal Stand 2
DD Washer 6
E Plastic Base Interior 2
E1 Plastic Base Exterior 2
EE Crank Handle 1
FF Base Plug 4
G Pole Cap 1
H Protective Cover with 3
part supporting rod
1
I Plug/Adapter/Cord 1
J Wireless Speaker 1

Assembly
12
AA
D
CC
DD
FF
EE1
Open
Sand Water
Close
Each section of the
base requires 20kg of
sand and then needs
to be topped up with
water. Water alone will
not support the base.
Tip: use kiln dried
sand for easier lling.
DC

Assembly
D
E
CE1
E1
You may need to
re-position the pedal
at this stage to t
the base sections
together.
G
B
1
4
2
3
The solar panel clicks in and twists.
The solar panel will require 8
hours of sunlight to become fully
charged. To charge from at the
solar lights will be required to be
switched o. When the solar panel
is not in regular use, remove and
replace with the cap.
3
4

Assembly
BB
BB
EE
A
C
E
CC
AA
DD
5
6

Operating Instructions
1
2
Storage Tie
Crank clockwise
to open,
counter-clockwise
to close.
CAUTION: DO NOT
open the parasol
counter-clockwise.
It will not stay open
and may close
unexpectedly.
CAUTION: When
cranking the parasol
open, if you feel
resistance and
the canopy is not
opening, do not
force the crank
handle. Gently
spread the ribs by
hand and shake the
fabric, then continue
to crank open.
1
2

Operating Instructions
To operate LED lights, press the rocker switch located on
the Umbrella (A) pole on or o.
Note:
a) The Solar Panel (B) contains two lithium batteries
(2 x 2200mAh). Press the switch to the o position
during daylight to allow the solar panel to charge the
batteries. Charging time is dependent on the amount
of sunlight, however, 8 hours is recommended.
b) The batteries can also be charged using the AC
Adapter (I) by plugging it into the Umbrella (A) pole
as shown.Charging time is approximately 5-6 hours.
c) If the batteries are dead, the lights will operate with
the AC Adapter (I) plugged in. The red light on the AC
Adapter (I) indicates power is present and the battery
is charging.
d) Keep the umbrella unplugged and the AC Adapter (I)
stored in a dry location when not in use.
A
C
Light Switch
I
3
4

Operating Instructions
Changing an LED light strip.5
Disassembly
Assembly
2
2
3
3
1
1

Operating Instructions
The parasol should be closed and the night cover tted in windy
conditions and when not in use. Failure to do this may result in
damage to the parasol.
The night cover
ts over the
canopy and
frame.
6
1. 2.
Protective cover assembly:
Fiberglass
supporting
rod
Assemble the 3 part bleglass rods
in sequence and insert into the slit in
fabric at bottom of zip.
Place cover over the parasol and
frame and zip down.
H

Parasol Wireless Speaker with LED Lights
Functions
1. Bluetooth Button
2. LED Light Power Button
3. Unlock Button
4. LED Light
5. Charging Port
1
2
3
4
5
Charging:
• Charge for 2-4 hours for the 1st charge.
• Plug the adapter in the charging port and plug into the power supply (100-240V).
• When charging the red light will light up and go o when fully charged.
• Always charge in a dry environment.
User guide:
• To turn on, hold down the power button for 3 seconds.
• Turn on your device’s Bluetooth function and search for “Kettler”.
• The run time is approx. 6-10 hours.
• To turn the light on/o press the “LED” button.
Warning:
• Bluetooth connectivity will turn o when not used for 15 minutes.
• The sound quality will be reduced when the battery is low.
• Use wirelessly for upto 8 - 10 metre range. Any more than this will aect the sound quality.
• Only one device can be connected at any one time.
• Do not allow the speaker unit to get wet.
• Store in a dry place when not in use.
1234