Keymantek K25 User manual

K25 Hand Held Terminal
MANUAL
ShenZhen Keymantek Co.,Ltd.
2011

1
Warning ：
：：
：Please read the followings before operating the terminal.
Do not take the battery out when it is charging.
Disassembling the terminal and/or any damage to the surface
should void the
warranty.
Keep the display screen free from any kind of stress. Keymantek is not responsible
for that damages.
Back up data in time.
Keymantek is not responsible for any loss because of losing
data when the terminal is using.
Keep the terminal away from static and/or strong electromagnetic radiation.
There is a lithium-ion battery in the terminal.
Do not try to disassemble ,crush or
pierce the battery. Dispose the battery according to local law or EHS guidance.
Do not install any other program,except permitted by Keymantek.
The material in this manual is subject to change without notice.

2
Contents
Chapter 1 Quick Guide
Introduction………………………………………………………………… ……4
1.1 Performance………………………………………………….4
1.2 Buttons……………………………………………………......5
1.3 Accessories………………………………………………………8
1.4 Keyboard instructions………………………………………………8
Chapter 2 Getting Started
2.1 Install and change battery………………………………………..10
2.2 Power on and off……………………………………………….....10
2.3 Charge the battery……….……………………………………..13
2.4 Sleep & Wakeup………………………………….……………..14
2.5 askbar…………………………………………………………...15
2.6 Desktop………………………………………………………...16
2.7 Reset the terminal…………………………………………….17
Chapter 3 System Settings
3.1 PDT Settings……………………………………………………..19

3
3.2 Power Management ………………………………………….21
3.3 Security Setting………………………………………………..23
3.4 Regional Settings……………………………………………...24
3.5 Date/Time……………………………………………………....27
3.6 Ownership settings…………………………………….………28
3.7System…………………………………………………………..30
3.8 Display……………………… ………………………………..33
Chapter 4 Keyboard & Input modes
4.1 Key board………………………………………………………34
4.2 Input Panel…………………………………………………….34
Chapter 5 Software installation&uninstall
5.1 Directories……………………………………………………..35
5.2 Install Microsoft ActiveSync………………………………….35
5.3 Install software……………………………………………….. 36
Appendix 1 Trouble shooting……………………………………………37
Appendix 2 Maintenance……………………………………………….38
Appendix 3 Customer Service…………………………………………...38
Appendix 4 Others………………………………………………………..38

4
1.1Performance
Item Description
OS Microsoft Windows CE.Net 5.0
CPU s3c2440 405 MHz Processor
Memory 512M Flash ROM, 64M/128M RAM
Display
QVGA 2.8 240 x320 resolution, Transflective, portrait
mode TFT High-reliability adjustable LED
function
IRDA METER
additional SYMBOL engine(1D)
additional RFID (13.56M)
Backup SD card & FLASH
Develop
environment MS EVC 4.0 & VS.NET 2008
Battery 4400mAh lithium-ion battery
IP & Drop test Test per IEC60529/IP65, 1.5
meter/6 times drop to
concrete
Temperature Operatingtemperature:-20℃
℃℃
℃-50℃
℃℃
℃
Storage temperature:-20℃
℃℃
℃to 55℃
℃℃
℃
Communicate on USB /Wifi/CDMA/GPIS/Bluetooth optional
Storage Micro SD card（
（（
（4GB）
））
）

5
Dimensions 196mm*58/75mm*33/42mm
Weight 405g
1.2 Buttons
Key Action
Power key.Press the key to turn the terminal on when
off.Pr
ess the key to enter suspend/wakeup status.Press the
key for 3 seconds to turn the terminal off.
Combination function key
Combination function key
Scan button
Direction key-Left
Direction key-Right
Direction key-Up
TAB Direction key-Down
Executes a selected item.

6
ENTER KEY
TAB as PC
Backspace key
Numeric-1
Numeric-2/Letter-ABC
Numeric-3/Letter-DEF
Numeric-4/Letter-GHI
Numeric-5/Letter-JKL
Numeric-6/Letter-MNO
Numeric-7/Letter-PQRS
Numeric-8/Letter-TUV
Numeric-9WXYZ

7
Numeric-0
*
Symbols cycle
radix point,space or others
Switch input method
As star key on PC
Combination function key with other keys
1.3 Accessories
Item Quantity Remark
Terminal 1pc
Stylus 1pc
USB cable 1pc
Allows USB connection from the terminal to a
host computer,allows charging of the terminal
through the cable.
Charger 1pc For charging the battery and set
Lithium-ion
battery
1pcs

8
1.4 Keyboard instructions
Ⅰ
ⅠⅠ
Ⅰ:Trigger Function keys
1Left-right side key and intermediate large orange key-press, default for
scanning global hotkey(When have scanning function)
2PWR for indicator light, the buttons. RST for reset button.
3No. * keys for '. 'and' * 'two button cycle, # # key symbol for the following
circular'. ', '`','~', '! 'and' @ ', '#', '$',' % ', '^', '&', '*', '(',') ', '-', '_', '=', '+',
'\ \', '|', '[',' {', '] ', '} ', ', ', ':', '\', '\ "', ', 'and' < ', '>', '/', '?"
4The Shift is only switch input method to use
5Fn used only as a key combination
Ⅱ
ⅡⅡ
Ⅱ:Multifunction button
1Lower red switch machine key, in shutdown state system boots, boot state
as long press out shutdown menu, optional choose system dormancy,
shutdown.
20-9 in digital input states output figures. 1-9 in lowercase state output
lowercase letters, capital state output capital letters. 1 in letters state output
symbols and '#' same, but opposite in order, from hind cycle. 0 in letters
state output Spaces.
Ⅲ
ⅢⅢ
Ⅲ:Key combination
1Key combination method of use, first press Fn, then click on the other keys,
loosen the first loosen other key.

9
2Fn + (1-8) output keys for F1 - F10, also used for macro, can be in control
panel Settings.In the control panel set up corresponding application
procedures and opens, through the press this key combination can be
directly to activate the application.
3Fn + upper-left corner green button, can be enabled keyboard backlighting.
4Fn + top-r red buttons, it may prohibit keyboard backlighting.
5Fn + ENT permitted use touch-screens.
6Fn + LEFT reduce screen backlighting brightness, Fn + u-right increase
screen backlighting brightness.
7Fn + DOWN the key value VK_VOLUME_DOWN and reduce the volume,
Fn + UP the key value VK_VOLUME_UP that increasing the volume, Fn +
ESC key/value VK_VOLUME_MUTE muting switch out.
8Fn + # out the blank space key
9Fn + TAB out key value ALT + TAB (system default can mix the task
manager).
Chapter 2 Getting Start
2.1 Installing & Changing Battery
1. Be sure that the Terminal is turned off.
2. Unlock the Battery Cover.
3. Remove the Battery Cover.
4. Insert battery in the battery compartment with the tie on

10
the battery.
5. Replace the battery cover by inserting the top first.
6. Lock the Battery Lock
2.2 Power on & Power off
1. Power on
Insert battery in the battery compartment，
，，
，Press the
button，
，，
，then the splash screen displays（
（（
（See Figure 2-1），
），），
），When
the initialization finish，
，，
，then you can see the WinCE（
（（
（See Figure
2-2）
））
）.
Figure 2-1 Figure 2-2
Please calibrate the screen when turning on the terminal for
the first time.
(1)Click the button on the desktop，
，，
，Select
"Settings"->"Control Panel"。
。。
。

11
(2)Select "Stylus"(See Figure2-3)，
，，
，and double-click。
。。
。
Figure 2-3
(3)Select“Calibration”，
，，
，then click the “Recalibrate”button(See
Figure2-4)。
。。
。
Figure 2-4
(4)Press and hold the tip of stylus on the center of each
target appears on the screen。
。。
。

12
Figure 2-5
You can recalibrate the screen at anytime.
2. Power off
Please close all programs before turning the terminal off.
Press button for more than 3 seconds,the display will be
closed, Power LED is off, terminal closed.
2.3 Charging the Battery
1. Put the battery into cradle linked to a power source and
charge the battery.
2. Insert the battery into the terminal compartment and charge

13
the battery.
Note：
：：
：Turn the terminal off before charging.
When the picture（
（（
（See Figure 2-6-1/Figure 2-6-2）
））
）appears ,battery
need to be recharged.
Figure 2-6-1 Figure 2-6-2
2.4 Sleep & Wakeup
1. Sleep
Just press (less than 3 seconds)to set the terminal in sleep
stae when the terminal is on.Keyboard and/or touchpad does not
respond unless the terminal wakes up.
The terminal will sleep if there is no operation for a long time
when the terminal is on.See 3.2 for setting the time.
2. Wakeup

14
Press to wake the terminal when the terminal is in sleep
mode
Note：
：：
：Frequently press in a short time(10 seconds)may result in
losing data and display damage.
2.5 Taskbar
The Taskbar at the bottom of the window displays the active
programs，
，，
，See Figure2-7：
：：
：
Figure 2-7
Start Icon is used to quickly start a program,find a
file,access the settings window or access help.（
（（
（See Figure 2-8）。
）。）。
）。
Figure 2-8
Icon，
，，
，is used to toggle betwen different input modes(with
input panel)

15
Figure 2-9 Figure 2-10
Icon，
，，
，to indicate current task,toggle between different tasks.
Figure 2-11
Icon,is used to indicate the current time.You can also change it
by double-clicking the icon.Select ->"Settings"->"Taskbar and
Start Menu"-“Show Clock” to show/hide the clock.
Figure 2-12 Figure 2-13

16
2.6 Desktop
The desktop window appears when power on the termnal
A menu will appear when you keep pressing the touchpad
Figure 2-14
Figure 2-15 Figure 2-16
Desktop

17
2.7 Resetting the Terminal
If the terminal stops responding to input,reset it.
Insert the stylus into Reset Port（
（（
（See Figure 1-2）
））
）for more
than 1 second to reset the terminal.You can also release battery ,
install battery and power it on to reset.
Chaper 3 Settings
To view available options for your terminal settings,tap
-"Settings"-"Control Panel".
Figure 3-1 Figure 3-2
The following table lists the applications available in the Control
Panel.

18
Icon Description
View the PDT settings and change the PDT settings.
Calibrate the touch screen.See C
hapter 2.5 for more
information.
View battery status and change power management
options.
Change owener's password and set security options.
Set how numbers,currencies,dates,and times are
displayed.
Change date,time and time zone information.

19
Change owener's personal profiles.
View system information,and change memory settings.
Display settins, set desktop background, appearance,
backlight,and brightness.
Note：
：：
：Do not change the settings which is not on the above table.
3.1 PDT Settings
Select "Control Panel"-" Settings" to change PDT settings.(See
Figure 3-3/Figure 3-4).
PDTAttribute:Display terminal system data.
Figure 3-3 Figure 3-4