Huawei ETS1160 User manual

Notice
Copyright © Huawei Technologies Co., Ltd.
2009. All rights reserved.
1No part of this document may be reproduced or
transmitted in any form or by any means without
prior written consent of Huawei Technologies
Co., Ltd.
2The product described in this manual may
include copyrighted software of Huawei Technol-
ogies Co., Ltd and possible licensors. Customers
shall not in any manner reproduce, distribute,
modify, decompile, disassemble, decrypt,
extract, reverse engineer, lease, assign, or subli-
cense the said software, unless such restrictions
are prohibited by applicable laws or such actions
are approved by respective copyright holders
under licenses.
3
Trademarks and Permissions
4HUAWEI, and are trademarks or
registered trademarks of Huawei Technologies
Co., Ltd.
5Other trademarks, product, service and
company names mentioned are the property of
their respective owners.
6
Notice
7Some features of the product and its accessories
described herein rely on the software installed,
capacities and settings of local network, and
may not be activated or may be limited by local
network operators or network service providers,
thus the descriptions herein may not exactly
match the product or its accessories you pur-
chase.
8Huawei Technologies Co., Ltd reserves the right
to change or modify any information or specifica-
tions contained in this manual without prior
notice or obligation.
9
NO WARRANTY
10 THE CONTENTS OF THIS MANUAL ARE PRO-
VIDED “AS IS”. EXCEPT AS REQUIRED BY
APPLICABLE LAWS, NO WARRANTIES OF
ANY KIND, EITHER EXPRESS OR IMPLIED,

INCLUDING BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABIL-
ITY AND FITNESS FOR A PARTICULAR PUR-
POSE, ARE MADE IN RELATION TO THE
ACCURACY, RELIABILITY OR CONTENTS OF
THIS MANUAL.
11 TO THE MAXIMUM EXTENT PERMITTED BY
APPLICABLE LAW, IN NO CASE SHALL HUA-
WEI TECHNOLOGIES CO., LTD BE LIABLE
FOR ANY SPECIAL, INCIDENTAL, INDIRECT,
OR CONSEQUENTIAL DAMAGES, OR LOST
PROFITS, BUSINESS, REVENUE, DATA,
GOODWILL OR ANTICIPATED SAVINGS.
Import and Export Regulations
12 Customers shall comply with all applicable
export or import laws and regulations and will
obtain all necessary governmental permits and
licenses in order to export, re-export or import
the product mentioned in this manual including
the software and technical data therein.

Table of Contents 1
Introduction 1
Packing List................................................1
Front View..................................................1
Rear View...................................................2
Installation 3
Installing the Battery...................................3
Installing the SIM/USIM Card.....................3
Installing the Power Adapter ......................4
Installing the Antenna.................................4
Connecting the Terminal............................4
Viewing the Signal Strength.......................5
Mounting the FWT......................................6
General Functions 7
Booting the FWT ........................................7
Making or Answering Calls.........................7
Adjusting the Voice Volume .......................7
Advanced Functions 9
Supplementary Services ............................9
Wireless Data Service................................9
Security ....................................................10
Troubleshooting 11
Warnings and Precautions 12
1Table of Contents

1
1Introduction
Packing List
Note
To access the Internet, you need to purchase
the required data suite. For more information,
please consult your local sales agent.
Front View
Note
The figures are only for your reference, please
refer color and shape to product.
The main ports on the host are described as follows:
The LEDs on the host are described as follows:
Item Quantity
FWT (Fixed Wireless Terminal) host 1
Power adapter 1
Phone cable 1
Battery (Rechargeable) 1
Certificate of Quality 1
User Guide 1
Antenna(Optional) 1
NO. Item
1FWT switch
2Telephone port 1
3Telephone port 2
4Data port
5DC input
6Antenna port

Rear View
2
Rear View
NO. Item
7Signal strength indicator: L2
8Signal strength indicator: L1
9Battery indicator
Steady on and in red: The battery is fully
electricity or fully charged.
Fast blinking in red: The battery needs
to be recharged.
Slow blinking in red: The battery is being
charged.
10 Power indicator
Steady on and in blue: The FWT is con-
nected with the power adapter.
11 Network mode
Double blinking in blue: searching the
network.
Blinking in blue: registering with the 2G
network.
Steady on and in blue: registering with
the 3G network.
No. Item
1Wall-mounting brackets
2SIM/USIM card slot
3Battery container
4Battery port
5Battery container cover

3
2Installation
Note
Before installing or removing the battery,
antenna, or SIM/USIM card, you need to swich
off the FWT and disconnect the FWT from the
power adapter.
Installing the Battery
Note
• When the ambient temperature exceeds the
temparature allowed for charging, the system
will stop charging the battery.
• When the power adapter is in use, the FWT
will automatically charge the battery and stop
charging when the battery is fully charged.
• Remove the battery if the FWT is left unused
for a long period.
• Make sure that the battery has been charged
for more than 8 hours before it supplies
power for the FWT at the first time. The
charging time depends on the environmental
temperature and battery life.
Insert the connection cable of the battery into the bat-
tery port (make sure the battery is correctly inserted),
and then seat the battery in the battery container.
Installing the SIM/USIM Card
Note
• Consult the local agent to determine whether
to install the SIM/USIM card or not.
•TheSIM/USIM card and contact point are vul-
nerable to damage such as scarring or bend-
ing, so you need to insert or remove it with
care.
Insert the card into the card slot. Put the side with a
corner cutting backwards and the side with a golden
contact downwards. Make sure the card is completely
inserted into the slot.

Installing the Power Adapter
4
Installing the Power Adapter
In normal conditions, the FWT relies on the external
power adapter for power supply.
1Insert one end of the power adapter into the DC
input port, and the other end into the power sup-
ply jack.
2If the power indicator is in blue, the connection
is correct.
Use the battery only in the case that the electricity
has failed or the external power adapter is unavail-
able. You must make sure that the battery has been
fully charged before putting it into use.
Installing the Antenna
1Make sure that the FWT is switchedoff.
2Align the antenna with the antenna port on the
FWT host in the direction shown in the figure,
and then screw the antenna, ensuring that the
connection is secure.
Connecting the Terminal
Note
• Switch off the FWT and disconnect the power
adapter.
• Use the cable provided by the manufacturer.

Viewing the Signal Strength
5
Connecting the FWT to a Telephone
The FWT provides two telephone ports. They are in
parallel connection and use the same number.
Note
To avoid the call effect from interfering by the
wireless signal, place the telephone one meter
away from the FWT
Connecting the FWT to a PC
After purchasing the data service suite, you can use
data services by connecting the FWT to a PC, and
maintain the FWT on the PC. For details, consult
your local agent.
Viewing the Signal Strength
Power on the FWT and wait until some signal
strength indicators are on or until you can hear the
dial tone.
• If all signal strength indicators remain off for 5 minutes
and only the fault tone is heard. No signals can be
received.
• Turn the antenna but all signal LEDs still keep off. The
signal quality is very poor. If the dial tone can be heard
in some area, position the antenna towards it.
Indicators Signal Level Signal Strength
L1 and L2
remain off 0No signal

Mounting the FWT
6
The required signal strength is level 1 or above.
Note
• If the L2 is fast blinking in blue, it indicates
that the SIM/USIM card is not in place, the
SIM/USIM card is faulty, the PIN code is
locked, or the PIN code is not entered.
• If the signal strength is in level 1 or 3, the sig-
nal strength indicators of level 1 or 3 should
be on for 80 percent of the time.
Mounting the FWT
Horizontal Mounting
Place the FWT on a smooth surface with cool air and
good ventilation. Keep the FWT away from other
objects around for at least 10 cm.
Vertical Mounting
Fix wall screws into the wall with the screw heads
extending approximately 3 mm from the surface of
the wall, align the mounting brackets with the screws,
push the host towards the wall, and mate the brack-
ets with the screws, ensuring the host is stable.
L1 is steady on
and in blue 1Weak
L2 is steady on
and in blue 3Medium
L1 and L2 are
steady on and in
blue
5Strong
Indicators Signal Level Signal Strength

7
3General Functions
Booting the FWT
The boot process of the FWT will last about 20 sec-
onds. Then you can view the signal strength.
Note
If the signal strength indicators remain off, the
FWT may be faulty or not in coverage area.
Please consult the local agent.
Making or Answering Calls
1Before off-hook, make sure at least one signal
strength LED is on.
2Dial the number in either of the following ways:
• Dial a telephone number in a regular way, and the
number will be dialed out in several seconds.
• Dial all the digits of the number plus one #. The
FWT will immediately dial the number.
3Make sure to hook on the telephone in place, so
that you can receive calls.
Adjusting the Voice Volume
You can adjust the voice volume either when the tele-
phone is in standby mode or working mode. Four vol-
ume levels are available, with level 1 being the lowest
and level 4 the highest.
Adjusting the Volume in Standby
Mode
1Hook off and you can hear the dial tone, which
means the telephone service is available.
2Press #*1 to adjust the volume.
3Press keys from 1 to 4 to select the desired vol-
umn. The keys from 1 to 4 represents volumn
level from 1 to 4.
4After selecting the desired volume, press * key
to save it. If you hear the confirmation tone of a
"toot", you have successfully set the volume
level.