Keysight Technologies 1169A User manual

N5425A
ZIF Head
N5426A ZIF Tip
]1169A: 12 GHz
]1168A: 10 GHz
BANDWIDTH
] Very small fine-pitch targets.
] Low cost solder tips for probing multiple
test points.
] Full BW.
] Slightly higher loading than solder-in head.
N5380B
SMA
]1169A: 12 GHz
]1168A: 10 GHz
BANDWIDTH
] Preserves scope channels for measuring
differential signals (vs. A-B).
] Inherent cable loss compensation.
] Common mode termination voltage can be
supplied.
] Offset SMA cables adapt to variable spacing.
] Full BW.
Probe either differential or
single-ended signals
01169-21304
0.005 inch
steel wire (2)
N5382A
Differential Browser
] Best solder-in connection for differential and
single-ended signals.
] Lowest capacitance.
] Wires must be cut to proper lengths
(see user’s guide).
]1168A: 10 GHz
]1169A: 12 GHz
BANDWIDTH
N5381A
Solder-In
Differential
Head
01169-81301
0.007 inch
tin-plated
nickle wire (2) Probe either differential or
single-ended signals
] Best solder-in connection for differential and
single-ended signals.
] Lowest capacitance.
] Wires must be cut to proper lengths
(see user’s guide).
]1169A: 12 GHz
]1168A: 10 GHz
BANDWIDTH





Connecting the Probe to the Infiniium Scope

1. With the lever in relaxed in position push the probe onto the BNC.
2. The lever moves towards the R (release) and returns to symbol.
3. Move the lever towards the symbol until snug.
To Connect To Disconnect

Move and hold the lever at R
(release) and pull the probe from
the BNC.
♦ 90000 X and Q Series (with N5442A adapter)
♦ 86100C/D Series (with N1022A/B adapter)
♦ 80000B Series
♦ 90000A Series
Download the comprehensive 1168/9A
user’s guide from the probe’s product
page on www.keysight.com. The user’s
guide is also available in Keysight’s Probe
Resource Center (PRC) which is available
at www.keysight.com/find/PRC. The PRC
is an application that runs on a PC, Mac,
or iOS device.
Probe CompatibilityLocate the User’s Guide
1. Differential Solder-In 2. Differential Brower 3. SMA Probe Head 4. N5425A ZIF Head / N5426A ZIF Tip
Recomended Probe Head Configurations (Listed in order of best performance)
1168/9A InfiniiMax II Probes

Keysight Technologies
Printed in USA
01168-92006
July 2013
*01168-92006
] Maximum Input Voltage: 30V Peak, CAT I.
Maximum non-destructive voltage on each
input ground.
] To protect the probe from damage, read the
Probe Handling section in the user’s guide.
] Refer to the user’s guide for additional
safety and handling information.
] Probes are ESD sensitive devices particularly
at the probe heads. Follow standard ESD
precautions when handling.
]1169A: 5.2 GHz
]1168A: 5.2 GHz
BANDWIDTH E2675A
Differential
browser probe
head
01131-62107
91Ω resistor
probe tips (2) Tab to adjust the distance
between probe tips
] More general purpose browser than N5382A
for differential and single-ended signals.
] Lower BW and higher capacitance than
N5382A.
]1169A: 12 GHz
]1168A: 10 GHz
BANDWIDTH
] Best socketed connection for differential and
single-ended signals.
] Slightly higher capacitance than solder-in
head.
] Resistors must be cut to proper lengths
(see user’s guide).
Probe either
differential or
single-ended
signals
E2678A
Socketed
Differential
Head
0700-2348
0W mini-axial
lead resistors (2)
E2677A
Solder-In
Differential
Head
0700-2352
91Ωmini-axial
lead resistors (2)
Probe either differential or
single-ended signals
] Acceptable solder-in connection for
differential and single-ended signals. N5381A
is preferred.
] Higher capacitance than N5381A.
] Resistors must be cut to proper lengths
(see user’s guide).
]1169A: 12 GHz
]1168A: 10 GHz
BANDWIDTH
N5425A
ZIF Head
N5451A ZIF Tip
11 mm Resistor Leads
]0º tip span: ~5 GHz
]60º tip span: ~3.3a GHz
BANDWIDTH
] 11 mm leads provide extra long reach.
] Accommodate variable-pitch targets.
] Soldered to circuit.
N5425A
ZIF Head
N5451A ZIF Tip
7 mm Resistor Leads
]0º tip span: ~9.9 GHz
]60º tip span: ~4.4 GHz
BANDWIDTH
] 7 mm leads provide long reach.
] Accommodate variable-pitch targets.
] Soldered to circuit.
N5425A
ZIF Head
N2884A ZIF Tip
22 Micron Wires
]1169A: 12 GHz
]1168A: 10 GHz
BANDWIDTH
] High fidelity, high BW differential probing of
active IC.
] Flat frequency response over entire 12 GHz
BW.
] Greater rejection of common-mode noise due
to use of local adjacent ground or node.
] Requires the N5425A ZIF head.
5. N2884A Fine Wire ZIF Tip
9. Differential Socketed
6. N5451A Long-Wire ZIF TIP (7 mm)
10. Differential Brower Probe Safety Information
7. N5451A Long-Wire ZIF TIP (11 mm) 8. Differential Solder-In
Additional Configurations