Keysight Technologies M9155C PXI User manual

Keysight M9155/6/7C PXI
Hybrid Coaxial Switch Module
(DC to 26.5 GHz) and M9161D
PXI Solid State Switch Module
(50 MHz to 20 GHz)
Startup and
Service Guide

2 Keysight M9155/6/7C and M9161D Startup and Service Guide
Notices
© Keysight Technologies 2010-2016
No part of this manual may be
reproduced in any form or by any
means (including electronic storage
and retrieval or translation into a
foreign language) without prior
agreement and written consent from
Keysight Technologies as governed by
United States and international
copyright laws.
Manual Part Number
M9157-90001
Edition
Edition 4, November 25, 2016
Printed in Malaysia
Published by:
Keysight Technologies
Bayan Lepas Free Industrial Zone,
11900 Penang, Malaysia
Sales and Technical Support
To contact Keysight for sales and
technical support, refer to the support
links on the following Keysight
websites:
www.keysight.com/find/PXIswitch
(product-specific information and
support, software and documentation
updates)
www.keysight.com/find/assist
(worldwide contact information for
repair and service)
Declaration of Conformity
Declarations of Conformity for this
product and for other Keysight
products may be downloaded from the
Web. Go to http://www.keysight.com/
go/conformity. You can then search by
product number to find the latest
Declaration of Conformity.
Warranty
THE MATERIAL CONTAINED IN THIS
DOCUMENT IS PROVIDED "AS IS,"
AND IS SUBJECT TO BEING
CHANGED, WITHOUT NOTICE, IN
FUTURE EDITIONS. FURTHER, TO THE
MAXIMUM EXTENT PERMITTED BY
APPLICABLE LAW, KEYSIGHT
DISCLAIMS ALL WARRANTIES, EITHER
EXPRESS OR IMPLIED WITH REGARD
TO THIS MANUAL AND ANY
INFORMATION CONTAINED HEREIN,
INCLUDING BUT NOT LIMITED TO THE
IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. KEYSIGHT
SHALL NOT BE LIABLE FOR ERRORS
OR FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES IN
CONNECTION WITH THE
FURNISHING, USE, OR
PERFORMANCE OF THIS DOCUMENT
OR ANY INFORMATION CONTAINED
HEREIN. SHOULD KEYSIGHT AND THE
USER HAVE A SEPARATE WRITTEN
AGREEMENT WITH WARRANTY
TERMS COVERING THE MATERIAL IN
THIS DOCUMENT THAT CONFLICT
WITH THESE TERMS, THE WARRANTY
TERMS IN THE SEPARATE
AGREEMENT WILL CONTROL.
Technology Licenses
The hardware and/or software
described in this document are
furnished under a license and may be
used or copied only in accordance with
the terms of such license.
Restricted Rights Notices
If software is for use in the performance
of a U.S. Government prime contract or
subcontract, Software is delivered and
licensed as "Commercial computer
software" as defined in DFAR
252.227-7014 (June 1995), or as a
"commercial item" as defined in FAR
2.101(a) or as "Restricted computer
software" as defined in FAR 52.227-19
(June 1987) or any equivalent agency
regulation or contract clause. Use,
duplication or disclosure of Software is
subject to Keysight Technologies'
standard commercial license terms,
and non-DOD Departments and
Agencies of the U.S. Government will
receive no greater than Restricted
Rights as defined in FAR
52.227-19(c)(1-2) (June 1987). U.S.
Government users will receive no
greater than Limited Rights as defined
in FAR 52.227-14 (June 1987) or DFAR
252.227-7015 (b)(2) (November 1995),
as applicable in any technical data.

Keysight M9155/6/7C and M9161D Startup and Service Guide 3
General Safety Information
The following safety precautions should be observed before using this product
and any associated instrumentation.
This product is intended for use by qualified personnel who recognize shock
hazards and are familiar with the safety precautions required to avoid any possible
injury. Read and follow all installation, operation, and maintenance information
carefully before using this product. Refer to the user documentation for complete
product specifications.
The types of product users are:
– Responsible body who is the individual or group responsible for the use and
maintenance of equipment, for ensuring that the equipment is operated within
its specifications and operating limits, and for ensuring that operators are
adequately trained.
– Operators who use the product for its intended function. They must be trained
in electrical safety procedures and proper use of the instrument. They must be
protected from electric shock and contact with hazardous live circuits.
– Maintenance personnel who perform routine procedures on the product to
keep it operating properly (for example, setting the line voltage or replacing
consumable materials). Maintenance procedures are described in the user
documentation. The procedures explicitly state if the operator may perform
them. Otherwise, they should be performed only by service personnel.
– Service personnel who are trained to work on live circuits, perform safe
installations, and repair products. Only properly trained service personnel may
perform installation and service procedures.
Keysight products are designed for use with electrical signals that are rated
Measurement Category I and Measurement Category II, as described in the
International Electrotechnical Commission (IEC) Standard IEC 60664.
WARNING
If this product is not used as specified, the protection provided by the
equipment could be impaired. This product must be used in a normal
condition (in which all means for protection are intact) only.

4 Keysight M9155/6/7C and M9161D Startup and Service Guide
Most measurement, control, and data I/O signals are rated Measurement
Category I and must not be directly connected to mains voltage or to voltage
sources with high transient over-voltages. Measurement Category II connections
require protection for high transient over-voltages often associated with local AC
mains connections. Assume all measurement, control, and data I/O connections
are for connection to Category I sources unless otherwise marked or described in
the user documentation.
Exercise extreme caution when a shock hazard is present. Lethal voltage may be
present on cable connector jacks or test fixtures. The American National
Standards Institute (ANSI) states that a shock hazard exists when voltage levels
greater than 30 Vrms, 42.4 Vpeak, or 60 VDC are present. A good safety practice
is to expect that hazardous voltage is present in any unknown circuit before
measuring.
Operators of this product must be protected from electric shock at all times. The
responsible body must ensure that operators are prevented access and/or
insulated from every connection point. In some cases, connections must be
exposed to potential human contact. Product operators in these circumstances
must be trained to protect themselves from the risk of electric shock. If the circuit
is capable of operating at or above 1000 V, no conductive part of the circuit may
be exposed.
Do not connect switching cards directly to unlimited power circuits. They are
intended to be used with impedance-limited sources. NEVER connect switching
cards directly to AC mains. When connecting sources to switching cards, install
protective devices to limit fault current and voltage to the card.
Before operating an instrument, ensure that the line cord is connected to a
properly-grounded power receptacle. Inspect the connecting cables, test leads,
and jumpers for possible wear, cracks, or breaks before each use.
When installing equipment where access to the main power cord is restricted,
such as rack mounting, a separate main input power disconnect device must be
provided in close proximity to the equipment and within easy reach of the
operator.
For maximum safety, do not touch the product, test cables, or any other
instruments while power is applied to the circuit-under-test. ALWAYS remove
power from the entire test system and discharge any capacitors before connecting
or disconnecting cables or jumpers, installing or removing switching cards, or
making internal changes, such as installing or removing jumpers.

Keysight M9155/6/7C and M9161D Startup and Service Guide 5
Do not touch any object that could provide a current path to the common side of
the circuit-under-test or power line (earth) ground. Always make measurements
with dry hands while standing on a dry, insulated surface capable of withstanding
the voltage being measured.
The instrument and accessories must be used in accordance with its
specifications and operating instructions, or the safety of the equipment may be
impaired.
Do not exceed the maximum signal levels of the instruments and accessories, as
defined in the specifications and operating information, and as shown on the
instrument or test fixture panels, or switching card.
When fuses are used in a product, replace with the same type and rating for
continued protection against fire hazard.
Chassis connections must only be used as shield connections for measuring
circuits, NOT as safety earth ground connections.
If you are using a test fixture, keep the lid closed while power is applied to the
device-under-test. Safe operation requires the use of a lid interlock.
Instrumentation and accessories shall not be connected to humans.
Before performing any maintenance, disconnect the line cord and all test cables.
To maintain protection from electric shock and fire, replacement components in
mains circuits — including the power transformer, test leads, and input jacks —
must be purchased from Keysight. Standard fuses with applicable national safety
approvals may be used if the rating and type are the same. Other components
that are not safety-related may be purchased from other suppliers as long as they
are equivalent to the original component (note that selected parts should be
purchased only through Keysight to maintain accuracy and functionality of the
product).
If you are unsure about the applicability of a replacement component, call a
Keysight office for information.
WARNING
No operator serviceable parts inside. Refer servicing to qualified personnel.
To prevent electric shock, do not remove covers.

6 Keysight M9155/6/7C and M9161D Startup and Service Guide
Front and Rear Panel Symbols
The CE mark is a registered trademark
of the European Community. This CE
mark shows that the product complies
with all the relevant European Legal
Directives.
ICES/NMB-001 indicates that this
ISM device complies with the
Canadian ICES-001.
Cet appareil ISM est conforme a la
norme NMB-001 du Canada.
ISM GRP.1 Class A indicates that
this is an Industrial Scientific and
Medical Group 1 Class A product.
The RCM mark is a registered
trademark of the Australian
Communications and Media Authority.
This instrument complies with the
WEEE Directive (2002/96/EC)
marking requirement. This affixed
product label indicates that you
must not discard this electrical or
electronic product in domestic
household waste.
This symbol indicates the time period
during which no hazardous or toxic
substance elements are expected to
leak or deteriorate during normal use.
Forty years is the expected useful life
of the product.
This symbol indicates that PXI is a
U.S. registered trademark of the
PXI System Alliance.
This equipment is Class A suitable for professional use and is for use in electromagnetic
environments outside of the home.
xxx-
xxxxxxxx

Keysight M9155/6/7C and M9161D Startup and Service Guide 7
Waste Electrical and Electronic Equipment (WEEE) Directive 2002/
96/EC
This instrument complies with the WEEE Directive (2002/96/EC) marking
requirement. This affixed product label indicates that you must not discard this
electrical or electronic product in domestic household waste.
Product category:
With reference to the equipment types in the WEEE directive Annex 1, this
instrument is classified as a “Monitoring and Control Instrument” product.
The affixed product label is as shown below.
Do not dispose in domestic household waste.
To return this unwanted instrument, contact your nearest Keysight Service Center,
or visit http://about.keysight.com/en/companyinfo/environment/takeback.shtml
for more information.

8 Keysight M9155/6/7C and M9161D Startup and Service Guide
Cleaning Precautions
WARNING
To prevent electric shock, disconnect the instrument from mains before
cleaning. Use a dry cloth or one slightly dampened with water to clean the
external case parts. Do not attempt to clean internally. To clean the
connectors, use alcohol in a well-ventilated area. Allow all residual alcohol
moisture to evaporate, and the fumes to dissipate prior to energizing the
instrument.

Keysight M9155/6/7C and M9161D Startup and Service Guide 9
Table of Contents
General Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Front and Rear Panel Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/
EC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Product category: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Cleaning Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
1 Getting Started
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Related documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Product model description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Step 1: Unpack and Inspect the M9155/6/7C and M9161D . . . . . . . . .17
ESD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Inspect for damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Return for service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Step 2: Verify M9155/6/7C and M9161D Shipment Contents . . . . . . .19
Step 3: Install the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
System requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Power up the host PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Install the software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Step 4: Install the M9155/6/7C and M9161D . . . . . . . . . . . . . . . . . . . .22
Step 5: Verify the M9155/6/7C and M9161D Operation . . . . . . . . . . . .25
2 Service and Maintenance
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Clean the connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Make good connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

10 Keysight M9155/6/7C and M9161D Startup and Service Guide
THIS PAGE HAS BEEN INTENTIONALLY LEFT BLANK.

Keysight M9155/6/7C and M9161D Startup and Service Guide 11
List of Figures
Figure 1-1 Keysight Connection Expert interface . . . . . . . . . . . . .25
Figure 1-2 Launching the SFP from the Keysight Connection Expert
26
Figure 1-3 M9155C SFP verification . . . . . . . . . . . . . . . . . . . . . . .27
Figure 1-4 M9156C SFP verification . . . . . . . . . . . . . . . . . . . . . . .28
Figure 1-5 M9157C SFP verification . . . . . . . . . . . . . . . . . . . . . . .29
Figure 1-6 M9161D SFP verification . . . . . . . . . . . . . . . . . . . . . . .30
Figure 2-1 Wrench positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Figure 2-2 Using the torque wrench . . . . . . . . . . . . . . . . . . . . . . .36

12 Keysight M9155/6/7C and M9161D Startup and Service Guide
THIS PAGE HAS BEEN INTENTIONALLY LEFT BLANK.

Keysight M9155/6/7C and M9161D Startup and Service Guide 13
List of Tables
Table 1-1 Product model description . . . . . . . . . . . . . . . . . . . . . .16
Table 1-2 System requirements . . . . . . . . . . . . . . . . . . . . . . . . . .20

14 Keysight M9155/6/7C and M9161D Startup and Service Guide
THIS PAGE HAS BEEN INTENTIONALLY LEFT BLANK.

Keysight M9155/6/7C and M9161D PXI switch module
Startup and Service Guide
15
1 Getting Started
Introduction 16
Step 1: Unpack and Inspect the M9155/6/7C and M9161D 17
Step 2: Verify M9155/6/7C and M9161D Shipment Contents 19
Step 3: Install the Software 20
Step 4: Install the M9155/6/7C and M9161D 22
Step 5: Verify the M9155/6/7C and M9161D Operation 25

1 Getting Started
16 Keysight M9155/6/7C and M9161D Startup and Service Guide
Introduction
The scope of this Startup and Service Guide is to detail the processes of receiving
and installing the M9155/6/7C PXI Hybrid Coaxial Switch Module (DC to 26.5
GHz) and M9161D PXI Solid State Switch Module (50 MHz to 20 GHz), installing
the required software, and verifying basic module operations. If you have any
inquiries after reviewing these information, contact your local Keysight
Technologies representative or contact us through our website at
www.keysight.com/find/PXIswitch.
Related documentation
This Startup and Service Guide, and the documentation listed below, can be found
on the product CD that is shipped with the product. They are also available at
www.keysight.com/find/PXIswitch.
– Help system for the Keysight M9155/6/7C and M9161D Soft Front Panel
– Help systems for the Keysight M9155/6/7C and M9161D device drivers
(IVI-C and IVI-COM, and LabVIEW G)
– Keysight M9155/6/7C and M9161D Specifications
Product model description
Table 1-1 Product model description
Model Description
M9155C PXI hybrid dual SPDT switch, DC to 26.5 GHz, unterminated
M9156C PXI hybrid dual transfer switch, DC to 26.5 GHz
M9157C PXI hybrid single SP6T switch, DC to 26.5 GHz, terminated
M9161D PXI dual SP4T solid state switch, 50 MHz to 20 GHz

Getting Started 1
Keysight M9155/6/7C and M9161D Startup and Service Guide 17
Step 1: Unpack and Inspect the M9155/6/7C and M9161D
ESD
Electrostatic discharge (ESD) can damage or destroy electronic components. All
work on electronic assemblies should be performed at a static-safe work station.
Two types of ESD protection are listed below. Purchase acceptable ESD
accessories from your local supplier.
– Conductive table-mat and wrist-strap combination
– Conductive floor-mat and heel-strap combination
Both types, when used together, provide a significant level of ESD protection. Of
the two, only the table-mat and wrist-strap combination provides adequate ESD
protection when used alone. To ensure user safety, static-safe accessories must
provide at least 1 MΩof isolation from ground.
Inspect for damage
After unpacking the M9155/6/7C and M9161D, carefully inspect the modules for
any shipping damage. Report any damage to the shipping agent immediately, as
such damage is not covered by the warranty (warranty information can be found
at the beginning of this manual).
CAUTION
The M9155/6/7C and M9161D are shipped in materials that prevent static
damage to the modules. The modules should only be removed from the
packaging in an anti-static area ensuring that correct anti-static precautions
are taken. Store all modules in anti-static envelopes when not in use.
WARNING
These techniques for a static-safe work station should not be used when
working on circuitry with a voltage potential greater than 500 volts.
CAUTION
To avoid damage when handling a module, do not touch the exposed
connector pins.

1 Getting Started
18 Keysight M9155/6/7C and M9161D Startup and Service Guide
Return for service
Should it become necessary to return the M9155/6/7C and M9161D for repair or
service, follow these steps:
1Review the warranty information shipped with your module.
2Contact Keysight to obtain a Return Material Authorization (RMA) and return
address. If you need assistance in finding Keysight contact information, go to
www.keysight.com/find/assist (worldwide contact information for repair and
service) or refer to the Support information on the product Web page at
www.keysight.com/find/PXIswitch.
3Write the following information on a tag and attach it to the malfunctioning
module.
– Name and address of owner. A P.O. box is not acceptable as a return
address.
– Product model number (for example, M9155C)
– Product serial number (for example, MYXXXXXXXX). The serial number
label is located on the side panel of the module. The serial number can also
be viewed from the Soft Front Panel interface, but only after the software is
installed.
– Description of failure or service required
4Carefully pack the module in its original ESD bag and packing carton. If the
original carton is not available, use bubble wrap or packing peanuts and place
the module in a sealed container and mark the container as "FRAGILE".
5On the shipping label, write ATTENTION REPAIR DEPARTMENT and the RMA
number.
NOTE
Information on preventing damage to your Keysight equipment can be found at
www.keysight.com/find/tips.
NOTE
If any correspondence is required, refer to the product by serial number and
model number.

Getting Started 1
Keysight M9155/6/7C and M9161D Startup and Service Guide 19
Step 2: Verify M9155/6/7C and M9161D Shipment Contents
The following items are included with your M9155/6/7C and M9161D order:
– Keysight M9155/6/7C and M9161D Product Software and Information CD
(M9157-10001), which contains software, drivers, and printed product
documentation in the PDF format
– Keysight IO Libraries Suite CD (E2094-60003)
– Certificate of Calibration

1 Getting Started
20 Keysight M9155/6/7C and M9161D Startup and Service Guide
Step 3: Install the Software
System requirements
Prior to any installation or configuration, ensure that the following system
requirements are met:
Power up the host PC
Power up the host PC to install the M9155/6/7C and M9161D software.
Table 1-2 System requirements
Operating system Windows 7 (32-bit and 64-bit) Starter, Home Basic, Home Premium,
Professional, Ultimate, Enterprise
Processor speed
1 GHz 32-bit (x86),
1 GHz 64-bit (x64),
no support for Itanium 64
Available memory 1 GB minimum
Available hard-disk
space[a]
[a] Because of the installation procedure, less memory may be required for operation than is required for installation.
1.5 GB, includes:
– 1 GB for Microsoft .NET Framework 3.5 SP1[b]
– 100 MB for Keysight IO Libraries Suite[c]
[b] .NET Framework Runtime Components are installed by default with Windows Vista and Windows 7. Therefore, you
may not need this amount of available disk space.
[c] Version 16.0 (or later) of the Keysight IO Libraries Suite is required.
Video Support for DirectX 9 graphics with 128 MB graphics memory recommended
(Super VGA graphics supported)
Browser Microsoft Internet Explorer 7 or higher