KI RUCKUS TOTE STORAGE User manual

Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
below cover when an alternate
mounting location is desired, or
when no pre-drilled mounting
holes exist to install the Ruckus
Undersurface Rail Kit.
1. Determine the desired location to
mount the undersurface tote. A
two-part undersurface slide rail kit
must be installed to support the tote.
The slide rail pair must be mounted
square to the table edge and the
slide
rail
marked
pre-drilled
holes
Figure
1
cordless
power drill
tabletop
slide rail
slide rail
V-shaped
opening
#10 x /”
Phillips
screws
1
2
Figure
2
slide
rail
pilot
holes
tabletop
Assembly Instructions
Ruckus® Tote Storage
Undersurface Rail Kit
March 2020
front mounting holes for the slide
rails must be located 11/8” back from
the tabletop front edge. Mounting
holes of each slide rail must also be
positioned 14” apart (Figure 1).
2. Locate slide rails, then orient them
as shown, correctly positioned for
installation. The openings on the
slide rails must face each other and
the V-shaped openings must face
the front, “user side” of the tabletop
(Figure 1).
Important: Positioning the first slide
rail straight to the sides and/or square
to the table front edge is important.
Use a carpenter’s square, or a tape
measure to accurately measure from
the side of the tabletop to the side
of the slide rail’s mounting bracket
to assure that the slide rail aligns
straight before marking for drilling.
3. If holes are not pre-drilled on the
underside of the tabletop, skip to
step 4. If holes are pre-drilled on the
underside of the tabletop, position
one slide rail straight under the
tabletop, centering the mounting
slots over the pilot holes, then
secure using three #10 x 1/2” Phillips
screws. Take care to keep the slide
rail straight, and to not over-tighten
the screws, then proceed to step 12
on the next page (Figure 2).
4. Use a tape measure and pencil
to locate and mark the front pilot
hole location of the slide rail to the
underside of the tabletop. The marked
location must be 11/8” back from the
front, “user side” of the tabletop.
5. Carefully drill a 1/8” diameter, 1/2”
deep pilot hole under the tabletop
at the center of the marked location
using a power drill. Take care to not
drill too deep, piercing through the
tabletop (Figure 1).
6. Position one slide rail under the
tabletop. Center the slide rail’s front
mounting slot over the pilot hole,
then loosely secure using one
#10 x 1/2” Phillips screw.
7. Using the mounted slide rail as a
template, align the slide rail bracket
to be square to the “user side” edge
of the table by measuring, or by
using a carpenter’s square. Mark the
two remaining mounting slots clearly
on the underside of the tabletop.
8. Carefully drill a 1/8” diameter, 1/2”
deep pilot hole under the tabletop at
the center of each remaining marked
mounting slot location using a power
drill. Take care to not drill too deep,
piercing through the tabletop
(Figure 1).
9. Assure that the slide rail is square
to the front edge and secure using
two #10 x 1/2” Phillips screws. Take
care to keep the slide rail straight,
and to not over-tighten the screws
(Figure 2).
Tools Required
• Carpenter Square or Tape
Measure
• Cordless Power Drill
• 1/8” Drill Bit
Note: For some installations,
mounting holes may be pre-drilled
to the underside of the tabletop at the
factory. If so, go to and follow only
steps 2, 3, 12 & 13. The instructions

2
1330 Bellevue Street • P.O. Box 8100 • Green Bay, WI 54308-8100 • Tel [phone] • www.ki.com
© 2020 Krueger International, Inc. All Rights Reserved • Code KI-AI-000049R1/KI/PDF/0320
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
10. Orient the tote as illustrated and
insert the top, side rim of the
tote into the installed slide rail as
illustrated. While supporting the
tote up under the tabletop, slide the
second slide rail onto the opposite
side of the tote. Position the slide
rail tight to the side of the tote,
then mark the three mounting slots
to the bottom of the table for the
second, slide rail to be installed.
Make sure the front, “user side”
marked location is 11/8” back
from the front, “user side” of the
tabletop. Move the bracket away
and set aside (Figure 3).
Important: To allow for the tote to
slide more freely, drilling of pilot
holes for the second, slide rail must
be performed differently than the
first. Drilling of holes must be done
at the outside of the marked slots
under the tabletop, not in the center
of the slots.
11. Check that the first set and second
set of three marked mounting slots
are parallel to the first and are 14”
apart. Using a power drill, carefully
drill a 1/8” diameter, 1/2” deep pilot
hole under the tabletop at the
outside of each slot. Take care to
not drill too deep, piercing through
the tabletop (Figure 3).
12. Position the second slide rail
unit straight under the tabletop,
centering the mounting holes over
the pilot holes and secure using
three #10 x 1/2” Phillips screws.
Take care to not over-tighten
(Figure 4).
13. Insert the top side rims of the tote
into the installed pair of slide rails
and slide into place (Figure 5).
tote
Figure 5
slide rails
Figure
3
marked
pilot hole
tote
slide rail
tabletop
Figure
4
pilot
holes
slide
rail
#10 x /”
Phillips
screws
1
2
Ruckus®Tote Storage - Undersurface Rail Kit
Assembly Instructions
Part# 2.80713