Oracle ZS9-2 User manual

Oracle® ZFS Storage ZS9-2 Getting Started Guide
Contents
1 Oracle ZFS Storage ZS9-2 controller 2 Two power cords 3 Slide rail kit
4 Cable management arm 5 One 6-meter Ethernet cable (black) 6 Two 2.5-meter Ethernet cables (green, red)
7 Up to eight (mid-range model) or up to
sixteen (high-end model) 3-meter or 6-meter
active optical SAS cables (blue). Length and
quantity per customer order.
1

Front Panel Components
1 RFID tag 2 System status LED: Locator (white) 3 System status LED: Service Action
Required (amber)
4 System status LED: Power/OK (green) 5 Power button 6 Fan service action required (amber)
7 Power Supply (PS) service action required
(amber)
8 Over-temperature warning (amber) 9 Service Processor (SP) OK (green)
10 Do Not Service indicator 11 System disk 0 12 System disk 1
13 Filler panel 14 Filler panel 15 Filler panel
16 Filler panel 17 Filler panel 18 Filler panel
19 Filler panel 20 Filler panel 21 Filler panel
22 Filler panel
2

Back Panel Components
1 Power Supply Unit (PSU) 1 2 PSU 1 status indicators (top to bottom):
■ Attention (amber)
■ Power/OK (green)
3 PSU 0
4 PSU 0 status indicators (top to bottom):
■ Attention (amber)
■ Power/OK (green)
5 Second PCIe option (slot 1) 6 Third PCIe option (slot 2)
7 Fifth PCIe option (slot 3) 8 External SAS-3 HBA (slot 4) 9 Slot 5:
■ High-end model: External SAS-3 HBA
■ Mid-range model: Filler panel; slot not
available
10 Not available 11 Serial management (SER MGT) RJ-45
serial port
12 Service Processor (SP) NET MGT port
13 Network (NET) 100/1000BASE-T RJ-45
Gigabit Ethernet (GbE) port: NET 0
14 USB 3.0 port 15 System status LEDs:
■ Locate (white) - left
■ Attention (amber) - right, top
■ Power/OK (green) - right, bottom
16 Ethernet cluster interface card (slot 6) 17 First PCIe option (slot 7) 18 Slot 8:
■ High-end model: External SAS-3 HBA
■ Mid-range model: Filler panel; slot not
available
19 External SAS-3 HBA (slot 9) 20 Fourth PCIe option (slot 10)
Install the Hardware
For detailed information, see the Oracle ZFS Storage Appliance Installation Guide available from https://docs.
oracle.com/en/storage.
3

Connect System Cables
For detailed information, see the Oracle ZFS Storage Appliance Installation Guide available from https://docs.
oracle.com/en/storage. If you have clustered controllers, connect the cables to both controllers. Do not connect
power cables to the controllers or disk shelves until instructed to do so in "Power On and Configure the System."
The following illustration shows an Oracle ZFS Storage ZS9-2 high-end model.
Connect Clustered Controllers
If you have clustered controllers, connect the two controllers together. For detailed information, see the Oracle ZFS
Storage Appliance Cabling Guide available from https://docs.oracle.com/en/storage.
Connect Disk Shelves
The following illustration shows clustered controllers connected to an Oracle Storage Drive Enclosure DE3-24P (left
panel), and connected to four DE3-24x disk shelves (right panel). For additional configuration options, see Oracle
ZFS Storage Appliance Cabling Guide available from https://docs.oracle.com/en/storage. Do not connect
power cables to disk shelves or controllers until instructed to do so in "Power On and Configure the System."
Caution - Use active optical cables (AOCs) to connect Oracle ZFS Storage ZS9-2 external SAS-3 HBAs
to Oracle Storage Drive Enclosure DE3-24x disk shelves. Use copper cables to connect disk shelves to each
other, and to connect the controller to Oracle Storage Drive Enclosure DE2-24x disk shelves.
4

Caution - Attaching a SAS cable in the wrong orientation at the controller HBA or the disk shelf I/O Module
damages the port connector, and the system will not function properly.
The following procedure connects an AOC cable to the controller and to an Oracle Storage Drive Enclosure DE3-
24P disk shelf. For additional information, see Oracle ZFS Storage Appliance Cabling Guide available from https:
//docs.oracle.com/en/storage.
1. Facing the controller HBA, position the cable's release tab to the right (left panel) for the controller end, and to
the top for the disk shelf end (#1 in right panel).
2. Insert the cable connectors into the appropriate ports, aligning the cable connector latches (#2 in right panel)
with the port latch receiver holes (#3 in right panel). Ensure the latches engage with the receiver holes.
Power On and Configure the System
Required information: Network host name and port of your serial connection, or network management port DHCP-
assigned address. Connect disk shelf power cables, power on disk shelves, connect controller power cables, power
on controllers, and configure the system as described in the Oracle ZFS Storage Appliance Installation Guide
available from https://docs.oracle.com/en/storage.
Perform Initial Configuration
For detailed information, see the Oracle ZFS Storage Appliance Installation Guide available from https://docs.
oracle.com/en/storage, including properly configuring management interfaces and updating controller software.
5

Product Documentation Library
Documentation and resources for this product and related products are available in the storage section of the Oracle
Help Center, located at https://docs.oracle.com/en/storage/.
Documentation Accessibility
For information about Oracle's commitment to accessibility, visit the Oracle Accessibility Program web site at http:
//www.oracle.com/pls/topic/lookup?ctx=acc&id=docacc.
Access to Oracle Support
Oracle customers that have purchased support have access to electronic support through My Oracle Support. For
information, visit http://www.oracle.com/pls/topic/lookup?ctx=acc&id=info or visit http://www.oracle.
com/pls/topic/lookup?ctx=acc&id=trs if you are hearing impaired.
Feedback
Provide feedback on this document at http://www.oracle.com/goto/docfeedback.
Copyright © 2021, Oracle and/or its affiliates.
Copyright © 2021, Oracle et/ou ses affiliés.
Part No: F40862-01
August 2021
6