KICK ASS Jaxbox X1 User manual

USER MANUAL
X1
P OW E R S TAT I O N
VER 1.36
PATENT PENDING

SKU: KAJBABASE | V1.4
P OWE R S T A T I O N
OPTIONAL TRAY
OPTIONAL JUMPER CABLE
POWER STATION
888
ON
OFF
Why KickAss?
What makes KickAss different is
the fact that we offer the complete
solution: KickAss Power Station,
Solar Panels, Portable Fridges, AC
Chargers and everything you need
to get your off-grid camping needs
solved in one place.
Designed by the KickAss
Team
The KickAss Powerstation has
been designed in-house by the
KickAss Team and has taken over
3 years of hard work and
dedication to complete. We
listened to our customers over
many years to make a feature rich
and practical portable power
station.
Congratulations On Purchasing Your
New KickAss Jaxbox X1 Powerstation
IMPORTANT SAFETY INSTRUCTIONS
ŸFor charging 12V rechargeable batteries only.
ŸNever attempt to recharge non-rechargeable batteries.
ŸThe lid of the battery box must remain shut at all times whilst charging a battery or
powering a device from an outlet.
ŸDo not allow any metal objects to fall into the battery box or enter any of the ports.
ŸNever insert anything other than a compatible electrical plug into any of the ports on
the battery box.
ŸEnsure that the battery box is shut and the screws are tight before powering any
devices.
ŸDo not try to jumpstart when using lithium batteries.

OVERVIEW
SKU: KAJBABASE | V1.4
P OW E R S TA T I O N
888
CIGARETTE
SOCKET
2.4A USB &
QC3.0 USB
CIGARETTE
SOCKET
MAIN
ON/OFF
SWITCH
DIGITAL
VOLTMETER
VOLTAGE METER
ON/OFF SWITCH
DC-DC CHARGER
CARRY
HANDLE
CARRY
HANDLE
2.4A USB &
QC3.0 USB
BATTERY BOX
LID
BATTERY BOX
BASE
2X IN/OUT
POWER CONNECTORS
ALTERNATOR
INPUT
SOLAR
INPUT HIGH POWER
CONNECTOR
4X IN/OUT POWER
CONNECTORS
TIE DOWN
STRAP HOLE
FRONT
BACK SIDE
Material
ABS
Temperature Range
-10ºC to +60ºC
Plug and wires go up
and are hidden behind
a channel on the back
of the battery box.

GETTING STARTED
Step 1: Peel off the plastic film to expose
the non-slip surface of the silicone pads.
Step 2: Lower your battery into the battery
box base carefully, locating it as centrally
as possible on the non-slip pads.
12 VOLT - 120A/H
www.kickassproducts.com.au
AGM - DEEP CYCLE
VISIT OUR WEBSITE FOR MORE DETAILS
SKU: KAJBABASE | V1.4
P O W E R S TA T I O N
Step 3: Secure the battery in place by
tightening the velcro strap over the
battery.
Step 4: Install the battery cables onto the
terminal posts of the battery. Ensure the
red cable is connected to the positive (+)
terminal and both black cables connected
to the negative (-) terminal.
Tighten firmly but be sure not to over
tighten the battery terminals.
888
ON
OFF
- Do not Short Circuit
- Do not charge in a sealed container
- Keep sparks and flames away
- Do not leave battery in a discharged state
- Use only fully automatic or regulated chargers
- Discharging below 10.8 volts will void warranty
www.kickassproducts.com.au
CHARGE VOLTAGE FLOAT USE
CYCLE USE 14.4V - 15.0V (±3mV)
25A
MAXIMUM CURRENT
13.6 - 13.8V
(±3mV)
12 VOLT - 120A/H
AGM - DEEP CYCLE
NOTE: If your battery box base was
shipped with a battery installed, skip
to Step 3.
Note: the pads may be washed to
regain stickiness.

888
ON
OFF
SKU: KAJBABASE | V1.4
P O W E R S T A T I O N
Step 5: Tuck cables in under battery box
lid, lowering lid carefully onto box -
ensuring the lid is correctly oriented.
Step 6: Install the 4 provided screws to
fasten the lid to the base, being sure not
to over tighten with the supplied allen key.
SKU: KAJBABASE | V1.4
P O W E R S T A T I O N
888
ON
OFF
BATTERY TO USE
DEEP CYCLE
BATTERY
340mm 185mm
235mm
35kg
340mm L x 185mm W x 235mm H (with Silicone Mat)
35kg
AGM, Calcium, Wet, Gel or Lithium LiFePO4 (Deep Cycle Batteries)
Max. Battery Dimensions:
Max. Battery Weight:
Supported Chemistries:

SKU: KAJBABASE | V1.4
P OW E R S TAT I O N
888
ON
OFF
Step 1:
Confirm install location of tray, drilling any required
holes.
Install the strap under the tray, sliding the strap into
the slots either side.
Ensure strap is oriented correctly so that the hooks
face toward the Power Station when installed.
Securely affix the tray in position using bolts or
screws, whichever is applicable.
Ensure that washers are used when installing the
tray, to avoid damage.
Note: We do not provide the screws or bolts for this
installation.
Step 2: Ensure straps are laying outside
the tray before lowering the battery box
carefully onto the tray. Attach each strap
hook to the corresponding slot in the
Power Station.
Step 3: For ease of tightening, place
thumbs in each strap loop, pushing firmly
downwards. The strap should tighten and
hold the Power Station firmly in place.
To release, depress the buckle and pull
the strap to loosen.
MOUNTING TRAY (OPTIONAL)
TOP BOTTOM
OPTIONAL ACCESSORIES

ALTERNATOR INPUT
++
25A DC-DC & MPPT
SOLAR CHARGER
MASTER SWITCH VOLT METER ON/OFF
CIG SOCKET
10A MAX
CIG SOCKET
10A MAX
2 X USB
QC 3.0 & 2.1AMP
(5A OUT MAX)
2 X USB
QC 3.0 & 2.1AMP
(5A OUT MAX)
12.7 VOLT - 100%
12.2 VOLT - 50%
12.5 VOLT - 80%
10.5 VOLT - FLAT
HIGH POWER CONNECTOR
50A MAX
COMBINED
+
+ +
+ +
+ +
2X IN/OUT POWER CONNECTOR
4X IN/OUT POWER CONNECTOR
SOLAR LED STATUS
ALTERNATOR LED BATTERY STATUS WITH IGNITION WIRE CONNECTED
ALTERNATOR LED BATTERY STATUS
Alternator voltage 12V Alternator voltage 24V Alternator LED
Solar LED
Status
Alternator voltage 12V Alternator voltage 24V Alternator LED Status
Status
0-8.9 Volts
9-12.6 Volts
12.7-13.1 Volts
13.2 Volts
12-17.9 Volts
18-25.2 Volts
25.3-26.3 Volts
26.4 Volts
OFF
Flash 1 sec on 5 sec off
Flash 1 sec on 1 sec off
Solid on
Under operating voltage
Under cut-out voltage
Under cut-in voltage
Cut-in voltage reached, charging will
start after 30 second delay
0-8.9 Volts
9-11.6 Volts
11.7-12.1 Volts
12.2 Volts
12-17.9 Volts
18-23.2 Volts
23.3-24.3 Volts
24.4 Volts
OFF
Flash 1 sec on 5 sec off
Flash 1 sec on 1 sec off
Solid on
Under operating voltage
Under cut-out voltage
Under cut-in voltage
0-8.9 Volts
Unregulated 9-23V DC
OFF
Solid on
Under cut-in voltage
Cut-in voltage reached, charging will begin after 10 sec
delay (please note alternator has priority over solar)
DC-DC CHARGER GUIDE
X1 P O W E R S T A T I O N
Cut-in voltage reached, charging will
start after 30 second delay
LITHIUM, GEL, AGM, WET &
CALCIUM COMPATIBLE
iNTEGRATED WITH
CHARGER
HEAVY DUTY
CONSTRUCTION
PRE-WIRED FOR
PLUG & PLAY SETUP
BUILT-IN CIRCUIT
BREAKERS
multiple power
outlets
Automatic Starter
Battery Isolation
USB QC 3.0 QUICK
CHARGING
MPPT
WARNING!
SKU: KAJBALID-X1 | V1.83
SOLAR INPUT
(UNREGULATED 9-23V DC)
DO NOT SHORT CIRCUIT (UNFUSED)
JUMPSTART 600A 7S MAX
23V + Solar LED is Off
Stage 1 & 3 LED Fault Code Indication
Solar Input Voltage Exceeded
Non-Slip
Battery Pads
Solar voltage
REGISTERED DESIGN NO.: 202016277
PATENT PENDING
JUMPER CABLES (OPTIONAL)
KickAss 1000 Amp Jumper Cables have been designed to give you the optimum
starting power in the case of a flat starter battery. When it comes to Jumper Cables
there is no substitute for quality and these KickAss Jumper Cables have been designed
to be tough, durable and most of all, work flawlessly when you need them.
Note:
ŸDo not use jumper cables with lithium batteries.
ŸLeave the jumper cables connected to the flat battery for 5 minutes before
attempting to jump start battery.
CABLE LENGTH 2M
YOUR FLAT
BATTERY
SURGE PROTECTED
SWITCH/BUTTONS
The Master Switch
The master switch disconnects everything (except for the
large 175 amp Anderson style plug) from the battery including
the DC-DC Charger. Turning it off is a quick way to disconnect
all devices to ensure your battery is not being drained.
Note: The DC-DC Charger + Solar Regulator cannot charge
the internal battery while the Master Switch is in the OFF
position, nor can an external charger.
If another, external battery is connected through one of the
IN/OUT connectors, the DC-DC is able to charge that battery,
even with the Master Switch in the OFF position - bypassing
the internal battery.
The Voltmeter
The inbuilt voltmeter will display the voltage of your battery.
For an accurate voltage reading, disconnect all loads and
charging sources from the power station and test.
Note: The battery voltage table on the top sticker of the
battery box is to be used as a guide only, check your battery
specifications if you want to be precise.
.
12V DC
OFF ON

CONNECTIONS
2 X CIGARETTE
SOCKET OUTPUTS
2 x Cigarette Socket Outputs
= Maximum 10A output per socket
2 X DUAL USB / QC3.0
OUTPUTS
2 x Dual USB / QC3.0 Outputs
= 2 x 2.4A High Powered USB
(White)
= 2 x Quick Charge QC 3.0 Ultra
High Powered USB Outputs
(5V/3.1A, 9V/2A, 12V/1.5A - Blue)
OUTPUTS
4 x (50A) Anderson Style Plugs
on the side 2 x (50A) Anderson Style Plugs on the back
= Input / Output Capable.
= All Anderson Plugs combined must not exceed 50A total current.
WARNING:
1. Do not plug in multiple chargers as inputs.
2. Do not use an external charger while the DC-DC Charger is operating.
3. Exceeding 50A combined current rating will trigger the safety breaker. Safety breaker will
auto-reset in time.
6 X (50A) ANDERSON STYLE PLUGS
Benefits of Quick Charge
When paired with compatible devices, a Quick Charge-enabled charger delivers more power, allowing
the connected device to charge faster. As one of the most widely used of the fast charging technologies,
Quick Charge is already in many of your favorite smartphones. If your smartphone is Quick Charge 3.0-
compatible, you can charge up to 80% in just 35 minutes.
To future-proof your chargers, each new Quick Charge generation is backwards compatible, meaning it
will work with the generations that came before.
INPUTS/OUTPUTS

1 X (175A) ANDERSON STYLE PLUG
1 x (175A) Anderson Style Plug
on the left side
= High Current Inverter Output
= Emergency 600A Jump Starter Output (7 seconds)
= Connected directly to battery
WARNING:
1. Master switch does not disconnect the battery from
this connector.
2. This output is NOT Fused or Short Circuit
Protected.
3. Do not jump start a vehicle for longer than 7
seconds.
4. KickAss Deep Cycle batteries should be used for
jump starting in emergency situations ONLY, as it
will affect battery health.
5. Check battery specifications and compatibility with
high current draw before using jump start
connector.
6. Lithium batteries should not be used for jump
starting.
NOTE: THE 6 ANDERSON PLUGS INDICATED CANNOT
EXCEED A TOTAL OF 50 AMPS COMBINED.
MASTER SWITCH VOLT METER ON/OFF
12.7 VOLT - 100%
12.2 VOLT - 50%
12.5 VOLT - 80%
10.5 VOLT - FLAT
HIGH POWER CONNECTOR
50A MAX
COMBINED
+
+ +
+ +
+ +
2X IN/OUT POWER CONNECTOR
4X IN/OUT POWER CONNECTOR
SOLAR LED STATUS
ALTERNATOR LED BATTERY STATUS WITH IGNITION WIRE CONNECTED
ALTERNATOR LED BATTERY STATUS
Alternator LED Status
Alternator LED Status
Status
Flash 1 sec on 5 sec off
Flash 1 sec on 1 sec off
Under operating voltage
Under cut-out voltage
Under cut-in voltage
Cut-in voltage reached, charging will
start after 30 second delay
Flash 1 sec on 5 sec off
Flash 1 sec on 1 sec off
Under operating voltage
Under cut-out voltage
Under cut-in voltage
Under cut-in voltage
Cut-in voltage reached, charging will begin after 10 sec
delay (please note alternator has priority over solar)
DC-DC CHARGER GUIDE
X1 P O W E R S T AT I O N
Cut-in voltage reached, charging will
start after 30 second delay
LITHIUM, GEL, AGM, WET &
CALCIUM COMPATIBLE
iNTEGRATED WITH
CHARGER
HEAVY DUTY
CONSTRUCTION
PRE-WIRED FOR
PLUG & PLAY SETUP
BUILT-IN CIRCUIT
BREAKERS
multiple power
outlets
Automatic Starter
Battery Isolation
USB QC3 QUICK
CHARGING
MPPT
WARNING!
DO NOT SHORT CIRCUIT (UNFUSED)
JUMPSTART 600A 7S MAX
Solar Input Voltage Exceeded
Non-Slip
Battery Pads

ALTERNATOR
MPPT SOLAR
1 X TRIPLE ANDERSON STYLE PLUG
1 X (50A) ANDERSON STYLE PLUG
1 X (50A) Anderson Style Plug
(for Solar Input)
1 X Triple Anderson Style Plug
= 9-32V DC Starter Battery Input (+/-)
= Ignition source connection
= Minimum Solar Input Voltage: 9V DC
= Maximum Solar Input Voltage: 23V DC
= Maximum Solar Input Current: 25A
Unregulated Solar Input - utilises in built DC-DC MPPT regulator.
Not suitable for regulated solar input, connect to a standard in/out connector when
using an external or panel-mounted solar controller/regulator.
WARNING:
1. Do not exceed the Maximum Voltage of 23V DC
2. Do not exceed the Maximum Input Current of 25A
INPUTS