Kid Eco Toy Fort User manual

Toy Fort Assembly Instructions
(Registered Design 4002675) Please retain this document for future reference.
www.cardboardtoys.com
Please fold all creases well prior to assembly of toy and ensure all parts are securely connected.
The toy fort is designed primarily for indoor use but is also suitable for outdoor use in dry, calm conditions. The toy fort should be stored in a dry
place and should be kept away from fire or any naked flame. The toy fort should be inspected regularly before, during and after use for any signs
of damage, which could cause potential injury.
WARNING : This product should be kept out of the reach of very young children and only be used under the direct supervision of an adult.
3WM Ltd T/A Kid-Eco
Units 1,2 & 4, Hollis Road, Grantham, Lincs. NG31 7QH
tel: [phone] | fax: [phone] | email: [e-mail]
Toys that won’t cost us the earth
Assembled Toy fort
page 1 of 3

Toy Fort Assembly Instructions
(Registered Design 4002675) Please retain this document for future reference.
www.cardboardtoys.com
Please fold all creases well prior to assembly of toy and ensure all parts are securely connected.
The toy fort is designed primarily for indoor use but is also suitable for outdoor use in dry, calm conditions. The toy fort should be stored in a dry
place and should be kept away from fire or any naked flame. The toy fort should be inspected regularly before, during and after use for any signs
of damage, which could cause potential injury.
WARNING : This product should be kept out of the reach of very young children and only be used under the direct supervision of an adult.
3WM Ltd T/A Kid-Eco
Units 1,2 & 4, Hollis Road, Grantham, Lincs. NG31 7QH
tel: [phone] | fax: [phone] | email: [e-mail]
page 2 of 3
Toys that won’t cost us the earth
Step 1
Step 2
Step 3
•Insert tabs (A1) into slots (B1) at opposite end of turret base and gently pull down to lock into place.
•Fold flaps (C1) inwards for stability.
•Insert tab (A2) into slot (B2) at opposite end of turret top and gently pull down to lock into place.
•Fold flaps (C2) under, ensuring corner tabs are on the inside.
•Align the larger slots in the turret top with the larger tabs on the turret base and the smaller slots
with the smaller tabs.
•Gently push down until turret top is firmly attached to base. The turret is now complete.
•Repeat for all 4 turrets.
A1B1
A1
A2
C1
C2
B1
B2
Assembled
Turret
Turret Base
(4 off)
Turret Top
(4 off)

Toy Fort Assembly Instructions
(Registered Design 4002675) Please retain this document for future reference.
www.cardboardtoys.com
Please fold all creases well prior to assembly of toy and ensure all parts are securely connected.
The toy fort is designed primarily for indoor use but is also suitable for outdoor use in dry, calm conditions. The toy fort should be stored in a dry
place and should be kept away from fire or any naked flame. The toy fort should be inspected regularly before, during and after use for any signs
of damage, which could cause potential injury.
WARNING : This product should be kept out of the reach of very young children and only be used under the direct supervision of an adult.
3WM Ltd T/A Kid-Eco
Units 1,2 & 4, Hollis Road, Grantham, Lincs. NG31 7QH
tel: [phone] | fax: [phone] | email: [e-mail]
page 3 of 3
Toys that won’t cost us the earth
Step 4
Step 5
•Fold flaps (C1) inwards for stability.
•Insert tabs (A1 & B1) on toy fort wall into adjacent slots on assembled turret and gently pull down to lock into place.
•Bend smaller flaps on tabs (B1) up to lock toy fort wall into place. Repeat for opposite side.
•Repeat operations for all 4 walls.
A1
B1
A1
B1
C1 C1 Wall Section (4 off)
Assembled Wall