kim lighting Hubbell EL210 User manual

EL220
Accent Lights Installation Instructions
P.O. Box 60080 • 16555 East Gale Ave.
City of Industry, California 91716-0080
626/968-5666 •FAX [phone]
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
IMPORTANT SAFETY INSTRUCTIONS!
WARNING: Fixtures must be grounded in accordance with local codes or the National Electrical
Code. Portable spear or surface mounts using a cord and plug must be plugged into a receptacle
protected by a Ground Fault Circuit Interrupter (GFCI) in accordance with the National Electrical Code.
Failure to take these steps may result in serious personal injury.
CAUTION: Lighted lamp is HOT! Do not touch hot lens, guard or enclosure. Fixtures are approved for
above grade installation only.
MAINTENANCE: To maintain light efficiency and prevent fixture overheating, lenses must be kept clean
and free of dirt, dust, leaves, trash and mineral deposits from water. For optimum performance a regularly
scheduled maintenance program should be followed. KEEP THIS SHEET FOR FUTURE REFERENCE.
Revised 7/16/10 ECN 100715008 Status 13 Part No. 95440
Your KIM fixture(s) is supplied with K” NPSM male mounting threads and locknut.
Tools Required:Thread SealantFlat Blade ScrewdriverPhillips Screwdriver
Adjustable WrenchB"Allen Wrench
Installation Instructions: Make certain the electrical supply is OFFbefore starting installation instructions.
1. Coat threads with sealant to keep
moisture from entering J-Box.
2. Tighten coupling onto mounting
device. (Consult KIM Landscape
Catalog for mounting device
options.)
4. Loosen screw, adjust fixture angle,
and tighten screw.
EL210
3. Install fixture onto coupling. Attach
fixture leads observing polarity,
i.e.; green-to-ground, white-to-
common, and black-to-voltage.
5. Loosen setscrew, adjust fixture
rotation, and tighten setscrew.
!
6. Push lamp gasket onto lamp.
Caution: Do not press gasket
too far onto lamp or seal with
socket will be lost. (See gasket
illustration on page 2.)
Lamp Gasket
!

Page 2 KIM Lighting • 16555 E. Gale Ave. • P.O. Box 60080 • City of Industry, CA 91716-0080 • 626/968-5666 Fax [phone]
Accent Lights EL210 & EL220 Installation Instructions
LA6 (EL220 Only)
Optional Lens / Lens Clip
HS220 (EL220 Only) Optional Half Shield
Tool Required: ❑ B” Hex Wrench
1. Slip shield over end of fixture.
2. Adjust shield to desired orientation, and tighten
screw to secure.
1. Slip lens into fixture, convex side out.
2. While pinching ends of lens clip together, place
clip into fixture end (on top of lens). Release
ends to secure lens.
KIM LIGHTING LIMITED WARRANTY
When installed in accordance with Kim Installation Instructions and
accepted trade practices, the following shall apply:
General Product Limited Warranty Coverage
All material and component parts used in the manufacture of Kim
Products, are warranted to be free from defects of material and/or
workmanship for a period of 1 year from date of sale, with the
following exceptions:
Auxiliary Equipment
All auxiliary equipment (such as lamps, ballasts, and transformers)
provided by and/or included in Kim Products shall carry the
component manufacturer's warranty.
Copper and Bronze Landscape Components
Copper and Bronze Landscape fixture components shall be
warranted against defects of material and/or workmanship, and
failure due to corrosion, for a period of 25 years from date of sale.
Composite In-Grade Components
Composite In-Grade fixture components installed below grade,
shall be warranted against defects of material and/or workmanship,
and failure due to corrosion, for a period of 7 years from date of
sale.
Aluminum Landscape Components
Aluminum Landscape fixture components not in direct contact with
soil, shall be warranted against defects of material and/or
workmanship for a period of 3 years from date of sale. Aluminum
fixture components in direct contact with soil shall be warranted
from defects of material and failure from corrosion for a period of 1
year from date of sale.
Limit of Liability and General Conditions
Only products which are installed, used and maintained in
accordance with applicable Kim instructions, specifications and
accepted trade practices, are covered by the Kim Warranty.
During the warranty period, with proof of purchase, Kim will repair
or replace with the same or similar product, at Kim's option, without
charge. Labor costs are the owner's responsibility and are
excluded from this warranty. This warranty is void if the product is
modified, tampered with, misapplied, poorly installed, improperly
maintained, or subjected to abnormal conditions.
Repair or replacement as provided under this warranty is the
exclusive remedy of the purchaser. This warranty is in lieu of all
other warranties, expressed or implied, including any implied
warranty of fitness for a particular application. Kim Lighting shall
not be liable to the purchaser for indirect or consequential
damages.
How may we serve you better?
Please let us know. Visit our website at:
www.kimlighting.com
Your input matters to us.
Correct
Installation
Incorrect
Installation
Lamp Gasket
IMPORTANT
Gasket Illustration
LAMP INFORMATION
Cat. No. Lamp Type Max. Watts
EL210 PAR 38 Only
EL220 PAR 38 or R40*
150
Incandescent
or Halogen
* Important: If the R40 lamp is used with the
EL220 (only) aimed up, LA6 lens is required to
prevent lamp breakage by thermal shock from
water. Do not aim R40 lamp down unless
protected from direct water spray.