kincrome K15057 User manual

1
STEEL FABRICATED OFFSET VICE
Steel Fabricated
Offset Vice
K15057, K15058, K15059
ED1/SEPT 19
INDUSTRIAL
AND
WORKSHOP
QUALITY
STEEL
FABRICATED
KINCROME
UNBREAKABLE
GUARANTEE

2
STEEL FABRICATED OFFSET VICE
Table of Contents
Know Your Product .................................... 2
General Safety Instructions ...................... 3
Additional Safety Instructions................... 3
Operation.................................................... 3
Maintenance & Warranty .......................... 4
4
51
3
2
Know your product
1. Spindle Handle
2. Spindle
3. Replaceable Jaws
4. Spindle Nut
5. Mounting Holes
Specifications
Specifications
Jaw Width
Jaw Opening
Throat Depth
Offset
Weight
Specifications
Jaw Width
Jaw Opening
Throat Depth
Offset
Weight
Specifications
Jaw Width
Jaw Opening
Throat Depth
Offset
Weight
K15057
102mm 152mm 202mm
102mm 152mm 202mm
95mm 105mm 140mm
Right Right Right
11.8kg 23.34kg 41.5kg
K15058 K15059

3
STEEL FABRICATED OFFSET VICE
General Safety Warnings
Save all warnings and instructions for future reference.
WARNING! Misuse of vice can cause serious injury. Please read, understand and follow all instructions outlined in
this manual before setting up the vice.
a.) To ensure safety, vice must be installed and used properly.
b.) ALWAYS make sure the workbench top is secure.
c.) ALWAYS use eye, face, and ear protection.
d.) ALWAYS keep moving parts lubricated with multipurpose grease.
e.) ALWAYS keep workpiece centered in jaws. Uneven clamping pressure across jaws could damage vice.
f.) DO NOT overtighten jaws or lockdowns, damage to vice or workpiece could result. TIGHTEN BY HAND ONLY.
g.) DO NOT unscrew jaw beyond maximum opening.
h.) DO NOT place pressurised containers in vice.
i.) DO NOT use extreme heat or prolonged heat on vice.
j.) DO NOT strike any part of vice; permanent damage could result.
k.) DO NOT expose the vice to rain or wet conditions.
l.) This product is not a toy. Keep it out of reach of children.
m.) The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions
and situations that may occur. It must be understood by the operator that common sense and caution are factors which
cannot be built into this product, but must be supplied by the operator.
Assembly
The only assembly required for the Kincrome Steel Fabricated Vices is the assembly of the handle.
1. Unscrew one of the end caps located on the spindle handle.
2. Slide the spindle handle through the handle assembly.
3. Reinstall the end cap removed earlier.
Mounting Tips
1. Use proper sized bolts, nuts, locks and flat washers in all base mounting holes. Never weld the base of the
vice to any metal object.
2. Only hand tighten the swivel base lock down nuts at the side of the vice.
3. Never use a pipe extension to tighten the lock handles. This can cause the handles to bend and stress
the lock down bolts.
4. Make sure the vice is mounted to a properly secured bench top, capable of supporting combined weight of vice,
intended work pieces and applicable forces.
Tips Using The Vice
1. Always use the necessary vice needed for the size and capacity of the workpiece.
2. Never use a hammer, pipe extension or cheater bar on spindle handle of the vice.
3. Never unscrew the movable jaw beyond the maximum specified opening of the vice.
4. Never use a vice as a press for assembly or disassembly of objects.
WARNING! Always wear eye and face protection when striking objects held by the vice or when using power tools

4
STEEL FABRICATED OFFSET VICE
Maintenance
1. Before each use, inspect the general condition of the vice. Check for misalignment or binding of moving parts, cracked
or broken parts and any other condition which may effect safe operation.
2. Keep machined surfaces and all moving parts clean and free of dirt, chips, and foreign materials.
3. Use multipurpose grease to keep moving parts lubricated.
4. Routinely apply mineral oil to machined surfaces to prevent surface rust.
Office Contact Details
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.kincrome.com.au
Caring For The Environment
When a tool is no longer usable it should not be disposed of with household waste, but in an environmentally friendly
way. Please recycle where facilities exist. Check with your local council authority for recycling advice.
Recycling packaging reduces the need for landfill and raw materials. Reuse of recycled material decreases pollution
in the environment. Please recycle packaging where facilities exist. Check with your local council authority
for recycling advice.
Notes:
Warranty
Warranty given by Kincrome Tools & Equipment Pty Ltd of 3 Lakeview Drive, Caribbean Park, Scoresby, Victoria, Australia (Tel +61
3 9730 7100) If this product has materials or workmanship defects (other than defects caused by abnormal or non warranted use)
you can, at your cost, send the product to place of purchase, an authorised Kincrome service agent or one of Kincromes addresses
for repair or replacement. Your rights under this warranty are in addition to any other rights you have under the Australian, United
Kingdom & Ireland Consumer Law or other applicable laws. Our goods come with
guarantees that cannot be excluded under the Australian, United Kingdom & Ireland Consumer Law. You are entitled to a replace-
ment or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
For further details please visit www.kincrome.com.au or call us. Due to minor changes in design or manufacture, the product you
purchase may sometimes differ from the one shown on the packaging.