Kinesis Gaming KB975 Series User manual

1
KB975
User Manual
RGB Split Programmable Mechanical

2
Keyboard models covered by this manual:
 KB975-BLU
 KB975-RED
 KB975-BRN
October 2, 2018 Edition
This manual covers features included through firmware version 1.0.0. To download the latest firmware
and to access all support resources visit www.KinesisGaming.com/Support.
To shop for accessories visit KinesisGaming.com/Accessories:
 Lift Kit- Adjustable tenting accessory (5°/10°/15°) for use with Palm Supports
 V3 Pro- Adjustable tenting accessory (5°/10°/15°) for use without Palm Supports
 Palm Pads- Cushioned palm pads for use with Palm Supports
 XL Mouse Pad- Oversized Desk Mat/Mousepad designed for use with the Freestyle Edge
 Vektor– RGB Gaming Mouse (Dual-Zone Lighting, 6 Programmable Buttons)
© 2018 by Kinesis Corporation, all rights reserved. Kinesis and Freestyle are registered trademarks of Kinesis
Corporation. Freestyle Edge, SmartSet, and v-Drive are trademarks of Kinesis Corporation. All other
trademarks are property of their respective owners.
Information in this document is subject to change without notice. No part of this document may be reproduced
or transmitted in any form or by any means, electronic or mechanical, for any commercial purpose, without the
express written permission of Kinesis Corporation.
Kinesis Corporation
22030 20th Avenue SE, Suite 102
Bothell, Washington 98021 USA
www.KinesisGaming.com
FCC Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
 Reorient or relocate the receiving antenna
 Increase the separation between the equipment and receiver
 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
 Consult the dealer or an experienced radio/TV technician for help
Warning
To assure continued FCC compliance, the user must use only shielded interfacing cables when connecting to computer or peripheral. Also, any unauthorized changes or
modifications to this equipment would void the user’s authority to operate.
INDUSTRY CANADA COMPLIANCE STATEMENT
This Class B digital apparatus meets all requirements of the Canadian Interface-causing Equipment Regulations.
Cet Appareil numerique de la classe B respecte toutes les exiginces du Reglement sur le material broilleur du Canada.

3
Table of Contents
1.0 Read Me First………………………………………………………………………………………………………………………. 4
2.0 Keyboard Overview………………………………………………………………………………………………………………... 4
3.0 Introduction…………………………………………………………………………………………………………………………. 6
3.1 Backlighting…...……..…………………………………………………………………………………………………….. 6
3.2 Dual Layer Layouts (Embedded Fn Layer)……………………………………………………………………………… 6
3.3 Multimedia Actions…………………………………………………………………………………………………………. 6
3.4 Programming Cluster………………………………………………………………………………………………………. 6
3.5 Removable Palm Supports……………………………………………………………………………………………….. 6
3.6 SmartSet Programming Engine- Onboard Shortcuts………………………………………………………………….. 7
3.7 Adjustable Linking Cable………………………………………………………………………………………………….. 7
3.8 Game Bank…………………………………………………………………………………………………………………. 7
4.0 SmartSet Onboard Programming………………………………………………………………………………………………. 7
4.1 Layouts……………………………………………………………………………………………………………………… 7
4.2 Recording Macros…………………………………………………………………………………………………………. 8
4.3 Remapping Keys…………………………………………………………………………………………………………… 8
4.4 Run Status Report…………………………………………………………………………………………………………. 9
4.5 Open/Close v-Drive………………………………………………………………………………………………………. 9
4.6 Adjust Global Macro Speed………………………………………………………………………………………………. 10
4.7 NKRO Mode………………………………………………………………………………………………………………… 10
4.8 Game Mode………………………………………………………………………………………………………………… 10
4.9 Soft Reset………….……………………………..…………………………………………………………………………. 10
4.10 Hard Reset……………………………..…………………………………………………………………………………... 11
4.11 Refresh Settings…………………………………………………………………………………………………………… 11
4.12 Program Lock………………………………………………………………………………………………………………. 11
4.13 Update Firmware………………………………………………………………………………………………………….. 11
4.14 Adjust Status Report Playback Speed…………………………………………………………………………………… 11
4.15 Force v-Drive Open………………………………………………………………………………………………………… 11
4.16 Select Lighting Profile……………………………………………………………………………………………………... 11
5.0 SmartSet Programming App (Windows)………………………………………………………………………………………. 12
6.0 Direct Programming (Mac, Linux, & Chrome)………………………………………………………………………………... 17
6.1 Programming Layouts…………………………………………………………………………………………………….. 17
6.2 Position Token Map……………………………………………………………………………………………………….. 18
6.3 Key Action Token Dictionary……………………………………………………………………………………………… 19
6.4 Direct Programming Remaps……………………………………………………………………………………………. 20
6.5 Direct Programming Macros……………………………………………………………………………………………… 20
6.6 Programming Global Keyboard Settings………………………………………………………………………………... 21
6.8 v-Drive Repair………………………………………………………………………………………………………………. 22
7.0 Maintenance………………………………………………………………………………………………………………………… 23
8.0 Technical Support, Repairs, and Returns…………………………………………………………………………………….. 23
9.0 Warranty & Limitation of Liability……………………………………………………………………………………………….. 23
5.1 12
Installing the SmartSet App……………………………………………………………………………………………………………………………
5.2 Using the SmartSet App………………………………………………………………………………………………………………………………… 13
5.5 Lighng Editor……………………………………………………………………………………………………………………………………………….. 16
5.3 Layout Editor…………………………………………………………………………………………………………………………………………………. 13
5.4 Global Keyboard Sengs Editor……………………………………………………………………………………………………………………… 15
6.7 Direct Programming Lighting……………………………………………………………………………………………... 21

4
1.0 Read Me First
Health and Safety Warning
Continuous use of any keyboard may cause aches, pains or more serious cumulative trauma disorders such
as tendinitis and carpal tunnel syndrome, or other repetitive strain disorders.
 Exercise good judgement in placing reasonable limits on your keyboarding time every day.
 Follow established guidelines for computer and workstation setup.
 Maintain a relaxed keying posture and use a light touch to press the keys.
Keyboard is not a medical treatment
This keyboard is not a substitute for appropriate medical treatment! If any information in this guide appears to
contradict your health care professional’s advice, please follow your health care professional’s advice.
No warranty of injury prevention or cure
Kinesis bases its product designs on research, proven features and user evaluations. However, because of
the complex set of factors believed to contribute to computer-related injuries, the company can make no
warranty that its products will prevent or cure any physical ailment. Your particular risk of injury may be
affected by workstation and chair design, posture, time worked without breaks, type of work, activities outside
the workplace, and/or individual physiology.
Quick Start Guide
If you are eager to get started, please consult the included Quick Start Guide. The Quick Start Guide can also
be downloaded from KinesisGaming.com/Support. Consult this full User Manual for detailed descriptions of
both basic and advanced features.
Read This User’s Manual
Even if you don’t normally read manuals or you are a long-time user of Kinesis keyboards, we strongly
encourage you to review this entire manual. The Freestyle Edge is a fully-programmable keyboard with
powerful tools and features. If you unknowingly execute a programming shortcut or key combination, you
could inadvertently alter the layout of your keyboard which might necessitate a Hard Reset of the keyboard.
If you have no plans to re-program the keyboard and would like to disable all programming features see
Section XX.

5
2.0 Keyboard Overview
Specifications
 Compact tenkeyless design with standard US ANSI key layout
 6’ USB cable and 20” adjustable linking cable
 2 year limited warranty
 Dimensions: 1.25” tall x 15.5” wide x 10.25” deep (Without Palm Supports: 7.25” deep)
 Weight: 2.8 lbs
Features
 Premium Cherry® MX mechanical switches
 16.8M Color RGB LED backlighting with 9 customizable lighting profiles and 7 unique lighting effects.
 SmartSet Programming Engine with on-the-fly remaps and macros, and Windows Programming App
 9 dual-layer, fully-programmable layouts
 4MB onboard memory (the v-Drive™)
 Multimedia actions in the embedded Fn layer
 Game Bank with 9 programmable game keys for binding macros and custom key actions
 Available Game Mode & NKRO Mode
 1000mz polling
 100% anti-ghosting
Package Contents
 Freestyle Edge mechanical keyboard, 20” adjustable linking cable, and detachable Palm Supports
 Quick Start Guide
System Requirements
 Keyboard: Windows® 7-10, MacOS® X v10.6+, Chrome OS® or Linux® & full-size USB Port
 SmartSet Programming App (Required for customization of Lighting Profiles): Windows 7-10, Internet
Connection (download only), 25MB available hard-disk space
Keyboard Setup
To setup the Freestyle Edge simply plug the USB cable into a full-size USB port on your computer. The Edge
does not require the installation of any special software or drivers or an internet connection. To access the
SmartSet App, visit the URL below and download the SmartSet App to your Windows PC.
KinesisGaming.com/fs-edge-rgb-support

6
3.0 Introduction
3.1 Backlighting
The Freestyle Edge is equipped with vibrant RGB backlighting. Tap the LED key to quickly toggle the
backlighting On and Off
To choose from one of the 9 pre-configured Lighting Profiles, simply hold the SmartSet Key and tap the LED
key, then select a number 1-9 from the number row. Alternatively, choose the number 0 to disable
backlighting or the letter “P” to enable Pitch Black mode. Tap the SmartSet Key to finalize your selection and
resume normal keyboard function.
Each of the 9 Lighting Profiles can be customized using the SmartSet App (See Section XXX).
3.2 Dual Layer Layouts (Embedded Fn Layer)
The Freestyle Edge RGB has two separate layers so each of the 95 full-size keys can be programmed to
perform two unique actions per layout– a top layer action and an “embedded” Fn layer action. Tap the Fn key
to toggle between the top layer and the Fn layer. The Fn indicator light will illuminate while the Fn layer is
active. The default Fn layer actions mirror the top layer except for 8 keys which have unique embedded
actions: the F1-F6 keys (multimedia actions) and the Pause key (Insert) and the Delete Key (Scroll Lock).
3.3 Multimedia Actions
Change your audio on the fly by accessing the 6 standard multimedia actions by using the Fn key to toggle on
the Fn layer. These multimedia actions can be reassigned to any key on the keyboard in either layer using
onboard programming (see Section XX) or the SmartSet App (see Section XX).
3.4 Programming Cluster
The four Programming Cluster keys enable quick and easy onboard reprogramming (see Section XX). The
Layout key toggles between the 3 primary layouts (1, 2, and 3), the Macro key controls on-the-fly macro
recording, and the Remap key controls onboard remapping (aka rebinding). The 4th key with the gear icon is
the SmartSet Key, and it controls all onboard programming shortcuts.
3.5 Removable Palm Supports
The Edge’s palm supports are detachable so you can customize the keyboard based on your typing and
gaming preferences. To remove the supports, flip the keyboard over and gently wiggle the palm support to lift
the tabs over the bumps on the underside of the keyboard, and then pull straight out. To reattach, slide the
palm support into the key modules until they latch into place. Note: if the palm support doesn’t snap into place
easily you may be trying to attach it to the wrong key module, or it may be misaligned.
Profile 1 Profile 2 Profile 3 Profile 4 Profile 5 Profile 6 Profile 7 Profile 8 Profile 9
RGB Wave
(Right)
RGB Wave
(Down)
RGB
Spectrum
Reacve
(Green)
Individual Monochrome
(Blue)
Monochrome
(Red)
Monochrome
(Green)
Breathe
(White)
e
t

7
3.6 SmartSet Programming Engine- Onboard Shortcuts
The SmartSet key is used in conjunction with the F7-F12 keys to activate onboard shortcuts. Onboard
shortcuts are legended with the SmartSet icon to differentiate them from embedded Fn layer actions.
Additional (unlegended) onboard shortcuts are described in Section XX.
To trigger an onboard shortcut, hold the SmartSet Key and then tap F7-F11. To prevent against accidentally
triggering the Soft Reset shortcut, you must also hold the Shift key along with the SmartSet Key before
tapping F12. For a detailed explanation of onboard shortcuts see Section XX .
3.7 Adjustable Linking Cable
Adjusting Length: The two key modules are connected by a 20” braided linking cable that can be
adjusted to suit your typing preferences and gaming style. The basic configuration allows for up to 12” of
separation. If you need additional cable, simply remove the cable compartment cover on the back of the left
key module and thread out more of the stored cable. Once you have achieved the desired cable length,
carefully fit the excess cable into the compartment removing any kinks and slide the cable cover on until it
latches. Note: For best results rotate the left key module to remove any kinks from the cable so it lies flat.
Positioning: Position the key modules in the optimal configuration relative to your other input
devices, or separate the modules to shoulder-width for maximum typing comfort. There is no wrong way to
configure the Edge, experiment with different positions to find the configurations that work best for you.
3.8 Game Bank
The Game Bank comprises nine fully programmable keys (blank by default) that can be
programmed to perform any custom key action or macro, in either layer. The Game Bank is
perfect for moving critical right-sided keys over to the left key module to enable one-handed play,
storing macros, or moving the multimedia actions to the top-layer.
4.0 SmartSet Programming Engine
The SmartSet Programming Engine allows you to custom program your Freestyle Edge keyboard without
installing any software or special drivers on the computer. Custom layouts and settings are saved directly to
the keyboard’s v-Drive so they move with the keyboard when you take your game on the road. There are
three ways to program your Freestyle Edge: 1) Onboard Programming (all O/S), 2) the SmartSet
Programming App (Windows), and Direct Programming (all O/S).
Onboard Programming: Unlike most programmable keyboards, the Freestyle Edge can be completely
customized without launching any software. Onboard programming is a quick and convenient way to
customize layouts, toggle lighting profiles, and adjust keyboard settings with simple-to-use onboard shortcuts.
4.1 Layouts (Layout or SmartSet + Number Row)
The Freestyle Edge puts 9 fully-programmable, dual-layer layouts at your disposal. Each layout can be
custom configured for different games or users. The LEDs above the Layout Key indicate the active layout.
Tap the Layout Key to toggle through the three primary layouts. To jump directly to any of the nine
layouts, hold the SmartSet Key and then tap 1-9 in the number row to select the desired layout .

8
4.2 Recording Macros
A macro is string of characters or key actions that is triggered by a single key press. Macros are powerful
tools that allow you to quickly produce multiple in-game actions in rapid succession. Macros are assigned to
the active layout at the time of recording and each layout can store up to 7200 total macro characters. Each
macro can be up 300 characters long so you can store 24 max length macros (24 x 300 = 7200) in each
layout, or many more shorter macros.
To record a macro on-the-fly, tap the Macro key in the Programming Cluster to enter Macro Record
Mode, choose your trigger key(s) and then type out your macro. Tap the Macro key stop recording.
Macro Trigger Key(s): After entering Macro Record Mode, the Macro LED will flash rapidly prompting
you to select a trigger key. Any full-size non-modifier key can be used as a macro trigger. A macro can also
be triggered by a two-key combination by pairing the primary trigger key with a modifier-key “co-trigger”. To
assign a key combination as a macro trigger, first press and hold one of the six standard modifier keys (Ctrl,
Alt or Shift) and then tap the desired primary trigger key. Note: The Windows key is not recommended for use
as a macro co-trigger.
Macro Contents: After a valid macro trigger has been selected, the Macro LED will flash slowly
prompting you to begin recording your macro (open an appropriate program during recording). Every single
keystroke will be recorded so if you make a mistake, we recommend restarting rather than using backspace
key. To stop recording and save your macro, simply tap the Macro key. Note: Macro Record Mode will end
automatically when you hit the max length of 300 keystrokes.
Only Keystrokes Recorded: The speed at which you type out the macro and pauses between strokes
are not recorded. The macro will playback at the Global speed setting (see Section XX) by default, but the
playback can be customized by adding internal timing delays (1-999ms or random delays) or by setting a
custom playback speed for that specific macro using the SmartSet App (see Section XX) or Direct
Programming (see Section XX).
Macro Playback: To playback a macro, simply press the trigger key(s). Modifier co-triggers should be
pressed first and held while the primary trigger key is then tapped. See Sections XX and XX to adjust the
playback speed.
Erasing a Macro: To erase a macro without launching the SmartSet App, simply tap the Macro key,
then input the trigger key(s) of the macro you wish to erase. Once the Macro LED starts flashing slow, simply
tap the Macro key again.
Macro Limit: Each layout can accommodate 7200 macros characters spread across any number of
macros. When you have reached the limit for a given layout, the keyboard will flash if you attempt to record
another macro key to signal that you must first erase a macro before recording a new one.
4.3 Remapping Keys
With the Remap key, you can reassign any default key action on the Freestyle Edge to any other full-size key
(in either layer) to customize the layout for gaming or typing. Note: The Fn key can only be remapped via the
SmartSet App or Direct Programming.
Tap the Remap key to enter Remap Mode. The Remap LED will flash rapidly to prompt you to first select
the “Source” key action (i.e., the key action that you wish to assign). After selecting the Source key, the
LED will flash slowly prompting you to select the “Destination” key position (i.e., the physical key).

9
Remapping Tips
 Remapping is a one-way process, it creates a duplicate key action but it does not “swap” two key actions.
To “swap” two keys you must perform two separate remap programming commands.
 Remapping only operates on one layer at a time. To remap the same key in both layers you must perform
two separate remap commands, one for each layer.
 While Remap Mode is active, you can use the Fn key to navigate between layers as necessary if you wish
to move a key action (e.g., the media keys) from the Fn layer to the top layer, or vice versa.
 While Remap Mode is active, the keyboard reverts back to the default QWERTY layout so you can never
“lose” a key.
Special Actions: The Freestyle Edge supports a number of special actions that are not found in the
default keyboard layout. These actions can be assigned using the SmartSet App or Direct Programming (see
Sections XX and XX).
Macro and Remap conflict: If you assign a macro to a remapped key, macro playback will take priority
over the remap action, except when macros have been temporarily disabled (see Section XX).
4.4 Run Status Report (SmartSet + F7)
Use the Status Report to “print-to-screen” a convenient report of the current global keyboard settings.
Make sure you have a text editing program (e.g., Notepad, Word) selected as the
active window before running a Status Report.
 Layout> Active layout loaded to the keyboard (1-9)
 Remaps> Number of remapped keys in the active layout
 Macros> Number of macros saved to the active layout
 Macro Speed> “Global” macro playback speed (see Section XX)
 Status Report Speed> Speed at which the Status Report is played
 LED> Active lighting profile & mode loaded to the keyboard (1-9)
4.5 Open/Close v-Drive (SmartSet + F8)
The Freestyle Edge features a 4MB virtual drive called the “v-Drive” which stores all the custom keyboard
configurations. During normal use the v-Drive is hidden from your computer but it can be temporarily “opened”
using the onboard shortcut. Opening the v-Drive is necessary to 1) run the SmartSet App (see Section XX), 2)
to Direct Program (see Section XX), 3) or update firmware (see Section XX). Note: It is not necessary to
access the v-Drive for basic keyboard use.
When the the v-Drive is open, your computer will now recognize the keyboard as a Removable Storage
Device called “FS EDGE RGB”. The specific appearance and location of the “FS EDGE RGB” drive on your
computer will depend on your operating system.
 Windows: If a pop-up doesn’t appear, open File Explorer and look under “This PC”
 Mac: If the drive does not appear on the desktop, look under “DEVICES”
 Linux : Look in in “MY COMPUTER”
 Chrome: Look in “FILES”
FS Edge RGB
Firmware> 1.0.0.us (4MB), 12/1/2018
Layout> 1
Remaps> 0
Macros> 0
Macro Speed> 5
Game Mode> Off
NKRO Mode> Off
Status Speed 0‐4> 3
LED> 1 Wave

10
Keep the v-Drive closed when not in use: For best results, keep the v-Drive closed when not using the
SmartSet App and refrain from using onboard shortcuts while the v-Drive is open. Note: The keyboard’s
multimedia and mouse actions are disabled while the v-Drive is open.
Always Eject v-Drive before closing: Before closing the v-Drive, it is important to always Eject the “FS
EDGE RGB” drive by right-clicking it in Windows File Explorer, and selecting “Eject”. Once the computer has
ejected the drive, it will notify that it is now safe to close the v-Drive. Ejecting the drive ensures that all
keyboard configuration files have been closed which will prevent data loss and/or corruption. Use the onboard
shortcut (SmartSet + F8) to close the v-Drive.
4.6 Adjust Global Macro Speed (SmartSet + F9, then number row)
The Freestyle Edge can playback macros at one of nine different speeds, ranging from a super-slow 4 actions
-per-second (APS) up to a blazing fast 250 APS! The default Global speed is Speed 5, which is good for text
macros but might be too slow for certain in-game macros. To adjust the Global speed, use the onboard
shortcut to enter Macro Speed Mode and then use the number row to select a speed from 1-9. If you wish to
temporarily disable macro playback without deleting any macros, chose “0” instead. Note: You can override
the Global speed setting and assign a custom, individual playback speed for any given macro using the
SmartSet App (see Section XX) or Direct Programming (see Section XX).
4.7 Enable/Disable NKRO Mode (SmartSet + F10)
NKRO (“n-key rollover”) mode is a special operating mode that allows the keyboard to register all
simultaneous key-presses. Most standard keyboards, and even many gaming keyboards, limit the number of
keys you can press at one time to six (aka “6KRO”). If you press more than 6 keys at a time on a 6KRO
keyboard, the keyboard may fail to register some of those key-presses. 6KRO is fine for basic typing and will
work for most gamers a majority of the time, but hardcore gamers who are playing at lightning-fast speeds
prefer NKRO keyboards for maximum performance. Use the onboard shortcut to toggle NKRO Mode on and
off (the Edge will take a second to re-enumerate). NKRO mode will remain in effect until keyboard is
unplugged or the v-Drive is opened. Confirm NKRO mode with the Status Report.
4.8 Enable/Disable Game Mode (SmartSet + F11)
Game Mode disables all Windows key actions to keep you from accidentally exiting out of your game. Use the
onboard shortcut to toggle Game Mode on and off. The Game Mode indicator LED (“G”) in the upper right
corner of the keyboard will illuminate when Game Mode is enabled.
4.9 Soft Reset (SmartSet + Shift + F12)
Erases all custom remaps and macros in both layers of the active layout.
Seƫng Speed 1 Speed 2 Speed 3 Speed 4 Speed 5 Speed 6 Speed 7 Speed 8 Speed 9
Acons Per Second 4 8 12 22 35 (default) 62 85 125 250
Words Per Minute 48 96 144 264 420 744 1,020 1,500 3,000
*Playback speeds are approximate. Exact speeds will depend on the length of the macro, your computer, and the active application.

11
4.10 Hard Reset (SmartSet + F12 while plugging in keyboard)
Erase all nine layouts and restores the Edge to its factory default settings. XX-LED FILES?
4.11 Refresh Settings (SmartSet + Layout)
The Refresh shortcut is a very important tool if you are programming the keyboard using the SmartSet App or
Direct Programming. The SmartSet App does not dynamically update and changes made do not go into effect
until the v-Drive is closed. Use the Refresh onboard shortcut to implement your changes immediately.
4.12 Program Lock (SmartSet + Shift + L)
Use the Program Lock onboard shortcut to temporarily deactivate the Programming Cluster keys. To disable
Program Lock use the same onboard shortcut.
4.13 Update Firmware (SmartSet + Shift + U)
Periodically Kinesis Gaming will release new versions of firmware for the Freestyle Edge with new features
and bug fixes. Installing new firmware is quick and easy.
1. Obtain a valid Freestyle Edge firmware file (“.upd” file) from KinesisGaming.com/fs-edge-rgb-support
2. Open the v-Drive (SmartSet + F8)
3. Save the new firmware file inside the “firmware” subfolder on the v-Drive
4. Rename the firmware file “update.upd”
5. Press SmartSet + Shift + U to initiate the update
If a valid firmware file has been used, the keyboard will flash and the lights will go off for 10-12 seconds. The
keyboard will then re-enumerate with the new firmware. Run a Status Report to confirm the new firmware has
been installed correctly. Note: Custom layouts and settings are not affected by a firmware update.
4.14 Adjust Status Report Playback Speed (SmartSet + Shift + F7, then 0-4)
Certain computers may have problems playing the Status Report. If you are experiencing a garbled status
report try a reduced playback speed. Use the onboard shortcut to enter Status Speed Mode (LEDs will flash),
then tap “1-4” to select a different speed (default speed is 3), or “0” to disable the Status Report all together.
4.15 Force v-Drive Open (SmartSet + F8 while plugging in keyboard)
If you wish to have the v-Drive open when you plug in the keyboard or are having difficulty accessing the v-
Drive with the normal shortcut, simply hold down this shortcut while plugging in the keyboard.
4.16 Select Lighting Profile (SmartSet + LED Key, then number row)
The Edge has 9 customizable Lighting Profiles. To load a different Lighting Profile simply use the onboard
shortcut above to enter Lighting Profile Selection Mode, then use the number row to chose profile 1 thru 9.
When you are satisfied with your selection, tap the SmartSet key to return the keyboard to normal function.

12
5.0 SmartSet Programming App (Windows)
The SmartSet App lets you design custom layouts, build powerful macros, create unique Lighting Profiles,
and customize keyboard settings with a simple-to-use graphical interface. The App works in conjunction with
onboard programming, but it has several additional tools for power users. Note: The SmartSet App is
Windows only, but Mac & Linux users can still access all of the power-user functionality via Direct
Programming (See Section XX).
The SmartSet App works differently than all other keyboard software so please read these instructions
carefully before using.
5.1 Installing the SmartSet App
To install the SmartSet App, visit the URL below and download the SmartSet App to your Windows PC. The
SmartSet App is a simple, lightweight executable that does not require any special installation or drivers. It
can be saved to your desktop or any folder on your PC, and run from that location. The SmartSet App does
not need to run in the background, and all changes made are saved directly to the keyboard.
KinesisGaming.com/fs-edge-rgb-support

13
5.2 Using the SmartSet App
Since the Freestyle Edge does not utilize any custom drivers, in order for the SmartSet App to communicate
with the keyboard it is necessary to open the keyboard’s “v-Drive” before launching the App (See Section
XX). If you attempt to run the App without first opening the v-Drive, you will receive an error message.
Implementing Changes: The Freestyle Edge does not dynamically update based on changes made
within the SmartSet App. To implement your new keyboard configurations, you must first use the in-App Save
buttons and then close the v-Drive (SmartSet + F8) or use the Refresh Shortcut (SmartSet + Layout). Note:
There are 3 separate Save buttons in the SmartSet: one for Layout changes, one for Lighting changes, and
one for Settings changes.
5.3 Layout Editor
When you first open the SmartSet App, it will automatically load a graphical representation of the active
layout, showing all assigned key actions in both layers, including any custom remaps and macros. If you wish
to view or edit one of the other 8 layouts, click the “Load Layout” button and select the desired layout from the
menu to load it to the SmartSet App for Editing.
Saving Your Layout Changes: Use the “Save Layout” button to save your changes to the indicated Layout File. To
save the layout to a different layout slot or as backup, use the Save As button. Note: Backup layouts cannot be loaded to
the keyboard without first assigning them to one of the 9 numbers slots using Save As.
Designating the Active Key: You may assign any supported key action to any of the 95 full-size keys
(including Fn, the LED key, and both space bars). Select the key you wish to reprogram by clicking the
diagram to designate it as the Active Key and then choose from the Actions Menu at left. Note: The Active
Key will be highlighted to indicate that it is currently designated for reprogramming.
Navigating Layers: Each key has a “top-layer” action and a secondary “Fn-layer” action that can be
customized separately. Use the Layer toggle-switch to move between the layers during programming.
Available Actions:
 Remap: Assign any supported key action by tapping a key on the Edge (or any connected keyboard)
 Macro: Launch the Macro Editor to create a new macro or view an existing macro on the active key
 Media: Play/Pause, Next Track, Previous Track, Mute, Volume Up, Volume Down
1. Load Layout Editor
2. Layout File Loaded for Editing
3. Actions Menu
4. Layer Toggle Switch
5. Load New Layout
6. Save Layout
7. Save Layout As
8. Keyboard Image
9. Tools (Cancel, Accept. Reset
Active Key, Reset All Keys)

14
 Mouse Clicks: Left Click, Middle Click, Right Click, Button 4, and Button 5 (Double-Clicks can be
programmed using the Macro Editor)
 Alternate Layouts: Choose from a pre-configured Dvorak, or Colemak layout
 Disable Key: Disable the action for any key on the keyboard
 Function Keys: F13 - F24
 Numeric Keypad: Assign a full 10-key to the embedded layer or individual keypad actions
 Fn Access: “Fn Toggle” and “Fn Shift” (momentary access)
 LED Control: Toggle Backlighting On/Off
Macro Editor: The SmartSet App can be used to edit macros that were recorded on-the-fly or create
new macros. Keys that have a macro assigned will display with a blue outline. To launch the Macro Editor,
first click on one of the full-size, non-modifier keys in the layout image to act as your primary trigger key
(Note: macros can be assigned to trigger keys in both layers using the Fn toggle switch). Once you have
selected a valid trigger key, click the Macro button in the Actions Menu at left to launch the Macro Editor.
Macro Trigger Key(s): Macros can be triggered solely by the primary key or as a 2-key combination
using a modifier key. To designate a modifier “co-trigger” simply click one of the co-trigger buttons buttons.
Note: Using the Windows key as a co-trigger is not recommended.
Macro Content: After selecting the trigger key(s), click inside the macro text box and type your macro
content. The App will record every single keystroke from the keyboard so if you make a mistake, you’ll need
to use the “Backspace” or “Clear” buttons in the App to edit. Basic alphanumeric characters are displayed in
black text whereas “key actions” are displayed as red text inside of curly brackets as “tokens”. Once you are
done programming your macro, click “Accept” to assign it to the trigger key(s) or click “Cancel” to abandon the
macro. Note:
Common Shortcuts: Use this menu to select from a list of popular pre-programmed macros.
Timing Delays: To perfect the playback of your macro, it may be necessary to insert brief delays in
between certain keystrokes. Select a delay from 1ms to 999ms, or chose a random delay (up to 1000ms) so
that playback is constantly variable.
Mouse Clicks: Use this button to insert a mouse-click into your macro, or to create-your own double-click
macro.
Windows Combos: Use this button to assign a macro using the Windows key without exiting the App.
Copy & Paste: You can copy your favorite macros from one trigger key to another and even between different
layouts using the Copy and Paste buttons.
1. Co-Trigger Buttons
2. Cancel / Accept
3. 3 Macros Per Key
4. Macro Text Box
5. Macro Tools
6. Speed Selector
7. Multiplay Selector

15
Individual Playback Speed: All macros recorded on-the-fly will playback at the keyboard’s “Global Speed”
setting. To achieve optimal playback performance use the “Speed” knob SmartSet App set a custom speed (1
-9) specifically tailored to each macro and its intended playback environment, or choose “G” for Global.
Multiplay: By default each macro will playback only once when the trigger key is held (Multiplay = 1).
Use the “Multiplay” knob in the App to pre-program a macro to playback a specific number of times (up to 9),
or set the knob to repeat to program the macro to fire continuously until the trigger key is released.
Multiple Macros per Key: If you wish to assign a 2nd or even 3rd macro to the same primary trigger key (e.g.,
Right Ctrl+A, Right Shift+A, and Right Alt+A), simply re-select that primary trigger key and then click the “#2” or “#3”
radio buttons to get access a fresh macro text box. To store the new macro you will need to select a unique trigger key
combination using one of the six standard modifiers as a co-trigger.
5.4 Global Keyboard Setting Editor
Global Macro Speed: Set the playback speed for all macros that don’t have an “Individual Playback
Speed” assigned to them, or temporarily disable macros without deleting them. (See Section 5.3 for speeds)
Status Report Speed: The Status Report is a convenient utility that prints-to-the-screen the most
important keyboard settings using the onboard shortcut SmartSet + F7. Just make sure you have a text
editing program open before you try to run a Status Report! The default Status Report playback speed is “3”,
but some computers may require a slower speed for proper playback. If your status report is “garbled”, try
dropping the speed to “2” or even “1”. If you are worried about accidentally triggering the Status Report, just
slide it to “0” to deactivate the Status Report all together.
Game Mode: Game Mode temporarily disables all Windows key actions so you don’t accidentally trigger
a Windows shortcut or switch to your Desktop in the middle of a game. The Game Mode LED will illuminate
when Game is on.
Active Layout: Displays the Layout that is actively loaded to the keyboard. Adjust the knob to have a
different Layout loaded when the v-Drive is closed or the keyboard is refreshed.
Active Lighting: Displays the Lighting Profile that is actively loaded to the keyboard. Adjust the knob
to have a different Lighting Profile loaded when the v-Drive is closed or the keyboard is refreshed.
Saving Your Changes: Use the “Save Settings” button in the pop-up window save your changes to the keyboard. Note:
Global Keyboard Settings are saved independently from Layouts and Lighting Profiles.
Seƫng Speed 1 Speed 2 Speed 3 Speed 4 Speed 5 Speed 6 Speed 7 Speed 8 Speed 9
Acons Per Second 4 8 12 22 35 (default) 62 85 125 250
Words Per Minute 48 96 144 264 420 744 1,020 1,500 3,000

16
5.5 Lighting Editor
There are 9 customizable Lighting Profiles that can easily be selected using the onboard lighting shortcut
(SmartSet + LED then number row). Each of these 9 Lighting Profiles can be assigned one of seven
customizable lighting modes by selecting the mode from the Lighting Effects menu at left.
Lighting Effects
 Individual: Blend custom R-G-B color values (16.8M choices) and assign to each of the 95 backlit keys.
Create intricate patterns, highlight certain key groupings, or use color to indicate custom key actions.
Choose from pre-mixed colors or create and save your own custom palette for use in all your profiles. XX–
Selecting multiple keys
 Monochrome: Select a single color and apply it to all 95 keys.
 Breathe: Assign any color to any key, and then have the keyboard radiate up and down in
soothing pulses. Choose from 9 different speeds.
 RGB Spectrum: All 95 keys cycle through the spectrum of colors. Choose from 9 different speeds.
 RGB Wave: Waves of color ripple across the keyboard. Choose from 9 different speeds and
directions.
 Reactive: Keys light up when typed and fade to black. Choose from 9 different speeds.
 Starlight In progress
 Rebound: In progress
 Ripple: In progress
 Pitch Black: Disable all RGB backlighting and all static indicator LEDs (i.e., Layout, Caps Lock,
Game Mode, Scroll Lock, and Fn)
Saving Changes: Use the “Save Lighting” button to save your changes to the indicated Lighting Profile. To
save the Lighting Profile to a different Lighting Profile slot or as backup, use the Save As button. Note:
Backup Lighting Profiles cannot be loaded to the keyboard without first assigning them to one of the 9
numbers slots using Save As.

17
6.0 Direct Programming (Mac, Linux & Chrome users)
The keyboard’s layouts, lighting profiles, and settings are stored on the v-Drive as a series of simple text files
(.txt), which can be accessed in Windows, Linux, Mac, and Chrome. For those users that do not have access
to a computer that can run the SmartSet App, Direct Programming is a way to access to the various power
user tools which are not otherwise available through onboard programming.
Eject v-Drive before closing (Windows Users)
After editing any .txt files on the v-Drive, it is necessary to first save and close the files, and
then use the Windows eject protocol before closing the v-Drive to prevent data loss/
corruption. Right click the “FS EDGE RGB” removable drive in File Explorer and select
Eject. Once you receive the “Safe to Eject” notification you may proceed to closing the v-
Drive with the onboard shortcut. Failure to eject can result in a minor drive error that
Windows will ask you to repair (see Section 6.7).
Non-US Users: Your computer must be configured for the English (US) keyboard layout. Other
language drivers use different codes/positions for certain keys which are critical for programming characters
such as [], {} and >.
6.1 Direct Programming Layouts
The nine default layouts are saved as separate .txt files in the “layouts”
subfolder. Only custom remaps and macros are saved to the file, so if no
changes have been made to a layout, the file will be empty. Users can either
write code from scratch or edit keyboard-generated code using the syntax rules
described below. Deleting a layout file will permanently delete its stored remaps
& macros, but the keyboard will automatically regenerate a blank layout file.
File Naming Convention: Only the nine numbered layouts can be loaded
to the keyboards. Additional “backup” layouts can be saved as .txt files with
descriptive names, but they cannot be loaded to the keyboard without renaming them.
Syntax Overview: Remaps and macros are encoded in a layout file using a basic programming
syntax. Each of the 95 full-size keys on the keyboard has been assigned a unique “Position” token used to
identify that key during programming (see Section XX). Each keyboard & mouse action supported by the
Edge has been assigned a unique “Action” token corresponding to a standard USB “scan code” (see Section
6.3). Each line of code must include a position token and one or more action tokens. The “>“ symbol is used
to separate position tokens from actions tokens, and individual tokens are surrounded by brackets. Examples:
 Remaps are encoded with Square Brackets: [position]>[action]
 Macros are encoded with Curly Brackets: {position1}{position2}>{action1}{action2}{action3}...
Layout Programming Tips
 If the keyboard cannot understand the desired remap, then the default action will remain in effect.
 Do not mix and match square and curly brackets in a single line of code
 Separate each line of code with Enter/Return

18
 The order in which the lines of code appears in the .txt file does not generally matter, except in the event
of conflicting commands, in which case the command closest to the bottom of the file will be implemented.
 Tokens are not case-sensitive. Capitalizing a token will not produce the capitalized action (see Section
6.5).
 A line of code can be temporarily disabled by placing an asterisk (*) at the beginning of the line.
6.2 Position Token Map
Each physical key has a distinct “position” token for each of the keyboard’s two layers. Top layer position
tokens are shown below in black. In general, to designate a key position in the Fn layer, you simply encode
the prefix “fn“ (with a space) before the basic, top-layer token. The “fn” prefix goes outside of the brackets.
However, for the eight keys which have a unique embedded key action, there is a unique Fn layer token
which corresponds to the embedded layer action for that key position (shown in red below).
Examples:
 Top Caps Lock position is [caps]
 Embedded Hotkey 1 position is: fn [hk1]>...
 Embedded F1 key position is: fn [mute]>...

19
6.3 Key Action Token Dictionary
LeŌShiŌRight ShiŌLeŌAlt Right Alt LeŌWindows
& Command
Right Windows
& Command
LeŌCtrl Right Ctrl
LSHFT RSHFT LALT RALT LWIN RWIN LCTRL RCTRL
Modifiers
Mute Volume
Up
Volume
Down
Play/Pause Next
Track
Previous
Track
MUTE VOL+ VOL‐PLAY NEXT PREV
LeŌ
Mouse
LMOUS
Middle
Mouse
MMOUS
Right
Mouse
RMOUS
Mouse
BuƩon 4
MOUS4
Mouse
BuƩon 5
MOUS5
Multimedia & Mouse Clicks
Open Bracket Close Bracket Period Comma Apostrophe Tilde Forward Slash Back Slash
OBRK CBRK PER COM APOS TILDE / \
Punctuation
Enter Tab Space Delete Backspace Home End Page Up
ENT TAB SPC DEL BSPC HOME END PUP
Page Down
PDN
LeŌArrow Right Arrow Up Arrow Down Arrow Escape Print Screen Pause Scroll Lock Insert
LFT RGHT UP DWN ESC PRNT PAUSE SCRLK INS
Editing & Navigation
Num Lock Keypad 1 Keypad 2 Keypad 3 Keypad 4 Keypad 5 Keypad 6 Keypad 7 Keypad 8
NUMLK KP1 KP2 KP3 KP4 KP5 KP6 KP7 KP8
Keypad 9 Keypad 0 Keypad
Plus
Keypad
Minus
Keypad
Divide
Keypad
MulƟply
Keypad
Enter
Keypad
Equals
Keypad
Decimal
KP9 KP0 KP+ KP‐KP/ KP* KPENT KP= KP.
Numeric Keypad
Caps Lock Fn
Toggle
Fn
ShiŌ
Menu/App InternaƟonal Calculator Shutdown LED
Toggle
CAPS FNTOG FNSHF MENU INTL/ CALC SHTDN LED
Random
Delay
DRAN
Custom
Delay
DXXX
No Key
AcƟon
NULL
Miscellaneous
Function Keys
F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12
F13 F14 F15 F16 F17 F18 F19 F20 F21 F22 F23 F24
A B C D E F G H I J
M N O P Q R S T U V
Y Z 1 2 3 4 5 6 7 8
L
X
0
K
W
9
‐=
Alphanumeric

20
6.4 Programming Remaps
To program a remap, encode the position token and the action token in square brackets, separated by “>“.
Remap Examples:
1. Hotkey 1 performs Q: [hk1]>[q]
2. Escape key performs Caps Lock: [esc]>[caps]
3. The Windows key in the Fn layer performs Right Shift: fn [lwin]>[rshft]
4. F1 in the embedded layer performs Tab: fn [mute]>[tab]
6.5 Programming Macros
Shifted Actions
To produce a shifted key action, it is necessary to encode a macro which includes both the down and up
stroke of the shift key surrounding the basic key action. Downstrokes are indicated by placing a “-” inside the
bracket and upstrokes are indicated by placing “+”. See example 1 below.
Individual Playback Speed Prefix {s_}
By default, all macros play at the selected “Global” playback speed. To assign a custom speed for improved
playback performance for a given macro you can use the “Individual Playback Speed” prefix “{s_}”. Choose a
number from 1-9 corresponding to the speed scale shown Section 4.6. The speed prefix should be placed to
the right of the “>“ before the macro content. See example 2 below.
Multiplay Prefix {x_}
By default, all macros recorded on-the-fly are assigned a multiplay value of 1. Macros can be programmed to
playback up to 9 times using the multiplay prefix, or continuously by eliminating the prefix altogether. Choose
a number from 1-9 corresponding to the number of times you want the macro to replay. The multiplay prefix
should be placed to the right of the “>“ before the macro content. See example 3 below. Note: If a macro is
not playing back properly, it may actually be firing multiple times before you are releasing the trigger key so
confirm the multiplay value is set to 1.
Delays
To improve playback performance or to produce a mouse double-click, you can insert one or more timing
delays at any point within a macro. Delays are any increments of 1ms between 1ms and 999ms. Simply enter
the token {dXXX} where XXX corresponds to the desired duration in milliseconds (e.g., {d050} creates a 50
millisecond delay). Multiple tokens can be stacked sequentially to create longer delays.
In some gaming environments it may be desirable to have macro that plays back with different timing each
instance. To insert a Random Delay, this insert the {dran} token throughout your macro which will cause a
random delay between 1ms and 150ms for each instance of the token.
Macro Examples:
1. Pause key performs “Hello” with a capital H: {pause}>{-lshft}{h}{+lshft}{e}{l}{l}{o}
2. Hotkey 5 performs “qwerty” at speed 9: {hk5}>{s9}{q}{w}{e}{r}{t}{y}
3. Hotkey 1 increases the volume 3 notches: {hk1}>{x3}{vol+)
4. Tab key performs a left-mouse double click: {tab}>{lmous}{d125}{lmous}
5. Left Shift + Hotkey 2 produces “abc” with variable timing {lshft}{hk2}>{a}{dran}{b}{dran}{c}