King Industrial nova 83705 User manual

INSTRUCTION MANUAL
COPYRIGHT © 2022 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.
MODEL: 83750
SAFETY GUARD WITH LIMIT SWITCH
Designed to fit NOVA Viking DVR Drill Press
(model 83705)

WARRANTY INFORMATION
2-YEAR
LIMITED WARRANTY
FOR THIS SAFETY GUARD
KING CANADA TOOLS
OFFERS A 2-YEAR LIMITED WARANTY
FOR NON COMMERCIAL USE.
PROOF OF PURCHASE
Please keep your dated proof of purchase for warranty and servicing purposes.
LIMITED TOOL WARRANTY
King Canada makes every effort to ensure that this product meets high quality and
durability standards. King Canada warrants to the original retail consumer a 2-year
limited warranty as of the date the product was purchased at retail and that each
product is free from defects in materials. Warranty does not apply to defects due
directly or indirectly to misuse, abuse, normal wear and tear, negligence or
accidents, repairs done by an unauthorized service center, alterations and lack of
maintenance. King Canada shall in no event be liable for death, injuries to persons
or property or for incidental, special or consequential damages arising from the use
of our products.
To take advantage of this limited warranty, return the product at your expense
together with your dated proof of purchase to an authorized King Canada service
center. Contact your retailer or visit our web site at www.kingcanada.com for an
updated listing of our authorized service centers. In cooperation with our authorized
serviced center, King Canada will either repair or replace the product if any part or
parts covered under this warranty which examination proves to be defective in
workmanship or material during the warranty period.
NOTE TO USER
This instruction manual is meant to serve as a guide only. Specifications and
references are subject to change without prior notice.
KING CANADA INC. DORVAL, QUÉBEC, CANADA H9P 2Y4
www.kingcanada.com

Assembly
Note: The following instructions use the Viking
DVR Drill Press model 83705 for the Safety
Guard installation procedures.
1) Slide the mount bracket (A) Fig.1 of the
Safety Guard assembly onto the Drill Press
quill. Secure the mount bracket (A) to the
quill by tightening cap screw (B) Fig.1. Only
tighten enough to secure assembly to quill,
do not overtighten cap screw.
2) Now the limit switch cable with connector (A)
Fig.2 must be connected to the connector
(B) found on the left side of the head.
Remove rubber cap (C), align the connector
holes with the pins and push to connect.
3) The Safety Guard (A) Fig.3 height can be
adjusted by loosening lock knob (B) and
lowering Safety Guard. This Safety Guard
also comes with a guard extension (C) which
can be lowered to cover the entire chuck
body. The guard extension position can be
lowered as shown by loosening lock knobs (D).
Operational Guidelines & Firmware
Note: The entire chuck body must be covered
by the Safety Guard/Safety Guard Extension.
All Viking Drill Presses come with a firmware
with an "automatic" self enable for the Safety
Guard. In order to activate the "automatic" self
enable function, make sure the Safety Guard is
installed and the cable connector is plugged
into the Viking Drill Press. Turn on Viking Drill
Press, the firmware will recognize and
automatically enable the Safety Guard
software.
When the Safety Guard is opened, the Drill
Press will automatically detect the Safety Guard is open and will turn off the machine.
The Drill Press can only be operated while the Safety Guard is completely closed.
At this point, it is important to test the firmware to make sure the Safety Guard works as
intended. Turn machine on, open the Safety Guard. The machine must stop and the LCD
screen will indicate “Chuck Guard Open”. The drill press will not be able to start again
until the safety guard is completely closed.
If you wish to disable the Safety Guard, disconnect and remove the Safety Guard.
Perform a factory reset (press and hold “Self Start” while short pressing the “OFF”
button) to turn off the Safety Guard software.
ASSEMBLY &
OPERATIONAL GUIDELINE
Figure 1
Figure 2
Figure 3
PARTS DIAGRAM & PARTS LISTS
Refer to the Parts section of the King Canada web site for the most updated parts diagram
and parts list.