King Quest VQ4200 User manual

VQ4200 Owner’s Manual
For Bell TV™ (Canada) and DISH® (USA)
This manual contains detailed information on your KING Quest.
To start watching TV right away,
use the Quick Reference Guide.
TM

Page 1
TABLE OF CONTENTS
2
3
3
4
5
6
7-8
9
10-11
12-18
20-21
22-25
26
26
27
28
29
PRODUCT REGISTRATION
To provide ongoing technical support and to better
facilitate warranty processing, please register your product
at www.kingconnect.com/products/product-registration/.
IMPORTANT!
The satellite TV market is expanding and changing. The information in this manual was accurate at the time of
visit our website at www.kingconnect.com. KING is not responsible for changes outside of its control.
Please read this Owner’s Manual thoroughly before using or installing the KING Quest. See additional

Page 2
Thank you for purchasing a KING antenna!
Bell TV
DISH
Approximate Coverage Map for Bell TV
Approximate Coverage

Page 3
3 APPLY RUBBER FEET TO ANTENNA UNIT
Unbox contents and verify everything is present.
IMPORTANT!
If you are going to permanently roof mount the
antenna unit, DO NOT apply the rubber feet.
See the roof installation section later in this manual.

Page 4
4 CONNECTIONS
A
B
C
D
optional second receiver use.
Make connections A-D in order shown.

Page 5
POWER COAX
CONNECTION
POWER SCAN
OFF
ON
SCAN
SCAN
COAX CONNECTION SCAN PROGRESS
POWER
ALARM OPERATION
POWER

Page 6
POWER COAX
CONNECTION
SCAN COAX CONNECTION SCAN
PROGRESS
SCAN
SCAN
SCAN PROGRESS COAX CONNECTION
POWER
BELL HD AND SD
DO NOT CHOOSE ANY GRAYED OUT SERVICE OPTION.

Page 7
POWER COAX CONNECTION
SCAN
SCAN PROGRESS
4. GO TO NEXT PAGE TO CONFIGURE RECEIVER.
7 BELL: INITIAL SCAN AND RECEIVER CONFIGURATION
IMPORTANT!
Any tall objects can block
the signal from reaching
the antenna.
Place the antenna unit in a position with a clear view of
the southern sky to scan for the satellites.
Bell TV

Page 8
MENU
Point Dish
SELECT
BELL RECEIVER CONFIGURATION
SELECT
You can now use the instructions in the BELL: OPERATION section for subsequent use.
Bell TV SD Bell TV HD and SD
“None”
Bell TV
NO “X”s

Page 9
IMPORTANT! Make sure you have completed section 7, INITIAL SCAN AND RECEIVER CONFIGURATION
before continuing below.
IMPORTANT!
Any tall objects can block
the signal from reaching
the antenna.
Place the antenna unit in a position with a clear view
of the southern sky to scan for satellites.
POWER COAX CONNECTION
SCAN
SCAN PROGRESS
4. Watch TV. Enjoy!
PLEASE BE PATIENT!
Bell TV

Page 10
INITIAL SETUP FOR SECOND RECEIVER
MENU
Point Dish
SELECT
See the next page for downloading programming to the second receiver.
SELECT
Antenna locked on
and
receiver connected!
Bell TV

Page 11
DOWNLOADING PROGRAMMING TO THE SECOND RECEIVER
POWER
NOTE:
Bell TV

Page 12
SAT
RECORD
SELECT
Portable Antenna Setup
IF YOU ARE USING A NEW RECEIVER WITH THE KING QUEST, YOU MUST FOLLOW
THE FIRST TIME SETUP PROCEDURE STARTING BELOW.
AFTER THIS FIRST TIME PROCEDURE, YOU CAN USE “STANDARD OPERATION
FIRST TIME OPERATION WITH NEW DISH RECEIVER
MAKE SURE TO INSTALL THE BATTERIES IN THE RECEIVER’S REMOTE
DISH

Page 13
LINE OF SIGHT TO THE SATELLITES IN THE
SOUTHERN SKY AT ANY TIME!
SELECT.
SELECT
SELECT
IMPORTANT!
If you move the antenna unit any
time during or after the scan,
DISH

Page 14
Mobile Antenna Setup
DISH

Page 15
Acquiring Signal
This completes the setup for new receivers. You may now use
STANDARD OPERATION WITH DISH RECEIVER starting on the next page for subsequent use.
DISH

Page 16
SELECT
Mobile Antenna Setup
Note: If the Mobile Antenna Setup
remote. Highlight the “Check Switch” button then press SELECT on your remote.
STANDARD OPERATION WITH DISH RECEIVER
LINE OF SIGHT TO THE SATELLITES IN THE
SOUTHERN SKY AT ANY TIME!
IMPORTANT!
If you move the antenna unit any
time during or after the scan,
IF YOUR RECEIVER IS NEW AND UNACTIVATED, YOU MUST COMPLETE
DISH

Page 17
SELECT
SELECT
Acquiring Signal
DISH

Page 18
OPERATING NOTES:
error message does not appear.
REACQUIRE THE SATELLITES AND RESTORE PROGRAMMING.
DISH