KING KS User manual

41100018

90°
27.5"
(70cm)
19.5"
(50cm)
Top View
63"-67"
(160cm-170cm)
90°
19.5"
(50cm)
Side View
Remote Installation Notes:
Indoor Monitor
The proper height of indoor monitor or outdoor station is b e t ween
63"-67"(160-170cm) from the ground.This may vary on each
installation. View range should be actively tested before complete.
Installing units too close to ele ctrica l l i n e s /dimmers/ballasts/or
other electrical devices may cause audio and/or video interference.
Narrow spa ce may cause feedback echo on monitor v o i c e
function. .
Direct sunshine can cause blu rry or g h o s t - like picture on monitor.
Viewing window of door camera is a b o u t 19.5 (50cm) vertically "
and 27.5" (70cm) horizontally.
Outdoor Station
-1-

-2-
FOUR MONITORS WITH TWO ENTRANCES
Indoor Monitor with external power supply

-3-
FOUR MONITORS WITH TWO ENTRANCES
Indoor Monitor with external power supply

1.If you want to connect indoor monitor to multi-button outdoor station
Keep pressing on indoor monitor 3 seconds, when you hear a long
sound"di", means change mode success.
2.If you want to connect indoor monitor to one call button outdoor station
Keep pressing on indoor monitor 3 seconds, when you hear a long
sound"ding-dong", means change mode success.
3.How to use J1 & J2 jumper on backside of indoor monitor Master
Monitor Jumper
J1=ON for 1 monitor in Loop, OFF all other items.
Video Termination-IMPORTANT
J2=ON for Last monitor in Loop, OFF all the items.
st
MULTI-BUTTON OUTDOOR WITH MONITORS
Important
-4-

1.Maximum 3 Indoor Monitors and 1 Outdoor Station .
3.Each monitor is individually powered.
4.Cables of system: wire ≥0.5 mm , from outdoor station to the farthest
indoor monitor distance ≤70m.
2.Parallen connection.
NOTES:
SYSTEM DIAGRAM
-5-
2

DC 12V 1A (12W)
Specification
IconNo.Description IconNo.Description
Product Views
-6-

OPERATION
Press at anytime,the
Indoor Monitor will show
the image from the door
camera automatically.
Press to have
communication with the
visitor.
After pressing the unlock
button, the Indoor Monitor
still display the image form
the door camera
-7-

This function is to see
the image from the door
camera.
How to send SOS alarm:
Under monitoring or when talking with
visitors, press SOS to send alarm, stop
SOS alarm by pressing any button for 1
second, then press any button to exit.
-8-

When visitor call, monitor will take an video automatically , and save in SD
card. Max allow 32G SD card .
Picture Memory Function
In calling mode, Pictures are taken & stored automatically in monitor
image memory.
To check image: In standby mode press ( page up, page down)
To delete single image: Press & confirm
To delete all images: Press for 3 seconds. Press multiple
times to select"Delete All"
Press to select "Photo"& Press delete all photos.
Press to Exit.
Video Recording & check function
SD card is required to store videos
To record Video: In call from door camera status or manual door
camera monitor status, press for 3 seconds. Press to select
"Video" then press to start recording.
To play recorded Video: In standby mode, press for 3 seconds.
Press multiple times & select"Play", and then press to play.
Press to exit.
Delete all videos or photos: Press for 3 seconds.
Press multiple times to select"Delete All"
Press , Select Video & press , It will display
Then press , Select"yes"& then press to delete all saves
videos. Press to Exit.
SD card can be used in PC/Laptops for watching video or deleting
videos.
-9-

1.Power off, press and keep holding, switch on the power.After 3 seconds,
heard DiDiDi...release * button.
2.Enter 4 digits as new programming password, a long Di sound, means success.
(2-6 digits allowed),the length same as original code)
3.Press * to exit.
*
Enter programming mode
1.Press (a Di sound ), enter 4 digits programming password(2-6 digits allowed,
default programming code is 1234). After a long Di sound, it says enter the
programming mode.
2. It’ll exit the programming mode within 30 seconds without any operations
(DiDiDiDi sound means exit).
*
3.Press * to exit.
Factory default unlock delay is 1 second.
2.Press 00, a long Di sound , enter 2 digits(from 01-99)as unlock time. After a
long Di sound , it says set success.
3.Press * to exit.
1.Enter programming mode (*1234), a long Di sound.
1.Enter programming mode (*1234), a long Di sound.
means set success.
3.Press * to exit.
(Attention: after change length of password, all passwords were cleared out.
e.g. length of password set as 3, then programming password will be 123.)
2.Press 99, a long Di sound, then enter digits from 2-6 , a long Di sound again
Operations for keypad door station
Modify the programming password
Setting the length of password
Set unlocking time delay
Attention
1.The default program password is 1234.
2.Each keypad door station allow 40 groups use passwords to
unlock door.
3.The password to enter programming mode, we call it
programming password.The password to open the door, we call
it user password.
-10-

1.Enter programming mode (*1234), a long Di sound.
2.Enter 2 digits position from 01-40, a long Di sound.
Press # , another Di sound again. means delete it.
3.Press * to exit.
1.Enter programming mode (*1234), a long Di sound.
2.Press #, DiDi sound, press # one more time, a long Di sound, press # 7 times,
after 3 seconds, a long Di sound , means deleting success. After that, the
unlock time delay changes to 1 second , and clear out all user passwords, but
programming password no change(1234).
3.Press * to exit.
Switch off power , press # and keep holding, switch on the power.
After a long Di sound , release #, means restoring success.
The default programming password is 1234 , and clear out all the user passwords.
Delete one user password(input position)
Delete user password(input user password)
1.Enter programming mode (*1234), a long Di sound.
2.Press # , DiDi sound, enter that 4 digits password you want to delete
(can be 2-6digits). After a long Di sound, means deleting success.
3.Press * to exit.
1.Enter programming mode (*1234), a long Di sound.
2.Enter 2 digits position from 01-40, a long Di sound.
3.Press 4 digits password(2-6 digits),after a long Di sound, means add success.
4.Press * to exit.
Delete all settings
Restore factory mode
Add user passwords
Attention:each door station keypad have 40 positions(01-40), each position
allow one password.Position 31-40 cant set unlock delay, beacuse there’re
used for dry contact lock(NO/NC).
-11-