Kirby Morgan SuperLite 17B User manual

WARNING
Diving with compressed breathing gas is a hazardous activity. Even if you do everything
right there is always the danger that you may be killed or injured. No piece of diving
equipment can prevent the possibility that you may be killed or injured any time you
enter the water.
SuperLite®17B Helmet
Operations and Maintenance Manual
KMDSI Part # 100-001
Kirby Morgan Dive Systems, Inc.
1430 Jason Way
Santa Maria, CA 93455, USA
Telephone (805) 928-7772, FAX (805) 928-0342
Manual prepared by Marine Marketing and Consulting, Dive Lab, Inc., and KMDSI.
NOTE: This manual is the most current for the SuperLite®17B Helmet. It is page dated June 2012. Future changes
will be shown on page III and the changed pages will carry the date of change. Previous manuals may not reect
these updates.
™
Document Number 120613005
Kirby Morgan, SuperLite®, BandMask, Band Mask, KMB, KMB-Band Mask, DSI, Diving Systems International, EXO, REX,
SuperFlow®and DECA are all registered trademarks of Kirby Morgan Dive Systems, Inc. Use of these terms to describe products
that are not manufactured by KMDSI is illegal.
The two dimensional images (such as photographs and illustrations) of our products are © copyrighted and trademarks of Kirby
Morgan Dive Systems, Inc. The three dimensional forms of our products are trademark, trade design and trade dress protected.
© ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. This manual is made available for the express use of the owner of
this Kirby Morgan product. No part of this manual may be reproduced, stored in any retrieval system, or transmitted, or used in any
form or by any means, whether graphic, electronic, mechanical, photocopy, or otherwise by technology known or unknown, without
the prior written permission of Kirby Morgan Dive Systems, Inc.
The SuperLite®-17A/B helmet is CE Approved and meets or exceeds all performance and testing
requirements of all government and non-government testing agencies throughout the world. It is ap-
proved for use on all commercial and military work underwater.

SuperLite®17B
II © ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 120613005
Warranty Information
Kirby Morgan Dive Systems, Inc. warrants every new mask, helmet, or KMACS 5 Air Control
System to be free from defects in workmanship for a period of three hundred sixty ve (365) days
from date of purchase. This warranty covers all metal, berglass, and plastic parts. This warranty
does NOT cover rubber parts, communications components, or head cushions. In addition, due to
the electrolytic nature of underwater cutting and welding, chrome plating cannot be warranted when
the diver engages in these activities.
Should any part become defective, contact the nearest authorized KMDSI dealer. If there is no
dealer in your area, contact KMDSI directly at (805) 928-7772 x 229. You must have a return autho-
rization from KMDSI prior to the return of any item, Upon approval from KMDSI, return the defec-
tive part, freight prepaid, to the KMDSI plant. The part will be repaired or replaced at no charge as
deemed necessary by KMDSI.
This warranty becomes null and void if:
1) The product is not registered with KMDSI within ten (10) days of purchase.
2) The product has not been properly serviced and/or maintained according to the appropriate
KMDSI manual. In addition, the user is responsible to ensure that all product updates as
recommended by KMDSI have been performed.
3) Unauthorized modications have been made to the product.
4) The product has been abused or subjected to conditions which are unusual or exceed the
product’s intended service.
NOTE: Be sure to complete the enclosed warranty card and return it to KMDSI immediately. No
warranty claims will be honored without a satisfactorily completed warranty card on le at KMDSI.

SuperLite®17B
© ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 120613005 III
It is the responsibility of the owner of this product to register their ownership with Kirby Morgan Dive
Systems, Inc., by sending the warranty card provided. This card is to establish registration for any necessary
warranty work and as a means of communication that allows KMDSI to contact the user regarding this product.
The user must notify KMDSI of any change of address by the user or sale of the product.
All changes or revisions to this manual must be recorded in this document to ensure that the manual is
up to date. Quantities marked in parenthesis.
Record Of Changes
Change Number Date Description of Change
1 05/28/2008 Reworded: 2.1 Product Specications, 2.4 Operational Specications & Limitations,
Warnings Corrected, 7.12.1 to the correct 7.16.1 and Table of Contents Updated.
Added: Appendix A2, 3 and 4
Moved: 2.4 Operational Specications & Limitations, The SuperFlow®Demand
Regulator Image Rotated and Scaled to t.
Removed: Table 1 and Table 2 from chapter 2.
2 08/20/2008 Page III Removed page number column.
Page 16 First paragraph Part number added to Hard Shell.
Page 17 Second paragraph 77 added to list of helmets.
Chapter 1 rearranged and CE text added to KM-77 description.
Pg 63 and 64 Chapter 5 made to two columns format and font changed to lower
case instead of all caps.
Page 65 Added Whisker Clamp Replacement Kit: Part # 525-032.
Page 66 Corrected text to read “SL 17” instead of “KM 37 and 57” in 6.2, last
sentence and photo caption.
Page 102 step 17 corrected, "sssembly" to read "assembly."
Page 173 Torque Specication corrections.
Page 174 Added note about thread locking compound.
3 03/13/2009 Page 75: Space added between 6.5.1 Quad.
Page 77: Removed grammatical error beneath image.
Page 81: Corrected 40 inch pounds to 35 inch pounds in step 3. Lacquer thinner
changed to acetone.
Page 82: Corrected 40 inch pounds to 15 inch pounds in step 6. Lacquer thinner
changed to acetone.
Page 95: Corrected amount omitted inch pounds to 40 inch pounds in step 6.
Page 105: Corrected 75 inch pounds to 100 inch pounds twice in step 18. Corrected
30 inch pounds to 40 inch pounds in step 22.
Page 120: Corrected 75 inch pounds to 100 inch pounds in step 4.
Page 122: Corrected 75 inch pounds to 100 inch pounds in step 8. Corrected 35 inch
pounds to 40 inch pounds in step 9.
Page 124: Removed step 11 and merged SPECIAL CARE text with step 10. Cor-
rected 75 inch pounds to 100 inch pounds in step 16.
Page 136: Corrected 35 inch pounds to 20 inch pounds in step 4.
Page 140: Corrected 30 inch pounds to 20 inch pounds in step 3.
Page 143: Corrected 35 inch pounds to 35-50 inch pounds in step 1.
Page 152: Corrected 15 inch pounds to 20 inch pounds in step 5.

SuperLite®17B
IV © ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 120613005
Change Number Date Description of Change
3 (Continued) 03/13/2009 Page 154: Corrected 35 inch pounds to 25 inch pounds in step 5. Grammatical error,
"resuse" corrected to reuse in step 7. Corrected 35 inch pounds to 20 inch pounds
in step 1 of section 8.10.1.2. Corrected 35 inch pounds to 20 inch pounds in step 3
of section 8.10.1.2.
Page 175: Location #94's part number corrected from 530-045 to 530-040. Added
location #'s 6, 107 and 152a.
4 07/23/2009 CE material added
5 10/05/2009 Changed location # 82's part number from 550-372 to 550-038 in the torque specs.
6 11/06/2009 Chapter 2: addition of CE conforming criteria.
7 04/19/2010 Updated images and diagrams with new whiskers.
8 07/20/2010 Added wiring diagram to chapter 8.
9 04/06/2011 Updated earphones throughout manual
10 06/17/2011 Changed 61 meters to 67 meters in Appendix 3 Table 3 SuperFlow®350 Regulator
High Pressure Regulated Source
11 10/17/2011 Updated CE notifying body number from 0496 to 2049
12 05/09/2012 Updated CE notifying body address
13 05/13/2012 Updated copyright date to roman numerals
Diving with compressed breathing gas is a hazardous activity. Even if you do everything
right there is always the potential for serious injury or death. No one piece of diving
equipment can prevent the possibility that you may be injured or killed any time you
enter the water. We do not herein make any effort to teach the principles of diving. The
information in this manual is intended for users of Kirby Morgan helmets and persons
that maintain or service Kirby Morgan helmets.
WARNING

SuperLite®17B
© ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 120613005 V
Table Of Contents
Warranty Information �������������������������������������������������������������������������������� II
Record Of Changes �������������������������������������������������������������������������������� III
Denition of Signal Words Used in this Manual ������������������������������������������������� XI
Chapter 1 General Information KMDSI Products����������������������������������� 1
1.1 Introduction �������������������������������������������������������������������������������������� 1
1.2 Full-Face Masks and Manifolds���������������������������������������������������������������� 2
1.3 Kirby Morgan Diving Helmets ������������������������������������������������������������������ 4
Chapter 2 Description & Operational Specications - SuperLite®-17B �� 9
2.1 CR Marking �������������������������������������������������������������������������������������� 9
2.2 CE Certication ���������������������������������������������������������������������������������� 9
2�2�1� CE Marking ��������������������������������������������������������������������������������� 9
2�2�2� Notied Body ������������������������������������������������������������������������������ 10
2.3 Product Specications������������������������������������������������������������������������� 10
2.4 Regulator Performance ������������������������������������������������������������������������ 10
2.5 Cage Code �������������������������������������������������������������������������������������� 10
2.6 Operational Specications & Limitations ���������������������������������������������������� 10
2.7 Helmet Features �������������������������������������������������������������������������������� 11
2.8 General Description ���������������������������������������������������������������������������� 13
2�8�1 Helmet Shell �������������������������������������������������������������������������������� 13
2�8�2 Gas Flow Systems �������������������������������������������������������������������������� 13
2�8�3 Emergency Gas Supply System (EGS) ������������������������������������������������������ 18
2�8�4 Helmet Attachment to the Diver������������������������������������������������������������� 18
2�8�5 Sealing Arrangement ����������������������������������������������������������������������� 18
2�8�6 Reducing Carbon Dioxide ������������������������������������������������������������������ 19
2�8�7 Communications���������������������������������������������������������������������������� 20
2�8�8 Equalizing the Middle Ear ������������������������������������������������������������������� 20
2�8�9 Face Port or Viewing Lens ������������������������������������������������������������������ 21
2�8�10 Latch Catch Assembly, Pull Pin������������������������������������������������������������ 21
2.9 Accessories ������������������������������������������������������������������������������������� 21
2�9�1 Eye Protection for Welding������������������������������������������������������������������ 21
2�9�2 Hot Water Shroud��������������������������������������������������������������������������� 22
2�9�3 Special Regulator Tools��������������������������������������������������������������������� 22
2.10 Helmet Transport And Storage �������������������������������������������������������������� 23
2�10�1 Helmet Carrying Bag ���������������������������������������������������������������������� 24
2.11 Use of Kirby Morgan Original Replacement Parts ����������������������������������������� 24
Chapter 3 Operating Instructions�������������������������������������������������������� 25
3.1 Introduction ������������������������������������������������������������������������������������� 25
3.2 Design Purpose��������������������������������������������������������������������������������� 25
3.3 First Use of Your Kirby Morgan Diving Helmet ���������������������������������������������� 27
3.4 Initial Adjustments to Your Helmet������������������������������������������������������������ 27
3�4�1 Head Cushion ������������������������������������������������������������������������������ 27
3�4�2 Adjusting the Neck Dam �������������������������������������������������������������������� 28
3.5 Pre Dress-In Procedure ������������������������������������������������������������������������ 29

SuperLite®17B
VI © ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 120613005
3�5�1 Pre-Dive Visual Inspection ������������������������������������������������������������������ 29
3.6 Preparing the Helmet for Diving��������������������������������������������������������������� 30
3�6�1 Clean Face Port ���������������������������������������������������������������������������� 30
3�6�2 Check Moving Parts ������������������������������������������������������������������������ 30
3�6�3 Check Communications �������������������������������������������������������������������� 30
3�6�4 One-Way Valve Check ���������������������������������������������������������������������� 30
3.7 Emergency Gas System (EGS) ���������������������������������������������������������������� 31
3.8 Setting Up to Dive ������������������������������������������������������������������������������ 35
3�8�1 Flushing Out the Umbilical ������������������������������������������������������������������ 35
3�8�2 Connecting the Umbilical to the Helmet ���������������������������������������������������� 35
3�8�3 Opening the Breathing Gas Supply to the Helmet ������������������������������������������ 36
3�8�4 Fogging Prevention ������������������������������������������������������������������������� 36
3�8�5 Donning The SuperLite®-17B ��������������������������������������������������������������� 37
3�8�6 Testing the Breathing System ��������������������������������������������������������������� 42
3�8�7 Sealing Integrity Check ��������������������������������������������������������������������� 42
3.9 Diving Procedures������������������������������������������������������������������������������ 43
3�9�1 Standing By to Dive������������������������������������������������������������������������� 43
3�9�2 Attaching the Umbilical to the Harness ����������������������������������������������������� 43
3�9�3 Diver Dons Helmet�������������������������������������������������������������������������� 43
3�9�4 Diver Check Gas Flow Systems������������������������������������������������������������� 43
3�9�5 Communications Check �������������������������������������������������������������������� 43
3�9�6 Diver Ready��������������������������������������������������������������������������������� 43
3�9�7 Water Entry and Descent ������������������������������������������������������������������� 44
3.10 Emergency Procedures ���������������������������������������������������������������������� 44
3�10�1 Flooding ����������������������������������������������������������������������������������� 44
3�10�2 Inhalation Resistance���������������������������������������������������������������������� 44
3�10�3 Gas Flow Stops ��������������������������������������������������������������������������� 44
3�10�4 Demand Regulator Free Flow�������������������������������������������������������������� 45
3.11 Post Dive Procedures������������������������������������������������������������������������ 45
3�11�1 Removing the Equipment������������������������������������������������������������������ 45
3�11�2 Removing the Helmet ��������������������������������������������������������������������� 45
3�11�3 Storage of the Helmet Between Dives ����������������������������������������������������� 46
Chapter 4 Troubleshooting������������������������������������������������������������������ 47
4.1 General ������������������������������������������������������������������������������������������ 47
4.2 Communication Malfunction ������������������������������������������������������������������ 47
4.3 One Way Valve Malfunction ������������������������������������������������������������������� 47
4.4 Side Valve Malfunction������������������������������������������������������������������������� 48
4.5 Water Leakage Into Helmet ������������������������������������������������������������������� 48
4.6 Demand Regulator Malfunction��������������������������������������������������������������� 49
4.7 Emergency Gas Supply Valve ����������������������������������������������������������������� 49
Chapter 5 Inspection and Maintenance ����������������������������������������������� 51
5.1 Routine Maintenance �������������������������������������������������������������������������� 51
5�1�1 Daily Pre-Dive Maintenance A2�3 ����������������������������������������������������������� 51
5�1�2 Daily Post Dive Maintenance A2�6 ���������������������������������������������������������� 51
5�1�3 Supervisors Equipment Checks A2�4 and A2�5 ��������������������������������������������� 51
5.2 Monthly Maintenance �������������������������������������������������������������������������� 51
5.3 Yearly Maintenance ���������������������������������������������������������������������������� 51

SuperLite®17B
© ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 120613005 VII
5�3�1 Overhaul/Inspection Checklist A2�1��������������������������������������������������������� 51
Chapter 6 General Preventative Maintenance ������������������������������������� 53
6.1 Introduction ������������������������������������������������������������������������������������� 53
6.2 Required tools, Cleaning Agents, Lubrication ����������������������������������������������� 53
6�2�1 Component and Parts Cleaning������������������������������������������������������������� 54
6�2�2 Component and Parts Lubrication ��������������������������������������������������������� 54
6�2�3 Teon®Tape �������������������������������������������������������������������������������� 55
6�2�4 RTV Sealant �������������������������������������������������������������������������������� 55
6�2�5 Thread Locker ������������������������������������������������������������������������������ 55
6.3 General Cleaning & Inspection Procedures�������������������������������������������������� 55
6�3�1 O-Ring Removal/Inspection/Cleaning and Lubrication �������������������������������������� 56
6�3�2 General Cleaning Guidelines���������������������������������������������������������������� 56
6�3�2�1 Mild Soap Solution for ������������������������������������������������������������������� 57
General Cleaning and Leak Detector Use��������������������������������������������������������� 57
6.3.2.2 Acidic Cleaning Solution and Procedures ���������������������������������������������������� 57
6.3.2.3 Germicidal Cleaning Solutions and Procedure ������������������������������������������������ 57
6.4 Daily Maintenance ����������������������������������������������������������������������������� 59
6.5 Monthly Inspections ��������������������������������������������������������������������������� 61
6�5�1 Quad-Valve™ Exhaust System ������������������������������������������������������������� 61
6�5�2 Emergency Valve Assembly����������������������������������������������������������������� 62
6�5�3 Steady Flow/Defogger Valve ���������������������������������������������������������������� 62
6�5�4 Bias Device Adjustable Section of Demand Regulator ������������������������������������� 62
6�5�5 Neck Clamp and Yoke Assembly ����������������������������������������������������������� 62
6�5�6 Latch Catch Mechanism �������������������������������������������������������������������� 62
Chapter 7 Breathing System Maintenance and Repairs ����������������������� 63
7.1 Introduction ������������������������������������������������������������������������������������� 63
7.2 One Way Valve ���������������������������������������������������������������������������������� 63
7�2�1 Disassembly Of The One Way Valve �������������������������������������������������������� 63
7�2�2 Reassembly of the One Way Valve���������������������������������������������������������� 64
7.3 Side Block Assembly��������������������������������������������������������������������������� 65
7�3�1 General ������������������������������������������������������������������������������������� 65
7�3�2 Side Block Assembly Removal�������������������������������������������������������������� 65
7�3�3 Separating the Side Block Assembly from the Helmet Shell �������������������������������� 66
7�3�4 Side Block Assembly Replacement ��������������������������������������������������������� 68
7.4 Defogger Valve ��������������������������������������������������������������������������������� 69
7�4�1 Disassembly of the Defogger Valve ��������������������������������������������������������� 69
7�4�2 Cleaning and Lubricating������������������������������������������������������������������� 69
7�4�3 Reassembly of the Defogger Valve ��������������������������������������������������������� 70
7.5 Emergency Valve Assembly ������������������������������������������������������������������� 71
7�5�1 Disassembly of the Emergency Valve ������������������������������������������������������� 71
7�5�2 Cleaning and Lubricating ������������������������������������������������������������������� 71
7�5�3 Reassembly of Emergency Valve ����������������������������������������������������������� 72
7�5�4 Leak Testing the EGS Valve ����������������������������������������������������������������� 73
7.6 Bent Tube Assembly ��������������������������������������������������������������������������� 74
7�6�1 General ������������������������������������������������������������������������������������� 74
7�6�2 Removal of the Bent Tube Assembly�������������������������������������������������������� 74
7�6�3 Inspection of Bent Tube Assembly ���������������������������������������������������������� 75

SuperLite®17B
VIII © ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 120613005
7�6�4 Installation of the Bent Tube Assembly������������������������������������������������������ 75
7.7 Hose Assembly (SL-17A only)����������������������������������������������������������������� 76
7�7�1 Hose Assembly Removal ������������������������������������������������������������������� 76
7�7�2 Hose Assembly Inspection “A” style Side Block �������������������������������������������� 76
7�7�3 O-Ring Replacement ����������������������������������������������������������������������� 76
7�7�4 Hose Assembly Replacement��������������������������������������������������������������� 76
7�8�2 SuperFlow®Demand Regulator Test for Correct Adjustment, Fully Assembled ������������� 77
7.8 SuperFlow®Demand Regulator ��������������������������������������������������������������� 77
7�8�1 General Regulator Information �������������������������������������������������������������� 77
7�8�3 Inspection of SuperFlow®Regulator Body Interior ������������������������������������������ 78
7�8�4 SuperFlow®Demand Regulator Bias Adjustment Servicing, Demand Regulator on the Helmet
��������������������������������������������������������������������������������������������������� 79
7�8�5 Reassembly of the SuperFlow®Regulator Adjustment System������������������������������ 80
7�8�6 SuperFlow®Demand Regulator Removal from Helmet�������������������������������������� 81
7�8�7 Disassembly of the SuperFlow®Demand Regulator����������������������������������������� 82
7�8�8 Inspection of SuperFlow®Demand Regulator Parts����������������������������������������� 85
7�8�9 Reassembly of the SuperFlow®350 Demand Regulator ������������������������������������ 87
7�8�10 Tuning the SuperFlow®Regulator���������������������������������������������������������� 91
7.8.10.1 Important Notes on Regulator Adjustment �������������������������������������������������� 92
7�8�11 SuperFlow®Regulator Steady Flows When Pressured Up: Special Tools Used ������������ 93
7�8�12 Regulator Steady Flows When Pressured Up ��������������������������������������������� 95
7�8�13 Regulator has Low or No Flow When Pressurized ����������������������������������������� 95
7�8�14 Unexplained Demand Regulator Free Flow ������������������������������������������������ 95
7.9 Oral Nasal ��������������������������������������������������������������������������������������� 96
7�9�1 Oral Nasal General Information ������������������������������������������������������������� 96
7�9�2 Oral Nasal Removal ������������������������������������������������������������������������ 96
7�9�3 Inspection of Oral Nasal �������������������������������������������������������������������� 96
7�9�4 Oral Nasal Replacement �������������������������������������������������������������������� 97
7.10 Quad-Valve™ Exhaust Assembly������������������������������������������������������������ 98
7�10�1 Quad-Valve™ Assembly Removal ��������������������������������������������������������� 98
7�10�2 Quad-Valve™ Exhaust Valve Replacement ������������������������������������������������ 99
7�10�3 SuperFlow®Regulator Exhaust Valve Replacement�������������������������������������� 102
7�10�4 Quad-Valve™ Assembly Installation ���������������������������������������������������� 103
7.11 Water Dump Exhaust Body ���������������������������������������������������������������� 103
7�11�1 Water Dump Valve Removal ������������������������������������������������������������� 103
7�11�2 Water Dump Valve Replacement �������������������������������������������������������� 103
7�11�3 Water Dump Valve Body Removal ������������������������������������������������������ 103
7�11�4 Water Dump Valve Body Remounting ��������������������������������������������������� 103
7.12 Reinstalling the Quad-Valve™ Exhaust Assembly �������������������������������������� 105
7�13 Standard Old Style Single Exhaust Whisker PN# 510-554��������������������������������� 106
7�13�1 Whisker Removal ������������������������������������������������������������������������ 106
7�13�2 Reinstalling the Whisker ����������������������������������������������������������������� 107
7.14 Double Exhaust Whisker ������������������������������������������������������������������� 108
7�14�1 Double Exhaust Whisker Cleaning and Overhaul, Whisker PN# 525-102 ���������������� 108
7.15 Tri-Valve Exhaust Whisker������������������������������������������������������������������ 110
7�15�1 Demand Regulator Assembly Removal �������������������������������������������������� 110
7�15�2 Replacing the Regulator Exhaust Valve �������������������������������������������������� 110

SuperLite®17B
© ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 120613005 IX
7�15�3 Tri-Valve Exhaust Valve Replacement���������������������������������������������������� 111
7�15�4 Installing the Tri-Valve Exhaust System onto the Regulator ������������������������������ 113
7.16 Overpressure Relief / Bleed Valve Overhaul Procedures�������������������������������� 114
7�12�1 Overpressure Relief Valve ��������������������������������������������������������������� 114
7�16�2 Overpressure Relief Valve Disassembly and Cleaning ����������������������������������� 114
7�16�3 Overpressure Relief Valve Reassembly �������������������������������������������������� 115
7�16�4 Overpressure Relief Valve Lift Check/Setting �������������������������������������������� 115
Chapter 8 Corrective Maintenance���������������������������������������������������� 117
8.1 General ���������������������������������������������������������������������������������������� 117
8.2 Yoke/Neck Clamp Assembly and Helmet Shell Inspection������������������������������� 117
8.3 Nose Block Assembly������������������������������������������������������������������������ 119
8�3�1 Nose Block Assembly Removal����������������������������������������������������������� 119
8�3�2 Nose Block Device Replacement ��������������������������������������������������������� 120
8.4 Handle and Weights�������������������������������������������������������������������������� 121
8�4�1 Handle Removal ������������������������������������������������������������������������� 121
8�4�2 Handle Replacement ��������������������������������������������������������������������� 122
8�4�3 Weight Removal �������������������������������������������������������������������������� 123
8�4�4 Weight Replacement���������������������������������������������������������������������� 123
8.5 Chin Strap and Yoke Strap ������������������������������������������������������������������ 125
8�5�1 Chin Strap Removal ���������������������������������������������������������������������� 125
8�5�2 Chin Strap Replacement������������������������������������������������������������������ 125
8�5�3 Removal of the Yoke Strap���������������������������������������������������������������� 126
8�5�4 Replacement of the Yoke Strap ����������������������������������������������������������� 126
8.6 Alignment Sleeve ����������������������������������������������������������������������������� 128
8�6�1 Sleeve Removal and Inspection����������������������������������������������������������� 128
8�6�2 Sleeve Replacement ���������������������������������������������������������������������� 128
8.7 Port Retainer���������������������������������������������������������������������������������� 129
8.8 Face Port�������������������������������������������������������������������������������������� 129
8�8�1 General ����������������������������������������������������������������������������������� 129
8�8�2 Face Port and Nose Block Device Removal����������������������������������������������� 129
8�8�3 Face Port and Nose Block Replacement�������������������������������������������������� 130
8�8�4 Special Note Regarding Ports ������������������������������������������������������������ 132
8.9 Communications System �������������������������������������������������������������������� 133
8�9�1 General ����������������������������������������������������������������������������������� 133
8�9�2 Earphone Inspection���������������������������������������������������������������������� 133
8�9�3 Microphone Removal and Replacement �������������������������������������������������� 134
8�9�4 Earphone Removal and Replacement����������������������������������������������������� 135
8�9�5 Waterproof Connector ������������������������������������������������������������������� 135
8.9.5.1 Connector Removal ��������������������������������������������������������������������� 135
8.9.5.2 Connector Replacement����������������������������������������������������������������� 136
8�9�6 Communications Posts ������������������������������������������������������������������� 137
8.9.6.1 Communications Post Removal ���������������������������������������������������������� 137
8.9.6.2 Communications Post Replacement ������������������������������������������������������ 137
8.10 Neck Clamp/Yoke Assembly ��������������������������������������������������������������� 138
8�10�1 Yoke ������������������������������������������������������������������������������������ 138
8.10.1.1 Yoke Removal and Disassembly ��������������������������������������������������������� 138
8.10.1.2 Yoke Replacement and Reassembly ����������������������������������������������������� 140

SuperLite®17B
X © ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 120613005
8�10�2 Latch Catch Assembly ������������������������������������������������������������������ 140
8.10.2.1 Latch Catch Mechanism Disassembly���������������������������������������������������� 140
8.10.2.2 Latch Catch Mechanism Reassembly ���������������������������������������������������� 141
8�10�3 Neck Clamp Assembly ������������������������������������������������������������������ 141
8.10.3.1 Neck Clamp Assembly Adjustment /Inspection�������������������������������������������� 141
8�10�4 Neck Dam ������������������������������������������������������������������������������ 143
8.10.4.1 Neck Dam Replacement���������������������������������������������������������������� 143
Pre-84 and Cold Water Type Neck Dam ��������������������������������������������������������� 144
Installation ������������������������������������������������������������������������������������ 144
8.10.4.2 Four Hole Method of Attaching Neck Dam to Hinge Tab������������������������������������ 145
8.10.4.3 Patch Method of Attaching Neck Dam to Hinge Tab ��������������������������������������� 146
8.10.4.4 Drawstring Type Neck Dam Installation ��������������������������������������������������� 146
8.11 O-Ring Seal Replacement������������������������������������������������������������������ 148
8.12 Head Cushion Foam Replacement�������������������������������������������������������� 148
Chapter 9 Accessories���������������������������������������������������������������������� 149
9.1 Introduction ����������������������������������������������������������������������������������� 149
9.2 Hot Water Shroud General������������������������������������������������������������������� 149
9�2�1 Installation of the Hot Water Shroud ������������������������������������������������������ 149
9.3 Low Pressure Inator Hose Installation on the B Sideblock ����������������������������� 151
9.4 Weld Lens & Weld Shield Assemblies ������������������������������������������������������ 152
9.5 Use of Quick Disconnect �������������������������������������������������������������������� 154
9.6 Double Exhaust System ��������������������������������������������������������������������� 155
9�6�1 Double Exhaust Kit Installation������������������������������������������������������������ 155
Table of Equivalents�������������������������������������������������������������������������� 159
Appendix 1: Torque Specications ���������������������������������������������������� 160
Note on Torque Specications ���������������������������������������������������������� 161
Checklist, Maintenance, and Pre-Dive Inspections ������������������������������������������� 161
Appendix A2 Maintenance and Inspection Procedures ���������������������� 162
Appendix 3 Supply Pressure Requirements & Tables ������������������������� 164
Appendix 3 Table 1 Work Rate Expressed as Respiratory Minute Volume (RMV)* ��������� 165
Appendix 3 Table 2 Compressor Supply Table SuperFlow®and SuperFlow®350���������� 165
Appendix 3 Table 3 SuperFlow®350 Regulator High Pressure Regulated Source ��������� 167
Appendix 4 Standard Kirby Morgan Surface Supply Pressure Formula -
Old Method��������������������������������������������������������������������������������������� 167

SuperLite®17B
© ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 120613005 XI
For your protection, pay particular attention to items identied by signal words in this manual. These terms are identied
as, CAUTION, WARNING AND DANGER. It is especially important for you to read and understand these sections.
This word indicates an imminently hazardous situation, which if not avoided, could re-
sult in death or serious injury.
This word indicates a potentially hazardous situation, which, if not avoided, could result
in death or serious injury.
This word indicates a potentially hazardous situation, which if not avoided, may result in
minor or moderate injury. It may also be used to alert against unsafe practices.
If English is not your native language and you have any difculty understanding the language of any warn-
ings as they appear in the manual, please have them translated.
Este é um aviso importante. Queira mandá-lo traduzir.
Este es un aviso importante. Sirvase mandario traducir.
Quest è un avviso importante. Tradurlo.
Ceci est important. Veuillez traduire.
Diese Mitteilung ist wichtig. Bitte übersetzen lassen.
If you have any questions concerning this manual or the operation of your helmet, contact KMDSI (805)
IMPORTANT: A word about this manual. We have tried to make this manual as comprehensive and factual as pos-
sible. We reserve the right, however, to make changes at any time, without notice, in prices, colors, materials, equip-
ment, specications, models and availability. Since some information may have been updated since the time of print-
ing, please contact your local KMDSI dealer if you have any questions. Periodically KMDSI Operations and Mainte-
nance Manuals are reviewed. Any updates/changes will be posted on the KMDSI website and may be downloaded for
insertion/correction.
Important Safety Information:This SuperLite®17B diving helmet is intended for use by trained divers who have
successfully completed a recognized training course in surface supplied diving
CAUTION
Denition of Signal Words Used in this Manual
DANGER
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING

SuperLite®17B
XII © ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 120613005
WARNING
Follow all the instructions in this manual carefully and heed all safety precautions. Im-
proper use of this diving helmet could result in serious injury or death.
WARNING
Kirby Morgan Dive Systems, Inc. (KMDSI) warns all divers who use Kirby Morgan div-
ing helmets or masks to be sure to use only KMDSI original parts from a KMDSI au-
thorized dealer. Although other parts, O-rings and ttings may appear to t your Kirby
Morgan diving helmet or mask, they may not be manufactured to the same standards
maintained by KMDSI. The use of any parts other than KMDSI original parts may lead to
equipment failure and accidents.
WARNING
Diving in waters that are chemically, biologically, or radiologically contaminated is ex-
tremely hazardous. Although Kirby Morgan diving helmets may be adapted for use in
some contaminated environments, special training, equipment, and procedures are
necessary. Do not dive in a contaminated environment unless you have been thoroughly
trained and equipped for this type of diving.
WARNING
This helmet was completely checked and should be ready to dive as it was shipped
from the factory. However, it is always the diver’s responsibility to check all the compo-
nents of the helmet prior to diving.
Read this manual before using or maintaining the helmet, even if you have experience with other diving helmets. If
you have purchased the helmet new from a dealer, be sure to send in the warranty registration card so we may
keep you informed of any safety notices that affect this product. If you resell or loan this helmet to another diver,
be sure this manual accompanies the helmet and that the person reads and understands the manual. In addition to the
manual a log book should be used to log all repairs, maintenance and use.
WARNING
Diving is a life threatening occupation. Even if you do everything right you can still be
killed or injured. None of the models of Kirby Morgan helmets or masks can prevent ac-
cidents, injuries or death due to improper training, poor-health, improper supervision,
improper job requirements, improper maintenance or acts of God.
WARNING
Any and all berglass repairs done to this helmet MUST be done by a KMDSI factory
trained repair facility. Painting is not recommended by KMDSI. Furthermore, many div-
ing companies will not allow painted helmets to be used because painting can mask
previous berglass damage. KMDSI certied technicians are not responsible for certify-
ing helmets free from damage during annual overhauls.
Helmet shells can be re-gel coated by authorized/certied KMDSI trained technicians
that have received berglass training by KMDSI. Helmets that are to be painted for
cosmetic purposes, should be rst, certied free of berglass damage by an authorized
KMDSI technician certied in berglass repair. A log entry should be made in the hel-
met log that the helmet was free of damage prior to painting. Keep in mind other KMDSI
technicians can refuse to work on helmet shells that have previously been painted or
repaired by non KMDSI certied persons.
WARNING

SuperLite®17B
© ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 120613005 XIII
This manual is supplied to the original purchaser of this helmet. If you have any questions about the use of the helmet
or you need another copy of this manual, contact KMDSI or your nearest KMDSI dealer. It may also be downloaded
free from the KMDSI website at www.KirbyMorgan.com.
WARNING
KMDSI helmets and masks are intended for underwater use only and should only be
used by qualied divers that have received proper training in the use of this type of
equipment. KMDSI helmets and masks should not be used or worn without the appro-
priate life support systems, such as air or gas supplies and support personnel as de-
scribed in this manual.
If you have any questions regarding the use, maintenance, or operation of this helmet, contact KMDSI at (805) 928-
7772, fax: (805) 928-0342, or e-mail: [email protected].
Components requiring lubrication, should only be lubricated with oxygen compatible lubricants such as Christo-
Lube®, Flourolube, or Krytox®. Lubricants must be used sparingly and should not be mixed with other lubricants.
The information contained in this manual is intended to aid the user in optimizing the performance of this helmet.
The application of some of this information will depend on the diving situation and the use of associated equipment.
Many countries have specic laws and rules regarding commercial diving. It is important for the user to understand
the rules, regulations, and philosophy imposed by the governing, regulating bodies whenever using commercial diving
equipment.
KMDSI helmets and masks should never be used for motor sport racing, aviation /
space craft use, or for chemical warfare use. The helmet must never be used by per-
sons in poor physical condition, by persons with previous head, neck, or back injuries
which could be aggravated by its use. The helmet should not be used by persons un-
der the inuence of drugs or alcohol. Furthermore, infants, children, or persons under
the age of 18 should never wear KMDSI helmets and masks. Failure to pay heed to the
above could result in serious injury or death.
WARNING
WARNING
Do not use KMDSI masks or helmets in currents exceeding 3.0 knots Use in currents
greater than 3 knots may allow water to enter the exhaust valve, possibly causing regu-
lator ooding. This could lead to drowning.
Surface-supplied diving can be a strenuous activity. The SuperLite®-17B weighs approx-
imately 30 lbs. KMDSI recommends that persons with a previous neck or back injury
seek professional medical approval prior to engaging in surface supplied diving opera-
tions using the SuperLite®-17B. Use of the SuperLite®-17B with a pre-existing physical/
medical condition may result in death or serious injury.
WARNING

SuperLite®17B
XIV © ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 120613005
WARNING
Always read the Material Safety Data Sheet (MSDS) for any chemical - adhesive, clean-
ing agent, or lubricant - used on your Kirby Morgan helmet. Some of these chemicals
may cause serious bodily injury or death if used improperly or without the proper per-
sonal protective equipment.
WARNING
Never use the helmet without rst completing all pre-dive maintenance and set up
procedures. Failure to complete all pre-dive checks could result in helmet failure due to
problems with the incorrect set-up of the equipment. This could lead to serious person-
al injury or death.
Whenever KMDSI helmets or masks are used in European Countries, which have adopted the C.E. certication
programs, they must only be used with C.E. certied components. Diving operations should only be conducted within
the limits of the operational specications, and in accordance with the rules and regulations established by the gov-
erning authority in the specic country or geographical location where the diving operations are being conducted. If
you have any questions concerning this manual or the operation of your helmet, contact KMDSI (805) 928-7772 or at

SuperLite®17B
© ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 120613005 1
This manual will refer to location numbers in specic drawings, or in the exploded view, which is
in the back of this manual. These numbers are called “location” numbers. They are used to nd
the referred to parts in the drawings in this manual only. They are not the part number. Next to
the exploded drawing is a list of the “location” numbers that match the Kirby Morgan part num-
bers along with the name of the part. Always check the part number when ordering to make sure
it is correct. When ordering, always specify the helmet model number and serial number as well.
The Kirby Morgan Corporation was started in 1965.
The copper and brass “Heavy Gear” or “Standard
Dress” helmets were the rst helmets manufactured
by the company. Over the years Kirby Morgan de-
signed, manufactured and sold many different hel-
mets and masks for commercial divers.
Staying active in commercial diving has contributed
to the successful design innovations of KMDSI
products. This may be the primary reason for the ac-
ceptance of our designs by professional divers.
Bev Morgan has designed more than fty-seven div-
ing helmets and over 40 diving masks. All employees
of KMDSI participate as part of the Kirby Morgan
design team. It would not be possible for us to sup-
ply the commercial, military, scientic, and public
service diving industries with our equipment, without
the team of people that make up Kirby Morgan Dive
Systems, Inc. (KMDSI)
We feel it is important for the reader to understand
that we at KMDSI consider ourselves as only part
of the process along the path in diving equipment
design. We welcome all input from our customers.
The thinking of many good divers, diving equipment
engineers, diving medical specialists, diving organi-
zation administrators and their supporting personnel
has contributed to the current state of the art of diving.
Each piece of gear we manufacture has in it some of
the thinking of those who have gone before us. To
all those people who gave something of themselves
to the men and women who work underwater, we
express a thank you.
We have a strong commitment to providing the best
diving equipment and service possible. This thinking
has been the policy of Kirby Morgan Dive Systems,
Inc. and we will continue to take this approach to
our work.
Our extensive dealer network makes it easy to obtain
genuine Kirby Morgan replacement parts, as well as
technical assistance worldwide.
KMDSI has always concentrated on designing and
manufacturing diving equipment that allows most
repairs, inspections, and all routine maintenance to
be performed by the user. Most routine preventative
and corrective maintenance can be accomplished by
the user utilizing this manual, the KMDSI Tool Kit
(P/N 525-620) and common hand tools. Technician
training is available through Dive Lab Inc. Informa-
tion can be obtained on line at www.divelab.com or
by telephone at 850-235-2715.
Chapter 1
General Information KMDSI Products
1.1 Introduction
Bev Morgan, Chairman of the Board Kirby Morgan
Dive Systems, Inc.
STOP!
BEFORE GOING FURTHER-

SuperLite®17B
2 © ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 120613005
The EXO Full Face Mask is designed for both
surface supplied and scuba diving. By enclosing the
divers eyes, nose and mouth, the EXO permits nearly
normal speech when used in conjunction with most
wireless, and all hard wire underwater communica-
tion systems.
The EXO BR (BALANCED REGULATOR)
shown here is designed to meet or exceed recom-
mended performance goals in both scuba and surface
supplied modes and is approved. It meets and sur-
passes European standards for regulator performance.
The Balanced Regulator helps reduce the work of
breathing for the diver by balancing the intermediate
air pressure against the valve sealing pressure inside
the regulator. This enables the regulator to instantly
adjust to changes in line pressure. The balanced
regulator is adjustable for a wide range of intermedi-
ate pressures between 90 PSIG – 250 over ambient
pressure (6.2 – 17 bar).
Both models have a modular communications de-
sign that permits rapid and simple maintenance. The
optional Hard Shell provides surfaces for mounting
lights, cameras etc.
KMB 18 A/B
The KMB 18B Band Mask frame is constructed of
hand laid berglass. The head harness is a molded,
strong tear resistant neoprene rubber.
The hood, which attaches to the mask frame with
welded stainless steel bands, provides warmth for
the divers head as well as pockets for the earphones.
The communications connections can be either a male
waterproof plug in type or bare wire posts. Both this
mask and the KMB 28B feature the new Tri-Valve™
Exhaust System.
The KMB 28B Band Mask (not shown) is very simi-
lar to the KMB 18, with many parts on the KMB 18B
being interchangeable with the KMB 28B. The major
difference between the 18 and 28 is the material of the
mask frame itself. The KMB 18 has a berglass frame
(yellow) while the KMB 28B frame is an extremely
durable injection molded plastic (black).
Other differences include:
1) The main exhaust body of the KMB 28 is part of
the frame itself and uses a #545-041 main exhaust
cover
2) no comfort insert is required on the 28
3) the face ports for the 18 and the 28 differ slightly
in size.
Both the KMB 18 and KMB 28 are approved.
C
O
M
M
E
R
C
I
A
L
L
Y
R
A
T
E
D
-
P
R
O
F
E
S
S
I
O
N
A
L
D
I
V
I
N
G
G
E
A
R
-
D
I
V
E
L
A
B
T
E
S
T
E
D
™
EXO BR
C
O
M
M
E
R
C
I
A
L
L
Y
R
A
T
E
D
-
P
R
O
F
E
S
S
I
O
N
A
L
D
I
V
I
N
G
G
E
A
R
-
D
I
V
E
L
A
B
T
E
S
T
E
D
™
1.2 Full-Face Masks and Manifolds
approved and
™
marked
approved and
™
marked

SuperLite®17B
© ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 120613005 3
The SuperMask M-48 is an innovative new design
in a full-face mask. It provides the diver with all the
comfort of a full-face mask with the convenience
of changeable second stage regulators as well as the
ability to use a snorkel without having to remove
the mask.
The mask is comprised of two major components,
the mask frame and the interchangeable lower pod.
The removable lower pod is a feature unique to the
SuperMask full-face mask. When diving, the pod is
easily removed and replaced on the mask, providing
the diver the capability to buddy-breathe, snorkel,
use an octopus or perform an “in water” gas switch.
With the pod sealed to the mask, the exible, silicone
pod cover allows the diver to quickly place the regula-
tor mouthpiece into the mouth or dive with it free of
the mouth for communications. With the mouthpiece
in, the regulator may be used without the pod being
sealed to the mask.
The mask may also be used surface supplied when
used with the proper accessories. We are currently
developing several different pod congurations for
both open circuit and rebreather use. For further
information, see the Frequently Asked Questions
(FAQ) area on
our web site at www.KirbyMorgan.
com/FullFaceMasks/M48.html.
The Kirby MorganAir Control System-5 (KMACS)
is a lightweight, portable control box for use in sur-
face supplied air diving operations. The KMACS-5
controls the diver’s air supply, communications and
monitors the diver’s depth. It allows two divers clear
push-to-talk (two wire) or round robin (four wire)
communications. The KMACS-5 is also available
without communications.
The air supply can be either from a low-pressure
compressor or high-pressure cylinders. The adjust-
able rst stage regulator reduces the high-pressure
air and supplies low pressure through the umbilical
to the diver’s breathing system.
High pressure yokes permit U.S. standard scuba
cylinders or DIN equipped cylinders to be used. Low-
pressure air supply ttings allow for a compressor to
be used as the primary air source.
A complete pneumo system with dual reading gauges
(both US Standard and Metric) is provided for each
diver’s air, as well as a shut-off/bleed system that uses
two high-pressure feed lines which allows changing
of used cylinders without interruption of the diving
operation. Optional shut off valves allow the isolation
of each diver’s air supply.
The Communication Set is a multipurpose intercom-
munication system that provides reliable and clear
communications between a topside operator (tender)
and one or more surface-supported divers, recompres-
sion chambers, or other submersible systems.
KMACS-5
w/ No Communications
KMACS-5
w/ Communications
C
O
M
M
E
R
C
I
A
L
L
Y
R
A
T
E
D
-
P
R
O
F
E
S
S
I
O
N
A
L
D
I
V
I
N
G
G
E
A
R
-
D
I
V
E
L
A
B
T
E
S
T
E
D
™
approved and
™
marked
SuperMask M-48
w/ Scuba Pod
SuperMask M-48
w/ Rebreather pod
C
O
M
M
E
R
C
I
A
L
L
Y
R
A
T
E
D
-
P
R
O
F
E
S
S
I
O
N
A
L
D
I
V
I
N
G
G
E
A
R
-
D
I
V
E
L
A
B
T
E
S
T
E
D
™
C
O
M
M
E
R
C
I
A
L
L
Y
R
A
T
E
D
-
P
R
O
F
E
S
S
I
O
N
A
L
D
I
V
I
N
G
G
E
A
R
-
D
I
V
E
L
A
B
T
E
S
T
E
D
™
™
marked

SuperLite®17B
4 © ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 120613005
1.3 Kirby Morgan Diving Helmets
All Kirby Morgan diving helmets and masks are
manufactured by Kirby Morgan Dive Systems, Inc.
(KMDSI). Each step of the manufacturing process is
carefully controlled to assure the customer of a high
quality, durable helmet that will function properly
for many years.
There are eight models of Kirby Morgan diving hel-
mets currently in production. They are the SuperLite®-
17B, (MK-21- U.S. Navy version), SuperLite® 17C
the SuperLite® 27, and Kirby Morgan models 37,
37SS, 47, 57, and 77. All are ™ marked.
The SuperLite®-17 A/B was rst developed in 1975
and quickly set a new standard for diving helmet
design. Many large and small commercial diving
companies, military organizations, scientic divers,
and public safety divers are successfully using this
design around the world. This helmet is marked.
The SL-17 A/B helmet system consists primarily of
two major components: the neck dam/yoke assem-
bly, and the helmet. To don the helmet, the diver
rst slips the angled neck dam with the attached
yoke over their head. The helmet is lowered onto
the diver’s head with the help of a tender, then the
yoke hinge tab is hooked onto the alignment screw
on the rear weight. The neck clamp is then slipped
onto the helmet and locked. The locking system
not only seals the neck dam to the helmet but also
secures the front of the yoke, fastening the helmet
to the diver’s head.
The SuperLite®-17A/B shares many common breath-
ing system parts with all Kirby Morgan helmets and
masks. The breathing system was man-tested to
1600 FSW by the University of Pennsylvania and
approved by the U.S. Navy for surface-supplied div-
ing to 190 FSW with air and 300 FSW with mixed
gas. It surpasses all requirements of all governing
agencies and it is approved for commercial diving
through out the world.
SuperLite®17A/B Kirby Morgan 37
Yoke and Latch Catch
Assembly
Neck Pad and
Sealed Pull Pins.
C
O
M
M
E
R
C
I
A
L
L
Y
R
A
T
E
D
-
P
R
O
F
E
S
S
I
O
N
A
L
D
I
V
I
N
G
G
E
A
R
-
D
I
V
E
L
A
B
T
E
S
T
E
D
™
approved and
™
marked approved and
™
marked

SuperLite®17B
© ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 120613005 5
Other features that are common to all Kirby Morgan
helmets include:
* Face port and retainer ring
* Communications components
* Oral nasal mask
* Nose block device
* Air train defogger
The Kirby Morgan 37 Commercial Diver’s Helmet
represents what we at Kirby Morgan consider to be
a turning point in modern diving helmet design. The
helmet consists of two major assemblies: the helmet
shell/helmet ring assembly and the neck dam/neck
ring assembly.
The helmet comes with the large tube SuperFlow®
350 adjustable demand regulator which provides an
easier breathing gas ow during peak work output.
A quick change communications module is available
with either bare wire posts or a waterproof connector.
The helmet ring houses the sealed pull pins and pro-
vides protection for the bottom end of the helmet. The
diver is also provided with an internally adjustable
chin support. This custom t and balance seats the
helmet comfortably for long periods of time even
when working in the face down position.
The SuperLite®27® Commercial Diver’s Helmet has
all the same features of the KM37 on a smaller, low
volume shell design. This helmet is often preferred
by persons with smaller heads.
The chrome plated machined brass helmet neck ring
houses the sealed pull pins and provides protection
for the bottom end of the helmet. Like the SL-17K,
37 and 17C, the diver is provided with an internally
adjustable chin support. This support, along with the
adjustable neck pad on the locking collar, gives the
diver a comfortable, secure, custom t.
The quick-change communications module, available
with either bare wire posts or a waterproof connector,
allows for easy, efcient maintenance of the helmets
communications.
The helmet also features the SuperFlow® 350 large
tube adjustable demand regulator. The helmet is
available in the umbilical over the shoulder, “B”
conguration only.
SuperLite®27®
C
O
M
M
E
R
C
I
A
L
L
Y
R
A
T
E
D
-
P
R
O
F
E
S
S
I
O
N
A
L
D
I
V
I
N
G
G
E
A
R
-
D
I
V
E
L
A
B
T
E
S
T
E
D
™
The Kirby Morgan 47 offers the ultimate in a high
performance breathing regulator. This helmet has an
entirely new breathing system, oral nasal mask, and
water ejection system. The REX Demand Valve, with
it’s fully adjustable balanced piston is a breakthrough
design that exceeds the requirements of all govern-
ment or other testing agencies.
It has the best work-of-breathing performance when
compared to ANY other commercial diving helmet.
The Kirby Morgan 47 Dive Helmet has been tested
and meets or exceeds European CE requirements and
is fully commercially rated. In all other respects, this
helmet is nearly identical to the Kirby Morgan 37.
C
O
M
M
E
R
C
I
A
L
L
Y
R
A
T
E
D
-
P
R
O
F
E
S
S
I
O
N
A
L
D
I
V
I
N
G
G
E
A
R
-
D
I
V
E
L
A
B
T
E
S
T
E
D
™
Kirby Morgan 47
approved and
™
marked
approved and
™
marked

SuperLite®17B
6 © ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 120613005
The Kirby Morgan 57 helmet features our revo-
lutionary new SuperFlow® 450 Stainless Balanced
Regulator. It's machined from a stainless steel casting
for the ultimate in performance and reliability.
Like all KMDSI regulators on our helmets and
Band Masks, we use only regulators that are speci-
cally designed for surface-supplied diving, that will
perform over the wide range of pressures delivered
by low pressure compressors. An ordinary SCUBA
regulator mounted on a diving helmet is not capable
of delivering the gas you need at heavy work loads.
This commercially rated fully diver adjustable regu-
lator delivers all the breathing gas you might require
for the most demanding work underwater.
The Kirby Morgan 57 also includes our Quad-
Valve™ Exhaust System. It's recommended for div-
ing in biologically contaminated water, when you're
properly trained and equipped, using recommended
procedures. This new exhaust has exceptionally low
exhalation resistance that you must experience to
appreciate.
C
O
M
M
E
R
C
I
A
L
L
Y
R
A
T
E
D
-
P
R
O
F
E
S
S
I
O
N
A
L
D
I
V
I
N
G
G
E
A
R
-
D
I
V
E
L
A
B
T
E
S
T
E
D
™
™
marked
BWARNING
Before attempting any diving in any
type of contaminated water, a com-
plete diving and topside course in
hazardous materials emergencies
should be completed. The divers and
the topside team must be properly
trained and have the proper safety
equipment. All helmets and suits can
leak water under certain conditions.
Divers should use extreme caution
when diving in contaminated waters.
The Kirby Morgan®77 represents the rst in a new
generation of stainless steel diving helmets that pro-
vide an alternative for the diver who prefers a metal
helmet. The helmet features a stainless steel version
of our new REX® regulator, which offers the best
performance of any Kirby Morgan system.
It has the best work-of-breathing performance when
compared to ANY other commercial diving helmet.
The Kirby Morgan 77 Dive Helmet has been tested
and meets or exceeds European CE requirements and
is fully commercially rated.
The advantages of this all stainless steel helmet in-
clude the following:
• No renishing required if the surface is scratched
or gouged.
• Faster production of helmets for customer delivery.
• Elimination of threaded inserts for securing the port
retainer to the helmet shell.
• No need to remove the handle to remove the port
retainer.
• One piece sideblock includes both the free-ow
valve and the Emergency Gas System valve.
• The helmet ring is an integral part of the helmet.
®
approved and
™
marked
Other manuals for SuperLite 17B
2
Table of contents
Other Kirby Morgan Motorcycle Accessories manuals