Kirby Morgan 47 User manual

WARNING
Diving with compressed breathing gas is a hazardous activity. Even if you do everything
right there is always the danger that you may be killed or injured. No piece of diving
equipment can prevent the possibility that you may be killed or injured any time you
enter the water.
Kirby Morgan 47 Helmet
Operations and Maintenance Manual
KMDSI Part #100-070
Patented, Foreign Patents Pending, other patents apply.
Kirby Morgan Dive Systems, Inc.
1430 Jason Way
Santa Maria, CA 93455, USA
Telephone (805) 928-7772, FAX (805) 928-0342
Manual prepared by Marine Marketing and Consulting, Dive Lab, Inc., and KMDSI.
NOTE: This manual is the most current for the Kirby Morgan 47 Helmet. It is page dated June 2012. Future changes
will be shown on page III and the changed pages will carry the date of change. Previous manuals may not reect
these updates.
K
I
R
B
Y
M
O
R
G
A
N
D
I
V
E
S
Y
S
T
E
M
S
,
I
n
c
.
Document Number 120614002
The Kirby Morgan 47 helmet meets or exceeds all performance and testing requirements of all gov-
ernment and non-government testing agencies throughout the world. They are CE approved. It is
approved for use on all commercial and military work underwater.
Kirby Morgan, SuperLite®, BandMask, Band Mask, KMB, KMB-Band Mask, DSI, Diving Systems International, EXO, REX®,
SuperFlow®and DECA are all registered trademarks of Kirby Morgan Dive Systems, Inc. Use of these terms to describe products
that are not manufactured by KMDSI is illegal.
The two dimensional images (such as photographs and illustrations) of our products are © copyrighted and trademarks of Kirby
Morgan Dive Systems, Inc. The three dimensional forms of our products are trademark, trade design and trade dress protected.
© ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. This manual is made available for the express use of the owner of
this Kirby Morgan product. No part of this manual may be reproduced, stored in any retrieval system, or transmitted, or used in any
form or by any means, whether graphic, electronic, mechanical, photocopy, or otherwise by technology known or unknown, without
the prior written permission of Kirby Morgan Dive Systems, Inc.

II © ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #120614002
Kirby Morgan®47
Warranty Information
Kirby Morgan Dive Systems, Inc. warrants every new mask, helmet, or KMAC Air Control System
to be free from defects in workmanship for a period of three hundred sixty ve (365) days from date
of purchase. This warranty covers all metal, berglass, and plastic parts. This warranty does NOT
cover rubber parts, communications components, or head cushions. In addition, due to the electro-
lytic nature of underwater cutting and welding, chrome plating cannot be warranted when the diver
engages in these activities.
Should any part become defective, contact the nearest authorized KMDSI dealer. If there is no
dealer in your area, contact KMDSI directly at (805) 928-7772. You must have a return authoriza-
tion from KMDSI prior to the return of any item, Upon approval from KMDSI, return the defec-
tive part, freight prepaid, to the KMDSI plant. The part will be repaired or replaced at no charge as
deemed necessary by KMDSI.
This warranty becomes null and void if:
1) The product is not registered with KMDSI within ten (10) days of purchase.
2) The product has not been properly serviced and/or maintained according to the appropriate
KMDSI manual. In addition, the user is responsible to ensure that all product updates as
recommended by KMDSI have been performed.
3) Unauthorized modications have been made to the product.
4) The product has been abused or subjected to conditions which are unusual or exceed the
product’s intended service.
NOTE: Be sure to complete the enclosed warranty card and return it to KMDSI immediately. No
warranty claims will be honored without a satisfactorily completed warranty card on le at KMDSI.

Kirby Morgan®47
© ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #120614002 III
It is the responsibility of the owner of this product to register their ownership with Kirby Morgan Dive
Systems, Inc., by sending the warranty card provided. This card is to establish registration for any necessary
warranty work and provides a means of communication that allows KMDSI to contact the user regarding this
product. The user must notify KMDSI of any change of address by the user or sale of the product.
All changes or revisions to this manual must be recorded in this document to ensure that the manual
is up to date.
Record Of Changes
Change Number Date Description of Change
1 08/20/2008 Added: CE approval text to page 23 in chapter 2.
2 09/30/2008 Removed page number column on page number III.
Renumbered chapter 6 pages and subsequent chapters in table of contents.
REX®3 changed to REX®and image updated on page 14.
Added CE Certication text and logos on pages 19, 21 and 22.
Tables updated and moved to back on pages 23 and 24.
Renumbered Chapter 2 Sections
Image Updated page 28.
Updated Exploded view of REX®regulator on page 29.
Rearranged chapter 5 into 2 columns, pages 63.
Updated Image of special tools on page 64.
Updated text in chapter 6, 6.2.2 on page 65.
Updated Exploded view of REX® Exhaust System and changed REX®3 to REX®
on page 73.
Replaced Whisker Clamps with Tie Wraps on pages 74-76.
Rearranged and updated Chapter 7, 7.8.1, 7.10 on page’s 92-96. and
page’s 101-104, and 106-107.
Rearranged Appendix 1: Torque Specications on page 145-146.
Added Appendix A2 on page 143.
Added Appendix 3 on page 145.
3 11/05/2008 Added D-Ring to Image on page 18.
Blowapart Image Updated with D-Ring on page 32, 38, and 123.
Text Updated on pages 61-62.
Text Updated on page 120.
Added Microphone Diagram on page 134.
Image Updated on page 135.
Appendix A1: Torque Specications updated on page 141.
4 2/19/2009 Page 131 8.15.3 Removal of Communications Assembly added communications
breakage text.
Page 131 8.15.4 Replacement of Communications Assembly added communica-
tions breakage warning.

IV © ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #120614002
Kirby Morgan®47
5 3/30/2009 Page 74 Section 7.3.2 Step 3: Changed Picture caption, 270 kg. cm to 17 Newton
Meters.
Page 79 Section 7.4.4 Step 3 and 6: Changed 50 inch pounds to 35, 5.65 Newton
Meters to 4 and 40 inch pounds to 15.
Page 109 Section 8.4.2 Step 4: Changed 35 inch pounds to 20.
Page 118 Section 8.6.2 Step 14 and 16: Changed picture caption 16 kg.cm to 1.5
Newton Meters.
Page 120 Section 8.6.3 Step 9: Changed 16 kg. cm to 1.5 Newton Meters.
Page 123 Section 8.11.2 Step 3: Changed 35 inch pounds to 12 and 39 kg.cm to
1.3 Newton Meters.
Page 125 Section 35 inch pounds to 20 and 27 kg.cm to 2.25 Newton Meters.
Page 139 Torque Specications: Updated location numbers and added part # 555-
167 Bent Tube Assembly.
6 11/06/2009 Chapter 2 Addition of CE Conforming Criteria.
7 08/19/2010 Updated knob images and diagrams.
8 04/11/2011 Updated earphones throughout manual
9 06/17/2011 Changed 61 meters to 67 meters in Appendix 3 Table 3 Topside High-Pressure
Regulator Settings for use with the Kirby Morgan REX® Regulator
10 10/17/2011 Updated CE Identication Number to 2049 and corrected area code for Santa
Maria Ofce from 850 to 805 in Chapter 2
11 06/14/2012 Updated copyright format
Diving with compressed breathing gas is a hazardous activity. Even if you do everything
right there is always the potential for serious injury or death. No one piece of diving
equipment can prevent the possibility that you may be injured or killed any time you
enter the water. We do not herein make any effort to teach the principles of diving. The
information in this manual is intended for users of Kirby Morgan helmets and persons
that maintain or service Kirby Morgan helmets.
WARNING

Kirby Morgan®47
© ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #120614002 V
Table Of Contents
Warranty Information �������������������������������������������������������������������������������� II
Record Of Changes ���������������������������������������������������������������������������������III
Denition of Signal Words Used in this Manual �������������������������������������������������� X
Chapter 1 General Information KMDSI Products����������������������������������� 1
1.1 Introduction �������������������������������������������������������������������������������������� 1
1.2 Full-Face Masks and Manifolds���������������������������������������������������������������� 2
1.3 Kirby Morgan Diving Helmets ������������������������������������������������������������������ 4
Chapter 2 Description & Operational Specications Kirby Morgan 47 �� 9
2.1 CR Marking �������������������������������������������������������������������������������������� 9
2.2 CE Certication ���������������������������������������������������������������������������������� 9
2�2�1� CE Marking ��������������������������������������������������������������������������������� 9
2�2�2� Notied Body ������������������������������������������������������������������������������ 10
2.3 Other Marking ���������������������������������������������������������������������������������� 10
2.4 Product Specications������������������������������������������������������������������������� 10
2.5 Regulator Performance ������������������������������������������������������������������������ 10
2�5�1 REX®Regulator ����������������������������������������������������������������������������� 10
2�5�2 Minimum Operating Temperature ����������������������������������������������������������� 10
2.6 Cage Code �������������������������������������������������������������������������������������� 10
2.7 Operational Specications & ����������������������������������������������������������������� 10
2.8 Helmet Features �������������������������������������������������������������������������������� 11
2.9 General Description ���������������������������������������������������������������������������� 13
2�9�1 Helmet Shell �������������������������������������������������������������������������������� 13
2�9�2 Gas Flow Systems �������������������������������������������������������������������������� 13
2�9�3 Emergency Gas Supply System (EGS) ������������������������������������������������������ 16
2�9�4 Helmet Attachment to the Diver������������������������������������������������������������� 17
2�9�5 Sealing Arrangement ����������������������������������������������������������������������� 18
2�9�6 Reducing Carbon Dioxide ������������������������������������������������������������������ 19
2�9�7 Communications���������������������������������������������������������������������������� 19
2�9�8 Equalizing the Middle Ear ������������������������������������������������������������������� 19
2�9�9 Face Port or Viewing Lens ������������������������������������������������������������������ 19
2.10 Accessories ����������������������������������������������������������������������������������� 19
2�10�1 Eye Protection for Welding ���������������������������������������������������������������� 19
2�10�2 Special Regulator Tools for REX®Regulator ����������������������������������������������� 20
2.11 Helmet Transport And Storage �������������������������������������������������������������� 20
2�11�1 Helmet Carrying Bag ���������������������������������������������������������������������� 21
2.12 Use of Kirby Morgan Original Replacement Parts ����������������������������������������� 21
Chapter 3.0 Operating Instructions ����������������������������������������������������� 23
3.1 Introduction ������������������������������������������������������������������������������������� 23
3.2 Design Purpose��������������������������������������������������������������������������������� 23
3.3 First Use of Your Kirby Morgan Diving Helmet ���������������������������������������������� 25
3.4 Initial Adjustments to Your Helmet������������������������������������������������������������ 25
3�4�1 Head Cushion ������������������������������������������������������������������������������ 25
3�4�2 Trimming the Neck Dam �������������������������������������������������������������������� 25
3�4�3 Adjusting the Neck Pad��������������������������������������������������������������������� 26
3.5 Pre Dress-In Procedure ������������������������������������������������������������������������ 27
3�5�1 Pre-Dive Visual Inspection ������������������������������������������������������������������ 27

VI © ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #120614002
Kirby Morgan®47
3.6 Preparing the Helmet for Diving��������������������������������������������������������������� 28
3�6�1 Clean Face Port ���������������������������������������������������������������������������� 28
3�6�2 Check Moving Parts ������������������������������������������������������������������������ 28
3�6�3 Check Communications �������������������������������������������������������������������� 28
3�6�4 One Way Valve Check ���������������������������������������������������������������������� 28
3.7 Emergency Gas System (EGS) ���������������������������������������������������������������� 29
3.8 Setting Up to Dive ������������������������������������������������������������������������������ 34
3�8�1 Flushing Out the Umbilical ������������������������������������������������������������������ 34
3�8�2 Connecting the Umbilical to the Helmet ���������������������������������������������������� 34
3�8�3 Opening the Breathing Gas Supply to the Helmet������������������������������������������� 35
3�8�4 Fogging Prevention ������������������������������������������������������������������������� 35
3�8�5 Donning The Kirby Morgan Helmet ��������������������������������������������������������� 36
3�8�6 Testing the Breathing System ��������������������������������������������������������������� 39
3�8�7 Sealing Integrity Check ��������������������������������������������������������������������� 39
3�8�8 Adjust Regulator for Low Work Rates ������������������������������������������������������� 39
3.9 Removing the Helmet �������������������������������������������������������������������������� 40
3.10 Diving Procedures ���������������������������������������������������������������������������� 41
3�10�1 Standing By to Dive ����������������������������������������������������������������������� 41
3�10�2 Attaching the Umbilical to the Harness ���������������������������������������������������� 41
3�10�3 Diver Dons Helmet ������������������������������������������������������������������������ 41
3�10�4 Diver Check Gas Flow Systems ����������������������������������������������������������� 41
3�10�5 Communications Check ������������������������������������������������������������������� 41
3�10�6 Diver Ready ������������������������������������������������������������������������������� 41
3�10�7 Water Entry and Descent ������������������������������������������������������������������ 41
3.11 Emergency Procedures ���������������������������������������������������������������������� 42
3�11�1 Flooding ����������������������������������������������������������������������������������� 42
3�11�2 Inhalation Resistance���������������������������������������������������������������������� 42
3�11�3 Gas Flow Stops ��������������������������������������������������������������������������� 42
3�11�4 Demand Regulator Free Flow�������������������������������������������������������������� 43
3.12 Post Dive Procedures ������������������������������������������������������������������������ 44
3�12�1 Removing the Equipment������������������������������������������������������������������ 44
3�12�2 Removing the Helmet ��������������������������������������������������������������������� 44
3�12�3 Storage of the Helmet Between Dives ����������������������������������������������������� 44
Chapter 4 Troubleshooting������������������������������������������������������������������ 45
4.1 General ������������������������������������������������������������������������������������������ 45
4.2 Communication Malfunction ������������������������������������������������������������������ 45
4.3 One Way Valve Malfunction ������������������������������������������������������������������� 45
4.4 Side Valve Malfunction������������������������������������������������������������������������� 46
4.5 Water Leakage Into Helmet ������������������������������������������������������������������� 46
4.6 Demand Regulator Malfunction��������������������������������������������������������������� 47
4.7 Emergency Gas Supply Valve ����������������������������������������������������������������� 47
Chapter 5 Inspection and Maintenance ����������������������������������������������� 49
5.1 Routine Maintenance �������������������������������������������������������������������������� 49
5�1�1 Daily Pre-Dive Maintenance A2�3 ����������������������������������������������������������� 49
5�1�2 Daily Post Dive Maintenance A2�6 ���������������������������������������������������������� 49
5�1�3 Supervisors Equipment Checks A2�4 and A2�5 ��������������������������������������������� 49
5.2 Monthly Maintenance �������������������������������������������������������������������������� 49
5.3 Yearly Maintenance ���������������������������������������������������������������������������� 49
5�3�1 Overhaul/Inspection Checklist A2�1��������������������������������������������������������� 49

Kirby Morgan®47
© ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #120614002 VII
Chapter 6.0 General Preventative Maintenance ���������������������������������� 51
6.1 Introduction ������������������������������������������������������������������������������������� 51
6.2 Required tools, Sealing, Cleaning Agents, Lubrication ������������������������������������� 51
6�2�1 Component and Parts Cleaning������������������������������������������������������������� 52
6�2�2 Component and Parts Lubrication ���������������������������������������������������������� 52
6�2�3 Teon®Tape �������������������������������������������������������������������������������� 53
6�2�4 RTV Sealant �������������������������������������������������������������������������������� 53
6�2�5 Thread Locker ������������������������������������������������������������������������������ 53
6.3 General Cleaning & Inspection Procedures�������������������������������������������������� 53
6�3�1 O-ring Removal/Inspection/Cleaning and Lubrication��������������������������������������� 54
6.3.1.1 O-ring Removal��������������������������������������������������������������������������� 54
6.3.1.2 O-ring Inspection:������������������������������������������������������������������������� 54
6.3.1.3 O-ring Reuse: ���������������������������������������������������������������������������� 54
6.3.2 General Cleaning Guidelines ���������������������������������������������������������������� 54
6.3.2.1 Mild Soap Solution for General Cleaning and Leak Detector Use ������������������������������� 56
6.3.2.2 Acidic Cleaning Solution and Procedures ���������������������������������������������������� 56
6.3.2.3 Germicidal Cleaning Solutions and Procedure ������������������������������������������������ 56
6.4 Daily Maintenance������������������������������������������������������������������������������ 57
6.5 Monthly Maintenance (or between jobs) ����������������������������������������������������� 58
6�5�1 Locking Collar Assembly & Helmet Ring ���������������������������������������������������� 58
6�5�2 Neck Dam Ring Assembly ������������������������������������������������������������������ 58
6�5�3 Head Cushion and Chin Cushion ����������������������������������������������������������� 59
6�5�4 Communications Inspection ���������������������������������������������������������������� 59
6�5�5 Lubricate Nose Block O-Rings ������������������������������������������������������������� 59
6.6 REX®Demand Regulator & Exhaust System Post Dive Cleaning & Sanitizing ����������� 60
6�6�1 Post Dive Disassembly ��������������������������������������������������������������������� 60
6�6�2 Sanitizing ����������������������������������������������������������������������������������� 61
6�6�3 Post Dive Reassembly ���������������������������������������������������������������������� 62
Chapter 7.0 Breathing System Maintenance and Repairs �������������������� 63
7.1 Introduction ������������������������������������������������������������������������������������� 63
7.2 Torque Values ����������������������������������������������������������������������������������� 63
7.3 One Way Valve ���������������������������������������������������������������������������������� 63
7�3�1 Disassembly Of The One Way Valve �������������������������������������������������������� 63
7�3�2 Reassembly of the One Way Valve���������������������������������������������������������� 64
7.4 Side Block Assembly �������������������������������������������������������������������������� 66
7�4�1 General ������������������������������������������������������������������������������������� 66
7�4�2 Removal of the Bent Tube ������������������������������������������������������������������ 66
7�4�3 Separating the Side Block Assembly from the Helmet Shell �������������������������������� 66
7�4�4 Side Block Assembly Replacement �������������������������������������������������������� 68
7�5�2 Cleaning and Lubricating������������������������������������������������������������������� 70
7.5 Defogger Valve ��������������������������������������������������������������������������������� 71
7�5�1 Disassembly of the Defogger Valve ��������������������������������������������������������� 71
7�5�3 Reassembly of the Defogger Valve���������������������������������������������������������� 71
7.6 Emergency Valve Assembly ������������������������������������������������������������������� 72
7�6�1 Disassembly of the Emergency Valve ������������������������������������������������������� 72
7�6�2 Cleaning and Lubricating ������������������������������������������������������������������� 72
7�6�3 Reassembly of Emergency Valve ����������������������������������������������������������� 73
7.7 Bent Tube Assembly ��������������������������������������������������������������������������� 75
7�7�1 General ������������������������������������������������������������������������������������� 75

VIII © ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #120614002
Kirby Morgan®47
7�7�2 Removal of the Bent Tube Assembly�������������������������������������������������������� 75
7�7�3 Inspection of Bent Tube Assembly ���������������������������������������������������������� 76
7�7�4 Reinstallation of the Bent Tube Assembly ��������������������������������������������������� 76
7.8 Demand Regulator & Exhaust System Overhaul �������������������������������������������� 77
7�8�1 System Disassembly������������������������������������������������������������������������ 77
7.9 Cleaning REX®Regulator Parts ��������������������������������������������������������������� 82
7�9�1 Precautions for Cleaning�������������������������������������������������������������������� 82
7�9�2 Cleaning Instructions ����������������������������������������������������������������������� 82
7.10 REX®Regulator Re-Assembly ��������������������������������������������������������������� 84
7.11 Testing the REX®Demand Regulator for Proper Adjustment ����������������������������� 90
7�11�1 REX®Adjustment Troubleshooting��������������������������������������������������������� 90
7.12 Oral/Nasal Mask ������������������������������������������������������������������������������ 91
7�12�1 Oral/Nasal Removal ����������������������������������������������������������������������� 91
7�12�2 Inspection of Oral/Nasal ������������������������������������������������������������������� 91
7�12�3 Oral/Nasal Replacement������������������������������������������������������������������� 91
7.13 Reinstalling the Regulator on the Helmet��������������������������������������������������� 92
7.14 Overpressure Relief / Bleed Valve Overhaul Procedures ��������������������������������� 94
7�14�1 Overpressure Relief Valve ����������������������������������������������������������������� 94
7�14�2 Overpressure Relief Valve Disassembly and Cleaning ������������������������������������� 94
7�14�3 Overpressure Relief Valve Reassembly ���������������������������������������������������� 95
7�14�4 Overpressure Relief Valve Lift Check/Setting ���������������������������������������������� 95
Chapter 8 Corrective Maintenance������������������������������������������������������ 97
8.1 General ������������������������������������������������������������������������������������������ 97
8.2 Helmet Shell Inspection������������������������������������������������������������������������ 97
8.3 Nose Block Assembly�������������������������������������������������������������������������� 98
8�3�1 Nose Block Assembly Removal������������������������������������������������������������� 98
8�3�2 Nose Block Device Replacement ����������������������������������������������������������� 98
8.4 Handle and Weights���������������������������������������������������������������������������� 99
8�4�1 Handle Removal ��������������������������������������������������������������������������� 99
8�4�2 Handle Replacement ����������������������������������������������������������������������� 99
8�4�3 Side Weight Removal ��������������������������������������������������������������������� 100
8�4�4 Weight Replacement ��������������������������������������������������������������������� 101
8�4�5 Top Weight Removal ��������������������������������������������������������������������� 101
8�4�6 Top Weight Replacement ����������������������������������������������������������������� 101
8.5 Face Port�������������������������������������������������������������������������������������� 102
8�5�1 General ����������������������������������������������������������������������������������� 102
8�5�2 Face Port, Port Retainer, and Nose Block Device Removal ������������������������������� 102
8�5�3 Face Port, Port Retainer and Nose Block Replacement����������������������������������� 103
8�5�4 Special Note Regarding Ports ������������������������������������������������������������ 105
8�5�5 Port Retainer������������������������������������������������������������������������������ 105
8.6 Neck Dam ������������������������������������������������������������������������������������ 106
8�6�1 Removal of the Neck Dam ���������������������������������������������������������������� 106
8�6�2 Neoprene Neck Dam Replacement ������������������������������������������������������� 106
8�6�3 Latex Neck Dam Replacement������������������������������������������������������������ 109
8�6�4 Trimming a Latex Neck Seal �������������������������������������������������������������� 110
8.7 Neck Dam Pull Strap ������������������������������������������������������������������������� 111
8�7�1 Neck Dam Pull Strap Removal ������������������������������������������������������������ 111
8�7�2 Neck Dam Pull Strap Replacement ������������������������������������������������������� 111
8.8 Chin Strap������������������������������������������������������������������������������������� 111
8�8�1 Chin Strap Removal ���������������������������������������������������������������������� 111

Kirby Morgan®47
© ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #120614002 IX
8�8�2 Chin Strap Replacement������������������������������������������������������������������ 111
8.9 O-Ring Seal Replacement ������������������������������������������������������������������ 112
8.10 Helmet Ring ��������������������������������������������������������������������������������� 113
8�10�1 Helmet Ring Repairs��������������������������������������������������������������������� 113
8.11 Sealed Pull Pins ����������������������������������������������������������������������������� 113
8�11�1 Removal of Sealed Pull Pins������������������������������������������������������������� 113
8�11�2 Replacement of Sealed Pull Pins �������������������������������������������������������� 113
8.12 Swing Tongue Catch ����������������������������������������������������������������������� 114
8�12�1 Disassembly of the Swing Tongue Catch ������������������������������������������������ 114
8�12�2 Reassembly of the Swing Tongue Catch������������������������������������������������� 115
8.13 Locking Collar ������������������������������������������������������������������������������� 116
8�13�1 Locking Collar Removal ����������������������������������������������������������������� 116
8�13�2 Locking Collar Disassembly������������������������������������������������������������� 117
8�13�3 Locking Collar Reassembly ������������������������������������������������������������� 118
8.14 Head Cushion and Chin Cushion���������������������������������������������������������� 119
8�14�1 Head Cushion Foam��������������������������������������������������������������������� 119
8�14�2 Chin Cushion Foam ��������������������������������������������������������������������� 119
8.15 Communications System������������������������������������������������������������������� 120
8�15�1 General���������������������������������������������������������������������������������� 120
8�15�2 Earphone Inspection �������������������������������������������������������������������� 120
8�15�3 Removal of Communications Assembly ������������������������������������������������� 121
8�15�4 Replacement of Communications Assembly��������������������������������������������� 121
8�15�5 Microphone Replacement ��������������������������������������������������������������� 121
8�15�6 Earphone And Wire Assembly Replacement��������������������������������������������� 122
8�15�7 Waterproof Connector������������������������������������������������������������������� 123
8.15.7.1 Connector Removal�������������������������������������������������������������������� 123
8.15.7.2 Connector Replacement���������������������������������������������������������������� 123
8�15�8 Terminal Connections in the Waterproof Connector ������������������������������������� 123
8�15�9 Communications Posts ����������������������������������������������������������������� 125
8.15.9.1 Communications Post Removal ��������������������������������������������������������� 125
8.15.9.2 Communications Post Replacement ����������������������������������������������������� 125
Chapter 9.0 Accessories for the Kirby Morgan 47 ����������������������������� 127
9.1 Introduction ����������������������������������������������������������������������������������� 127
9.2 Low Pressure Inator Hose������������������������������������������������������������������ 127
9�2�1 Installation of the Low Pressure Inator Hose ��������������������������������������������� 127
9�3�1 Weld Lens Assembly Installation ���������������������������������������������������������� 128
9.5 Use of Quick Disconnect �������������������������������������������������������������������� 129
9.4 Weld Shield Assembly ����������������������������������������������������������������������� 129
9�4�1 Weld Shield Assembly Installation �������������������������������������������������������� 129
Table of Equivalents�������������������������������������������������������������������������� 131
Appendix 1: Torque Specications ���������������������������������������������������� 132
Note on Torque Specications ���������������������������������������������������������� 133
Checklist, Maintenance, and Pre-Dive Inspections ������������������������������������������� 133
Appendix A2 Maintenance and Inspection Procedures ���������������������� 134
Appendix 3 Supply Pressure Requirements & Tables ������������������������� 136
Appendix 3 Table 1 Work Rate Expressed as Respiratory Minute Volume (RMV)* ��������� 137
Appendix 3 Table 2 REX®Regulator Low-Pressure Compressor Supply Pressure
Requirements Table Continued* ���������������������������������������������������������������� 138
Appendix 3 Table 3 Topside High-Pressure Regulator Settings for use with the Kirby

X © ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #120614002
Kirby Morgan®47
CAUTION
For your protection, pay particular attention to items identied by signal words in this manual. These terms are identied
as, CAUTION, WARNING AND DANGER. It is especially important for you to read and understand these sections.
This word indicates an imminently hazardous situation, which if not avoided, could re-
sult in death or serious injury.
This word indicates a potentially hazardous situation, which, if not avoided, could result
in death or serious injury.
This word indicates a potentially hazardous situation, which if not avoided, may result in
minor or moderate injury. It may also be used to alert against unsafe practices.
If English is not your native language and you have any difculty understanding the language of any warnings as they
appear in the manual, please have them translated.
Este é um aviso importante. Queira mandá-lo traduzir.
Este es un aviso importante. Sirvase mandario traducir.
Quest è un avviso importante. Tradurlo.
Ceci est important. Veuillez traduire.
Diese Mitteilung ist wichtig. Bitte übersetzen lassen.
If you have any questions concerning this manual or the operation of your helmet, contact KMDSI (805) 928-7772 or
IMPORTANT: A word about this manual. We have tried to make this manual as comprehensive and factual
as possible. We reserve the right, however, to make changes at any time, without notice, in prices, colors, materials,
equipment, specications, models and availability. Since some information may have been updated since the time of
printing, please contact your local KMDSI dealer if you have any questions. To nd a dealer near you, please see the
Kirby Morgan web site, www.kirbymorgan.com. Periodically KMDSI Operations and Maintenance Manuals are re-
viewed. Any updates/changes will be posted on the KMDSI website and may be downloaded for insertion/correction.
Important Safety Information:
This Kirby Morgan diving helmet is intended for use by trained divers who have successfully completed a recognized
training course in surface supplied diving.
Definition of Signal Words Used in this Manual
DANGER
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING

Kirby Morgan®47
© ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #120614002 XI
WARNING
Follow all the instructions in this manual carefully and heed all safety precautions. Im-
proper use of this diving helmet could result in serious injury or death.
Kirby Morgan Dive Systems, Inc. (KMDSI) warns all divers who use Kirby Morgan diving
helmets or masks to be sure to use only KMDSI original parts from a KMDSI authorized
dealer. Although other parts, O-rings and fittings may appear to fit your Kirby Morgan
diving helmet or mask, they may not be manufactured to the same standards maintained
by KMDSI.The use of any parts other than KMDSI original parts may lead to equipment
failure and accidents.
Diving in waters that are chemically, biologically, or radiologically contaminated is ex-
tremely hazardous. Although Kirby Morgan diving helmets may be adapted for use in
some contaminated environments, special training, equipment, and procedures are
necessary. Do not dive in a contaminated environment unless you have been thoroughly
trained and equipped for this type of diving.
Read this manual before using or maintaining the helmet, even if you have experience with other diving helmets. If
you have purchased the helmet new from a dealer, be sure to send in the warranty registration card so we may
keep you informed of any safety notices that affect this product. If you resell or loan this helmet to another diver,
be sure this manual accompanies the helmet and that the person reads and understands the manual. In addition to the
manual a log book should be used to log all repairs, maintenance and use.
Diving is a life threatening occupation. Even if you do everything right you can still be
killed or injured. None of the models of Kirby Morgan helmets or masks can prevent ac-
cidents, injuries or death due to improper training, poor-health, improper supervision,
improper job requirements, improper maintenance or acts of God.
This helmet was completely checked and should be ready to dive as it was shipped from
the factory. However, it is always the diver’s responsibility to check all the components
of the helmet prior to diving.
WARNING
WARNING
WARNING
WARNING
WARNING
This manual is supplied to the original purchaser of this helmet. If you have any questions about the use of the helmet
or you need another copy of this manual, contact KMDSI or your nearest KMDSI dealer. It may also be downloaded
free from the KMDSI website at www.KirbyMorgan.com.
Any and all fiberglass repairs done to this helmet MUST be done by a KMDSI factory
trained repair facility. Painting is not recommended by KMDSI. Furthermore, many diving
companies will not allow painted helmets to be used because painting can mask previ-
ous fiberglass damage. KMDSI certified technicians are not responsible for certifying
helmets free from damage during annual overhauls.
Helmet shells can be re-gel coated by authorized/certified KMDSI trained technicians
that have received fiberglass training by KMDSI. Helmets that are to be painted for cos-
metic purposes, should be first, certified free of fiberglass damage by an authorized
KMDSI technician certified in fiberglass repair. A log entry should be made in the hel-
met log that the helmet was free of damage prior to painting. Keep in mind other KMDSI
technicians can refuse to work on helmet shells that have previously been painted or
repaired by non KMDSI certified persons.

XII © ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #120614002
Kirby Morgan®47
WARNING
WARNING
WARNING
WARNING
WARNING
If you have any questions regarding the use, maintenance, or operation of this helmet, contact KMDSI at (805) 928-
7772, fax: (805) 928-0342, or e-mail: [email protected].
Kirby Morgan masks and helmets are cleaned and lubricated for oxygen ser-
vice when they come from the factory. However, if the helmet is used with an
oil lubricated air compressor, contamination with hydrocarbons may result.
If the breathing system in the helmet is exposed to hydrocarbons, it must be
cleaned for oxygen service and lubricated with oxygen safe lubricants before
using it again with breathing mixtures containing a high percentage of oxy-
gen. If this is not done, res and explosions may result, exposing the user to
serious personal injury or death.
Components requiring lubrication, should only be lubricated with oxygen compatible lubricants such as Christo
Lube®, Fluorolube®, or Krytox®. Lubricants must be used sparingly and should not be mixed with other lubricants.
KMDSI helmets and masks are intended for underwater use only and should only be
used by qualified divers that have received proper training in the use of this type of
equipment. KMDSI helmets and masks should not be used or worn without the appro-
priate life support systems, such as air or gas supplies and support personnel as de-
scribed in this manual.
KMDSI helmets and masks should never be used for motor sport racing, aviation /
space craft use, or for chemical warfare use. The helmet must never be used by persons
in poor physical condition, by persons with previous head, neck, or back injuries which
could be aggravated by its use. The helmet should not be used by persons under the in-
fluence of drugs or alcohol. Furthermore, infants, children, or persons under the age of
18 should never wear KMDSI helmets and masks. Failure to pay heed to the above could
result in serious injury or death.
Never use the helmet without first completing all pre-dive maintenance and set up pro-
cedures.
Do not use KMDSI masks or helmets in currents exceeding 3.0 knots Use in currents
greater than 3 knots may allow water to enter the exhaust valve, possibly causing regu-
lator flooding.
Surface-supplied diving can be a strenuous activity. The Kirby Morgan 47 weighs ap-
proximately 30 lbs. KMDSI recommends that persons with a previous neck or back
injury seek professional medical approval prior to engaging in surface supplied diving
operations using the Kirby Morgan 47. Use of the Kirby Morgan 47 with a pre-existing
physical/medical condition may result in death or serious injury.
The information contained in this manual is intended to aid the user in optimizing the performance of this helmet.
The application of some of this information will depend on the diving situation and the use of associated equipment.
Many countries have specic laws and rules regarding commercial diving. It is important for the user to understand
the rules, regulations, and philosophy imposed by the governing, regulating bodies whenever using commercial diving
equipment.

Kirby Morgan®47
© ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #120614002 XIII
Whenever KMDSI helmets or masks are used in European Countries, which have adopted the C.E. certication pro-
grams, they must only be used with C.E. certied components. Diving operations should only be conducted within the
limits of the operational specications, and in accordance with the rules and regulations established by the governing
authority in the specic country or geographical location where the diving operations are being conducted. If you have
any questions concerning this manual or the operation of your helmet, contact KMDSI (805) 928-7772 or at kmdsi@
WARNING
Always read the Material Safety Data Sheet (MSDS) for any chemical - adhesive, clean-
ing agent, or lubricant - used on your Kirby Morgan helmet. Some of these chemicals
may cause serious bodily injury or death if used improperly or without the proper per-
sonal protective equipment.

XIV © ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #120614002
Kirby Morgan®47
C
O
M
M
E
R
C
I
A
L
L
Y
R
A
T
E
D
-
P
R
O
F
E
S
S
I
O
N
A
L
D
I
V
I
N
G
G
E
A
R
-
D
I
V
E
L
A
B
T
E
S
T
E
D
™
The Kirby Morgan®47 helmet
Defog Free Flow
Valve Knob
Regulator Adjustment
Knob
Equalization Device
Oral Nasal Mask
Port Retainer
Handle
Purge Button
Helmet Shell
Communications
Module
REX®Exhaust
System
Sideblock
EGS Valve
Pull Pin
Non-Return Valve

Kirby Morgan®47
© ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #120614002 1
This manual will refer to location numbers in specic drawings, or in the exploded view, which is
in the back of this manual. These numbers are called “location” numbers. They are used to nd
the referred to parts in the drawings in this manual only. They are not the part number. Next to
the exploded drawing is a list of the “location” numbers that match the Kirby Morgan part num-
bers along with the name of the part. Always check the part number when ordering to make sure
it is correct. When ordering, always specify the helmet model number and serial number as well.
The Kirby Morgan Corporation was started in 1965.
The copper and brass “Heavy Gear” or “Standard
Dress” helmets were the rst helmets manufactured by
the company. Over the years Kirby Morgan designed,
manufactured and sold many different helmets and
masks for commercial divers.
Staying active in commercial diving has contributed to
the successful design innovations of KMDSI products.
This may be the primary reason for the acceptance of
our designs by professional divers.
Bev Morgan has designed more than fty-seven div-
ing helmets and over 40 diving masks. All employees
of KMDSI participate as part of the Kirby Morgan
design team. It would not be possible for us to supply
the commercial, military, scientic, and public service
diving industries with our equipment, without the team
of people that make up Kirby Morgan Dive Systems,
Inc. (KMDSI)
We feel it is important for the reader to understand
that we at KMDSI consider ourselves as only part
of the process along the path in diving equipment
design. We welcome all input from our customers.
The thinking of many good divers, diving equipment
engineers, diving medical specialists, diving organiza-
tion administrators and their supporting personnel has
contributed to the current state of the art of diving.
Each piece of gear we manufacture has in it some of
the thinking of those who have gone before us. To
all those people who gave something of themselves
to the men and women who work underwater, we
express a thank you.
We have a strong commitment to providing the best
diving equipment and service possible. This thinking
has been the policy of Kirby Morgan Dive Systems,
Inc. and we will continue to take this approach to
our work.
Our extensive dealer network makes it easy to obtain
genuine Kirby Morgan replacement parts, as well as
technical assistance worldwide.
KMDSI has always concentrated on designing and
manufacturing diving equipment that allows most
repairs, inspections, and all routine maintenance to
be performed by the user. Most routine preventative
and corrective maintenance can be accomplished by
the user utilizing this manual, the KMDSI Tool Kit
(P/N 525-620) and common hand tools. Technician
training is available through Dive Lab Inc. Informa-
tion can be obtained on line at www.divelab.com or
by telephone at 850-235-2715.
Chapter 1
General Information KMDSI Products
1.1 Introduction
Bev Morgan, Chairman of the Board
Kirby Morgan Dive Systems, Inc.
STOP!
BEFORE GOING FURTHER-

2 © ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #120614002
Kirby Morgan®47
The EXO Full Face Mask is designed for both
surface supplied and scuba diving. By enclosing the
divers eyes, nose and mouth, the EXO permits nearly
normal speech when used in conjunction with most
wireless, and all hard wire underwater communica-
tion systems.
The EXO BR (BALANCED REGULATOR) shown
here is designed to meet or exceed recommended
performance goals in both scuba and surface supplied
modes and is approved. It meets and surpasses
European standards for regulator performance.
The Balanced Regulator helps reduce the work of
breathing for the diver by balancing the intermediate
air pressure against the valve sealing pressure inside
the regulator. This enables the regulator to instantly
adjust to changes in line pressure. The balanced
regulator is adjustable for a wide range of intermedi-
ate pressures between 90 PSIG – 250 over ambient
pressure (6.2 – 17 bar).
Both models have a modular communications de-
sign that permits rapid and simple maintenance. The
optional Hard Shell provides surfaces for mounting
lights, cameras etc.
KMB®18 A/B
The KMB 18B Band Mask frame is constructed of
hand laid berglass. The head harness is a molded,
strong tear resistant neoprene rubber.
The hood, which attaches to the mask frame with
welded stainless steel bands, provides warmth for the
divers head as well as pockets for the earphones. The
communications connections can be either a male
waterproof plug in type or bare wire posts. Both this
mask and the KMB 28B feature the new Tri-Valve™
Exhaust System.
The KMB 28B Band Mask (not shown) is very simi-
lar to the KMB 18, with many parts on the KMB 18B
being interchangeable with the KMB 28B. The major
difference between the 18 and 28 is the material of the
mask frame itself. The KMB 18 has a berglass frame
(yellow) while the KMB 28B frame is an extremely
durable injection molded plastic (black).
Other differences include:
1) The main exhaust body of the KMB 28 is part of the
frame itself and uses a #545-041 main exhaust cover
2) no comfort insert is required on the 28
3) the face ports for the 18 and the 28 differ slightly
in size.
Both the KMB 18 and KMB 28 are approved.
C
O
M
M
E
R
C
I
A
L
L
Y
R
A
T
E
D
-
P
R
O
F
E
S
S
I
O
N
A
L
D
I
V
I
N
G
G
E
A
R
-
D
I
V
E
L
A
B
T
E
S
T
E
D
™
EXO®BR
C
O
M
M
E
R
C
I
A
L
L
Y
R
A
T
E
D
-
P
R
O
F
E
S
S
I
O
N
A
L
D
I
V
I
N
G
G
E
A
R
-
D
I
V
E
L
A
B
T
E
S
T
E
D
™
1.2 Full-Face Masks and Manifolds
approved and
™
marked
approved and
™
marked

Kirby Morgan®47
© ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #120614002 3
The SuperMask M-48 is an innovative new design
in a full-face mask. It provides the diver with all the
comfort of a full-face mask with the convenience of
changeable second stage regulators as well as the abil-
ity to use a snorkel without having to remove the mask.
The mask is comprised of two major components,
the mask frame and the interchangeable lower pod.
The removable lower pod is a feature unique to the
SuperMask full-face mask. When diving, the pod is
easily removed and replaced on the mask, providing
the diver the capability to buddy-breathe, snorkel, use
an octopus or perform an “in water” gas switch.
With the pod sealed to the mask, the exible, silicone
pod cover allows the diver to quickly place the regula-
tor mouthpiece into the mouth or dive with it free of
the mouth for communications. With the mouthpiece
in, the regulator may be used without the pod being
sealed to the mask.
The mask may also be used surface supplied when
used with the proper accessories. We are currently
developing several different pod congurations for
both open circuit and rebreather use. For further
information, see the Frequently Asked Questions
(FAQ) area on
our web site at www.KirbyMorgan.
com/FullFaceMasks/M48.html.
The Kirby Morgan Air Control System-5 (KMACS)
is a lightweight, portable control box for use in sur-
face supplied air diving operations. The KMACS-5
controls the diver’s air supply, communications and
monitors the diver’s depth. It allows two divers clear
push-to-talk (two wire) or round robin (four wire)
communications. The KMACS-5 is also available
without communications.
The air supply can be either from a low-pressure
compressor or high-pressure cylinders. The adjustable
rst stage regulator reduces the high-pressure air and
supplies low pressure through the umbilical to the
diver’s breathing system.
High pressure yokes permit U.S. standard scuba cyl-
inders or DIN equipped cylinders to be used. Low-
pressure air supply ttings allow for a compressor to
be used as the primary air source.
A complete pneumo system with dual reading gauges
(both US Standard and Metric) is provided for each
diver’s air, as well as a shut-off/bleed system that uses
two high-pressure feed lines which allows changing
of used cylinders without interruption of the diving
operation. Optional shut off valves allow the isolation
of each diver’s air supply.
The Communication Set is a multipurpose intercom-
munication system that provides reliable and clear
communications between a topside operator (tender)
and one or more surface-supported divers, recompres-
sion chambers, or other submersible systems.
KMACS-5
w/ No Communications
KMACS-5
w/ Communications
approved and
™
marked
SuperMask M-48
w/ Scuba Pod
SuperMask M-48
w/ Rebreather pod
C
O
M
M
E
R
C
I
A
L
L
Y
R
A
T
E
D
-
P
R
O
F
E
S
S
I
O
N
A
L
D
I
V
I
N
G
G
E
A
R
-
D
I
V
E
L
A
B
T
E
S
T
E
D
™
C
O
M
M
E
R
C
I
A
L
L
Y
R
A
T
E
D
-
P
R
O
F
E
S
S
I
O
N
A
L
D
I
V
I
N
G
G
E
A
R
-
D
I
V
E
L
A
B
T
E
S
T
E
D
™
™
marked

4 © ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #120614002
Kirby Morgan®47
1.3 Kirby Morgan Diving Helmets
All Kirby Morgan diving helmets and masks are
manufactured by Kirby Morgan Dive Systems, Inc.
(KMDSI). Each step of the manufacturing process is
carefully controlled to assure the customer of a high
quality, durable helmet that will function properly for
many years.
There are eight models of Kirby Morgan diving hel-
mets currently in production. They are the SuperLite®-
17B, (MK-21- U.S. Navy version), SuperLite® 17C the
SuperLite® 27, and Kirby Morgan models 37, 37SS,
47, 57, and 77. All are ™ marked.
The SuperLite®-17 A/B was rst developed in 1975
and quickly set a new standard for diving helmet
design. Many large and small commercial diving
companies, military organizations, scientic divers,
and public safety divers are successfully using this
design around the world. This helmet is marked.
The SL-17 A/B helmet system consists primarily of
two major components: the neck dam/yoke assembly,
and the helmet. To don the helmet, the diver rst slips
the angled neck dam with the attached yoke over their
head. The helmet is lowered onto the diver’s head
with the help of a tender, then the yoke hinge tab is
hooked onto the alignment screw on the rear weight.
The neck clamp is then slipped onto the helmet and
locked. The locking system not only seals the neck
dam to the helmet but also secures the front of the
yoke, fastening the helmet to the diver’s head.
The SuperLite®-17A / B shares many common breath-
ing system parts with all Kirby Morgan helmets
and masks. The breathing system was man-tested
to 1600 FSW by the University of Pennsylvania and
approved by the U.S. Navy for surface-supplied div-
ing to 190 FSW with air and 300 FSW with mixed
gas. It surpasses all requirements of all governing
agencies and it is approved for commercial diving
through out the world.
SuperLite®17A/B Kirby Morgan®37
Yoke and Latch Catch
Assembly
Neck Pad and
Sealed Pull Pins.
C
O
M
M
E
R
C
I
A
L
L
Y
R
A
T
E
D
-
P
R
O
F
E
S
S
I
O
N
A
L
D
I
V
I
N
G
G
E
A
R
-
D
I
V
E
L
A
B
T
E
S
T
E
D
™
approved and
™
marked approved and
™
marked

Kirby Morgan®47
© ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #120614002 5
Other features that are common to all Kirby Morgan
helmets include:
* Face port and retainer ring
* Communications components
* Oral/nasal mask
* Nose block device
* Air train defogger
The Kirby Morgan®37 Commercial Diver’s Helmet
represents what we at Kirby Morgan consider to be
a turning point in modern diving helmet design. The
helmet consists of two major assemblies: the helmet
shell/helmet ring assembly and the neck dam/neck
ring assembly.
The helmet comes with the large tube SuperFlow®
350 adjustable demand regulator which provides an
easier breathing gas ow during peak work output.
A quick change communications module is available
with either bare wire posts or a waterproof connector.
The helmet ring houses the sealed pull pins and
provides protection for the bottom end of the helmet.
The diver is also provided with an internally adjust-
able chin support. This custom t and balance seats
the helmet comfortably for long periods of time even
when working in the face down position.
The SuperLite®27® Commercial Diver’s Helmet has
all the same features of the KM37 on a smaller, low
volume shell design. This helmet is often preferred
by persons with smaller heads.
The chrome plated machined brass helmet neck ring
houses the sealed pull pins and provides protection
for the bottom end of the helmet. Like the SL-17K,
37 and 17C, the diver is provided with an internally
adjustable chin support. This support, along with the
adjustable neck pad on the locking collar, gives the
diver a comfortable, secure, custom t.
The quick-change communications module, available
with either bare wire posts or a waterproof connector,
allows for easy, efcient maintenance of the helmets
communications.
The helmet also features the SuperFlow® 350 large
tube adjustable demand regulator. The helmet is
available in the umbilical over the shoulder, “B”
conguration only.
SuperLite®27®
C
O
M
M
E
R
C
I
A
L
L
Y
R
A
T
E
D
-
P
R
O
F
E
S
S
I
O
N
A
L
D
I
V
I
N
G
G
E
A
R
-
D
I
V
E
L
A
B
T
E
S
T
E
D
™
The Kirby Morgan®47 offers the ultimate in a high
performance breathing regulator. This helmet has an
entirely new breathing system, oral nasal mask, and
water ejection system. The REX® Demand Valve, with
it’s fully adjustable balanced piston is a breakthrough
design that exceeds the requirements of all govern-
ment or other testing agencies.
It has the best work-of-breathing performance when
compared to ANY other commercial diving helmet.
The Kirby Morgan 47 Dive Helmet has been tested
and meets or exceeds European CE requirements and
is fully commercially rated. In all other respects, this
helmet is nearly identical to the Kirby Morgan 37.
C
O
M
M
E
R
C
I
A
L
L
Y
R
A
T
E
D
-
P
R
O
F
E
S
S
I
O
N
A
L
D
I
V
I
N
G
G
E
A
R
-
D
I
V
E
L
A
B
T
E
S
T
E
D
™
®
Kirby Morgan®47
approved and
™
marked
approved and
™
marked

6 © ⅯⅯⅩⅡ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #120614002
Kirby Morgan®47
The Kirby Morgan®77 represents the rst in a new
generation of stainless steel diving helmets that pro-
vide an alternative for the diver who prefers a metal
helmet. The helmet features a stainless steel version
of our new REX® regulator, which offers the best
performance of any Kirby Morgan system.
It has the best work-of-breathing performance when
compared to ANY other commercial diving helmet.
The Kirby Morgan 77 Dive Helmet has been tested
and meets or exceeds European CE requirements and
is fully commercially rated.
The advantages of this all stainless steel helmet in-
clude the following:
• No renishing required if the surface is scratched
or gouged.
• Faster production of helmets for customer delivery.
• Elimination of threaded inserts for securing the port
retainer to the helmet shell.
• No need to remove the handle to remove the port
retainer.
• One piece sideblock includes both the free-ow valve
and the Emergency Gas System valve.
• The helmet ring is an integral part of the helmet.
®
The Kirby Morgan®57 helmet features our revo-
lutionary new SuperFlow® 450 Stainless Balanced
Regulator. It's machined from a stainless steel casting
for the ultimate in performance and reliability.
Like all KMDSI regulators on our helmets and
Band Masks®, we use only regulators that are speci-
cally designed for surface-supplied diving, that will
perform over the wide range of pressures delivered
by low pressure compressors. An ordinary SCUBA
regulator mounted on a diving helmet is not capable
of delivering the gas you need at heavy work loads.
This commercially rated fully diver adjustable regu-
lator delivers all the breathing gas you might require
for the most demanding work underwater.
The Kirby Morgan®57 also includes our Quad
Valve™ Exhaust System. It's recommended for div-
ing in biologically contaminated water, when you're
properly trained and equipped, using recommended
procedures. This new exhaust has exceptionally low
exhalation resistance that you must experience to
appreciate.
®
C
O
M
M
E
R
C
I
A
L
L
Y
R
A
T
E
D
-
P
R
O
F
E
S
S
I
O
N
A
L
D
I
V
I
N
G
G
E
A
R
-
D
I
V
E
L
A
B
T
E
S
T
E
D
™
™
marked
approved and
™
marked
BWARNING
Before attempting any diving in any
type of contaminated water, a com-
plete diving and topside course in
hazardous materials emergencies
should be completed. The divers and
the topside team must be properly
trained and have the proper safety
equipment. All helmets and suits can
leak water under certain conditions.
Divers should use extreme caution
when diving in contaminated waters.
Other manuals for 47
1
Table of contents
Other Kirby Morgan Motorcycle Accessories manuals