KiSS MC-750 User manual

MC-750
Rechargeable Pet Clipper
Owner’s Guide
PROFESSIONAL
CLIPPER
Cutting head
Adjustment lock
Adjusting knob
Adjusting RPM
ON/OFF switch
LCD screen
Oil BottleCleaning Brush
To ensure you achieve the best possible use of your clipper please read
the following instructions.
Charging time：2 hours
Operation time：5 hours
Blade width：44.5 mm
Dimensions：177(H)×45(W)×48(D)mm
Weight：221 grams
Specifications
Component Name
Accessories
1
Adapter
LCD Screen
Power off
Motor RPM
use time
Motor RPM
use time
Motor RPM
use time
Starting icon
Low battery
Low
Battery
Charging process
Full charge
FULL
TURBO
1.3mm
1.6mm
1.9mm
300
min
Motor
6000
RPM
270
min
Motor
7000
RPM
240
min
RPM
Comb

4. Charging indicator “ ”can be seen on LCD.
5. It will automatically stop after a full charge and the icon “ ” can be seen on LCD.
6. A full charging takes an estimated 2 hours. The battery function will be at full
capacity after three charges.
SAFETY CAUTIONS
IMPORTANT NOTICE
OPERATING INSTRUCTIONS
1. Use this appliance for its intended purpose. Use only on clean, dry hair.
2. Close supervision is necessary when this appliance is by or near children.
3. Use only with accessories included in the package, or those recommended by
the manufacturer.
4. Avoid contact with the eye area. Avoid use near or on open wounds, damaged or
sensitive skin.
5. Except when charging, always unplug from the electrical socket after use.
6. Keep away from water and all liquids and any detergent agents.
7. Do not pull, twist or wrap the cord tightly. Pull on the plug (not the cord) to remove
from power receptacle.
8. Charging should be done in a safe environment; indoors in a dry place.
9. The charger adaptor must be kept dry at all times.
1. The blade, main unit, power cord or attachment comb is damaged.
2. The clipper or the adapter is dropped into water.
3. The clipper is switched off, but the charging indicator does not light up when
plugged into the power source.
The clipper and accessories must be checked regularly to prevent damage and
ensure good performance.
If damage is detected, do not put the device into operation.
1. The blade must be lubricated before and after each use. This will maintain good
condition and will extend its service life.
2. Nonstop usage for hours may cause overheating of blades, reducing the cutting
performance and shortening their life. Should the blades overheat, switch the unit
off for a few minutes to let it cool down; then lubricate the blades.
3. Hair must be clean and dry before cutting. Foreign matter hidden in the hair may
damage the blade edge.
4. Hair may gather inside the blade housing during use. Too much stored hair will
reduce the oscillating ability of the blades and cause malfunctioning. Always
clean away hair in the blade housing before and after each use.
5. Avoid impact of the blade with hard objects as this may cause damage to the
blade teeth.
1. Do not overcharge. It takes 2 hours to charge your trimmer. Charging over 36
hours may shorten the life of the battery.
2.The life of the battery will be shortened if the trimmer remains at less than full charge
for long periods. Charge unused clippers every 3 months to activate the battery.
3. It is normal for the adapter and the internal parts to become warm when charging.
1. Use or store the trimmer only at room temperature.Avoid direct sunlight, moisture
or heated surfaces and environments.
Operating range 0 - 40℃.
2. Do not attempt to unscrew any part of the trimmer.
1. Icon “Low battery ” can be seen on LCD screen to remind you the clipper is charging.
2. Connect the charging cord to the charging slot at one end of clipper.
3. Confirm that the switch is off and insert the plug.
Should the following situations occur, unplug and switch off immediately,
and send for examination or repair.
Always switch off before removing, replacing and cleaning the blade.
Recharging time: 2 hours
Cordless operation time: 1.5 hours (5000RPM)
The blade length adjuster is on the clipper.
Select the desired length of the blade by moving the adjustment slide.
The “Low battery ” icon will twinkle when the available time is left is approximately
15 minute.
Set dial to 1.9mm to reassemble blade; otherwise the adjuster does not work.
This trimmer can be operated by plugging it into the power source when the
battery is not fully charged.
1. Switch off.
2. Connect the adapter to the wall socket.
3. Connect the DC plug to the clipper.
4. Check if the charging indicator is lit.
5. Switch “On” to operate.
* Except for the purpose of charging, always switch off and unplug the adapter
from the wall socket after use.
* Do not frequently use the clipper plugged without having recharged the battery,
as this may reduce the life of the battery.
* Charge at room temperature between 5℃and 35℃.
1. Remove the blade set from the blade housing by pressing the top cutting head
with your thumb.
2. Brush off the collected residual hair from between the teeth and the blade housing.
3. Move the oscillating bracket with your thumb to separate stored hair from the
blades. Brush off the hair between the blades. Make sure that hair is not trapped
between the blades.
Lubricate both friction surfaces of the front cutting teeth and the hind supporting areas.
1. Hind supporting areas: push the oscillating part to one side: lubricate the visible
friction surface on the other side. Drop a small amount of oil on both sides.
2. Front cutting teeth: Drop a small amount of oil on the blade teeth and spread evenly.
Slightly move the oscillating part to spread the oil between the blades.
1. Set dial to 1.9mm to reassemble blade.
2. To replace the blade set, put the bottom of the blade set clip into the blade set
mount on the blade housing.
3. Push until snaps into place.
1. Switch off and unplug the trimmer before cleaning
2. Wipe with a soft damp cloth.
3. Allow it to completely air dry before use.
Keep The Clipper Away From Moisture; Do Not Submerge In Water Or Liquid.
MAINTENANCE
Removing and Cleaning the Blade
Lubricating the Blade
Replace the Blade
Cleaning the Main Body and Accessories
Caution
Battery Condition Indicator
Blade Adjustment
Cord Operation
Blade
Battery
Others
Changing
2 3
FULL

COMB ATTACHMENTS
BLADE LIFE
MOTOR LIFE
BATTERY LIFE
ENVIRONMENTAL DISPOSAL
You may adjust the cutting length from 3 - 12mm by attaching the comb attachment.
1. The cutting length is marked on the comb attachments.
2. Select a suitable size and slide the blade into the comb attachment.
*The service life of the blade may be shortened in the following situations:
1. The blade has not been lubricated properly on a regular basis.
2. The blade cuts unclean hair or objects other than hair.
3. A foreign object damages the blade edge.
4. The blade is subjected to an impact.
If the cutting efficiency is reduced substantially despite proper maintenance, the
blade has exceeded its service life and should be sharpened or replaced.
*No maintenance is required for the motor.
*Professional DC motor.
*The service life of the motor may be shortened in the following situations:
1. The clipper is stored in humid surroundings for long periods.
2. The blade has not been lubricated properly.
3. Stored hair in the blade housing has not been cleaned properly.
4. An incorrect power source is used.
It is the owner’s responsibility to dispose of the
clippers in a reasonable manner after their useful
life. Do not dispose of in household waste.
The clipper can be returned to the place of purchase
for recycling, or taken to your local authority waste
disposal site.
*The service life expectancy of the battery is approximately 3000 recharging cycles.
After that the charge will gradually drain and the power will be reduced.
*The service life of the battery may be shortened in the following situations:
1. The battery is stored in humid surroundings for long periods.
2. The battery is overcharged.
3. The battery is over depleted (when the battery is out of power, the clipper is kept
in the switched - on position for long periods).
4. The trimmer is always used plugged in.
5. The trimmer has not been charged for more than 3 months.
*When not in regular use, it is recommended to recharge the battery at least every 3
months.
*If cordless operation lasts for less than 10 minutes, despite proper charging, the
battery has exceeded its service life and should be replaced.
The classic clippers are manufactured to comply with all relevant standards and
transportation requirements.
CE: SEM12040474 MSDS: W12143012916D
GS: Z2M21303-0018 UN38.3: W12143012621D
KC: 20130916-0064 BY SEA: W12143012811D
3C: 2009010907343872 BY AIR: W12143012711D
4