KITCHEN KIT 600 Larder Cabinet User manual

BA20-80A / 01.2021
Quick Build Cabinets.kitchenkit.co.uk
Tower Cabinets
Installation Guide

Introduction
This guide is intended as a supplement to the assembly instructions supplied with individual cabinets.
Due to the large variety of door and appliance congurations, a small number of modications may
be needed during installation as shown below.
This avoids the need for multiple drillings to the cabinet, which looks unsightly – and may only be
needed on rare occasions.
NOTE
Ensure all tower cabinets are securely xed to the wall using appropriate xings to suit the wall
type. See Appendix for more information on xing cabinets to the wall.
Before you get stuck in; take ve minutes to review this installation guide.
Please note the following points:
•Appliance Housing Back Panels will need to be cut to length to suit the chosen unit
type – these sizes are shown on individual unit pages.
•In a limited number of congurations, such as drawer and fridge/freezer options,
additional drilling is required to the cabinet ends – these positions are shown on
individual unit pages.
•Take care to position xed and adjustable shelves as shown on individual pages.
•Ensure the cabinet is xed to the wall.
AdjustableFixed
Shelves
Note that cabinets are supplied with 3x Fixed and 1x adjustable shelf. All appliances must have a xed
shelf above & below them – adjustable shelves are only intended for storage purposes.
Back Panels
Back panel heights on appliance housing units
vary depending on door congurations – cutting
dimensions are shown on individual unit pages.
i

Contents
Introduction ................................................................................................................................................................................................i
Contents.......................................................................................................................................................................................................ii
Kitchen Units
Larder Units
600 Larder Cabinet ..................................................................................................................................................................... 1
Integrated Cooking
600 Single Oven Housing..........................................................................................................................................................2
600 Double Oven Housing.......................................................................................................................................................3
600 Oven plus Microwave Housing.....................................................................................................................................4
Integrated Cooling
600 Fridge & Freezer Housing.................................................................................................................................................5
Appendix
Fixing Cabinets to the wall.................................................................................................................................................. A-1
Fixed Shelves............................................................................................................................................................................... A-1
600 Larder Cabinet
1245 Door
715 Door
Fixed Shelf
Adjustable Shelf
Fascias
Cabinet
Back Panels
Large Back Panel
'H' Section
Large Back Panel
Fixed Shelf
Fixed Shelf
ii

600 Larder Cabinet
1245 Door
715 Door
Fixed Shelf
Adjustable Shelf
Fascias
Cabinet
Back Panels
Large Back Panel
'H' Section
Large Back Panel
Fixed Shelf
Fixed Shelf
1

Fascias
Cabinet
Back Panels
600 Single Oven Housing
645 Door
715 Door
Fixed Shelf
Adjustable Shelf
Fixed Shelf
712 mm
604 mm
Large Back Panel
Large Back Panel
(Position at desired height)
Cut height of the large
back panels to the sizes
shown – screw fix to the
rear edge of the fixed shelf
636 mm
Fixed Shelf
2

Fascias
Cabinet
Back Panels
600 Single Oven Housing
645 Door
715 Door
Fixed Shelf
Adjustable Shelf
Fixed Shelf
712 mm
604 mm
Large Back Panel
Large Back Panel
(Position at desired height)
Cut height of the large
back panels to the sizes
shown – screw fix to the
rear edge of the fixed shelf
636 mm
Fixed Shelf
Fascias
Cabinet
Back Panels
600 Double Oven Housing
490 Door
570 Door
Adjustable Shelf
Fixed Shelf
Fixed Shelf
566 mm
895 mm
Large Back Panel
Large Back Panel
492 mm
Cut height of the large
back panels to the sizes
shown – screw fix to the
rear edge of the fixed shelf
3

Fascias
Cabinet
Back Panels
600 Oven plus Microwave Housing
450 Door
450 Door
Fixed Shelf
Fixed Shelf
Fixed Shelf
445 mm
446 mm
Large Back Panel
Large Back Panel
Cut height of the large
back panels to the sizes
shown – screw fix to the
rear edge of the fixed shelf
Position this fixed shelf
to suit your appliances,
as they vary by
manufacturer
98 mm
114 mm
114 mm
98 mm
600 Fridge & Freezer Housing
1245 Door
715 Door
No Back Panel used, please
discard ALL back panel
components supplied.
Fascias
Cabinet
Back Panels
We recommend fitting
two of the surplus fixed
shelves at the rear edge
of the cabinet
(vertically) to give it
rigidity and stability
during installation
4

Fascias
Cabinet
Back Panels
600 Oven plus Microwave Housing
450 Door
450 Door
Fixed Shelf
Fixed Shelf
Fixed Shelf
445 mm
446 mm
Large Back Panel
Large Back Panel
Cut height of the large
back panels to the sizes
shown – screw fix to the
rear edge of the fixed shelf
Position this fixed shelf
to suit your appliances,
as they vary by
manufacturer
98 mm
114 mm
114 mm
98 mm
600 Fridge & Freezer Housing
1245 Door
715 Door
No Back Panel used, please
discard ALL back panel
components supplied.
Fascias
Cabinet
Back Panels
We recommend fitting
two of the surplus fixed
shelves at the rear edge
of the cabinet
(vertically) to give it
rigidity and stability
during installation
5

!
Fixing cabinets to the wall
Please ensure the cabinet is xed securely to the wall and also to the adjacent cabinets.
•For 600 wide appliance housing units, this can be done using metal angle brackets or
appropriate xings (not supplied) behind the appliance, before it is slid into position.
•For Larder Units, this can be done at the top of the cabinet, using metal angle
brackets or appropriate xings (not supplied). It is essential that the cabinet is
prevented from tipping forward, which could cause injury or damage.
Appendix
Fixed Shelves
The xed shelf system uses a metal camlock housing, together with a screw-in bolt that xes into the
cabinet end panel.
1. Use a soft rubber mallet to
tap the Rax connector hous-
ing into the pre-drilled holes.
2. The screw-in bolt xes into
the relevant holes in end panel;
do not overtighten. The shelf
drops into position as shown.
3. Lock o the ttings via the
posidrive screw head inside the
Rax housing.
Fixed Shelves
NOTE
All appliances must be seated on a Fixed Shelf. Never use an adjustable shelf for this purpose.
!
A-1