KitchenAid KHGL9010B User manual

Instructions for use
NL
GB

Product description and symbols 4
Using the burners 4
Practical advice on using the hob 5
Positioning the pan supports and Wok pan adapter 6
Installation distances and measurements (mm) 7
Injectors table 7
Warnings and suggestions 8
Safeguarding the environment 9
EC Declaration of conformity 9
Installation 10
Gas connection 10
Electrical connection 11
Installation 11
Adaption to a different type of gas supply 12
Replacing the injectors 12
Regulating the minimum flow level of the gas taps 12
General cleaning and maintenance 13
Care and maintenance of the hob parts 13
Troubleshooting guide 14
After Sales Service 14

1. Central removable pan support
2. Removable side pan support
3. Auxiliary burner
4. Semi-rapid burner
5. Rapid burner
6. Semi-rapid burner
7. Professional triple crown WOK burner
8. Auxiliary burner control button
9. Semi-rapid burner control button
10. Rapid burner control button
11. Semi-rapid burner control button
12. Professional triple crown WOK
burner control button
Control Symbols
Off
Maximum flame
Minimum flame
Product description and symbols
To turn on one of the burners:
1. Turn the corresponding control knob
anticlockwise until the indicator coincides with
the maximum flame symbol .
2. Press the control knob to ignite the burner.
3. Once the burner has been lit, keep the control
knob pressed for 5 seconds, allowing the safety
thermocouple to fitted to the gas burner to
engage. The safety thermocouple switches off
the gas supply to the burner should the flame
accidentally go out (a gust of wind or spillage, or
temporary interuption of the gas supply).
If the burner does not ignite within about 15
seconds, switch off the burner, check the
fitting of the burner cap and plate for correct
fitting. Wait at least 1 minute before trying
again.
If the burner goes out when the control knob
is released, the thermocouple did not engage.
wait al least 1 minute before repeating strps 1
to 3.
Using the burners
4

Read these instructions to get the best from your
hob:
- Use pans with a diameter suitable for the burner
you are using ( see table opposite)
- Only use plat bottomed pans
- Use the right amount of water for cooking the food.
Prevent unnecessary water loss by using the lid.
- Do not use pans that protrude over the edge of
the hob.
You should never use:
- Cast iron or steatite stone griddles or terracotta
pots or pans.
- Convectors such as metal netting or other.
- The use of two burners simultaneously with just
one container such as a fish kettle.
Important:
Do not rest and/or drag the pan supports upside
down on the hob as this could scratch it.
Failure to comply with these
recommendations could lead to your glass
ceramic hob getting damaged or broken and
the safety of your equipment being
compromised.
Burner Pan diameter
wok from 24 to 26 cm
rapid from 24 to 26 cm
semi rapid from 16 to 24 cm
auxiliary from 8 to 14 cm
Practical advice on using the hob
5

To facilitate positioning of the pan supports on the hob, it is recommended to start by fitting the central
pan support (1).
Place the central pan support on the surface using the double crown burner and the centre knob as a
reference.
Side pan supports (2)
Fit one pan support ensuring that the burner’s cap pins are correctly centred on the lateral burners and
the hooks on the side of the central pan support (recesses for the pins are provided on the underside of
the grill). Repeat the procedure with the other pan support.
Positioning the pan supports and Wok pan adapter
6
2 2
1

If a hood is installed above the hob, read the instructions for fitting the hood where it indicates the correct
distances to be complied with.
Installation distances and measurements (mm)
840
+2
- 0
490
+2
- 0
860
510
45
min. R 6,5
max R 16
63 min.
7
Category II2L3B/P
Type of gas used Type of Injector Nominal heat Nominal Reduced heat Gas presssure
burner marking flow kW consumption flow kW (mbar)
min. nom. max
NATURAL GAS wok 3C 151 4,00 443 l/h 1,55
(Methane) rapid 132 3,00 332 l/h 0,60
G25 semi-rapid 100 1,65 183 l/h 0,35 20 25 30
auxiliary 79 1,00 111 l/h 0,35
LIQUID wok 3C 102 4,00 291 g/h 1,55
PETROLEUM GAS rapid 87 3,00 218 g/h 0,60
(Butane) G30 semi-rapid 67 1,65 120 g/h 0,35 25 30 35
(Propane) G31 auxiliary 50 1,00 73 g/h 0,35
Type of gas used Configuration Nominal heat Overall nominal Required air (m3)
model flow kW consumption for the combustion 1 m3of gas
G25 25 mbar 3C - R - SR - SR - AUX 11,30 1252 l/h 8,187
G30/G31 30 mbar 3C - R - SR - SR - AUX 11,30 822 g/h 30,94
Electric Power: 230 V ~ 50 Hz
Injectors table

To get the most out of your hob, please read
the instructions carefully and keep them for
future consultation.
• These instructions are only valid in the countries
whose destination symbol is shown on the serial
number plate on the hob.
• The packing (plastic bags, expanded
polyurethane, etc) pose a potential threat to
children and should be disposed of carefully.
• Check the appliance has not been damaged
during transportation and remove all
protective packing and films before
installation.
• This hob (cat. 3) was designed to be used
exclusively for cooking food in household
surroundings. Any other use (for example
heating rooms) should be regarded as
improper and dangerous.
• The installation and connection of this
appliance to a gas or electrical supply must
be carried out by a competant, qualified
person in compliance with current
legislation.
• This appliance should be installed in
compliance with standards in force and
only used in well ventilated rooms. Read
the instructions before installing and using
this appliance.
• The pre-fitted gas connector and it's supply
pressure are shown on the label attached
to the bottom of the hob. If this type of gas
supply is not being used, please refer to
the section called Adaption to different
types of gas supply on page 11.
Note:
• Incorrect placement of the pans supports can
scratch the hob. To avoid this always ensure
that the rubber feet on the bottom of the pan
supports are the only part of the pan supports
that touch the hob and do not drag the pan
supports accross the hob surface.
• On the glass surface do not use:
- Cast iron grills, terracotta pots or pans.
- Heat convectors (e.g. metal netting).
- Using two burners to cook 1 pan.
• In the event of prolonged usage, additional
ventilation may be required (opening a window
or increasing the extration speed of the hood).
Warning
• Keep children away from the hob when in use
and don't let them play with the control knobs
or any other part of the appliance.
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensor or mental capabilities or lack of
experience and knowledge unless they have
been given initial supervision or instruction
concerning use of the applaince by a person
responsible for their safety.
• Do not let children play with the pan supports.
The rubber feet on the underneath of the pan
supports could be swallowed by small and cause
serious injury or suffocation.
• Before replacing the pan supports on the hob,
please check that all the rubber feet are in
place.
• Each time you finish using the hob, always check
that the control buttons are in the off position
and shut off the tap to the gas mains or cylinder.
• Do not obstruct the air vents at the back of the
appliance in any way.
Warnings and suggestions
8

Packing
The packing material is 100% recyclable and is
labelled with the recycling symbol . Please
dispose of all packing responsibly and carefully.
Product
This appliance is marked according to the
European Directive 2002/96/EC, Waste Electrical
and Electronic Equipment (WEEE).
By ensuring that this product is disposed of
correctly, you will help prevent potentially negative
consequences for the environment and human
health. The symbol on the product, or on
the documents accompanying this appliance
indicates that this product should not be disposed
of as household waste. Please dispose of this
appliance at an Electrical & Electronic Equipment
Collection point as in accordance with local
environmental regulations for waste disposal. For
details of your local Collection Point please contact
your Local Authority.
Safeguarding the environment
9
EC Declaration of conformity
This appliance has been designed, constructed and marketed in compliance with:
- safety requirements of "GAS" Directive 2009/142/EC (ex-90/396/EEC);
- safety objectives of "Low Voltage" Directive 2006/95/EC (which replaces 73/23/EEC and subsequent
amendments);
- protection requirements of "EMC" Directive 2004/108/EC.
This appliance is suitable for contact with foodstuffs and complies with EC Regulation no. 1935/2004.

Technical information for the installer
• This appliance can be built into a 20mm to
40mm thick worktop.
• If no oven is to be installed below the hob, a
panel must be fitted under the hob to prevent
hob damage and protect the cupboard contents.
This panel must cover the whole of the
underside of the hob and must be positioned so
that an air gap of at least 20mm between the
panel and hob underside is maintained, as a
minimum, and as a maximum 150mm to the
underneath of the work surface.
• This hob is designed to operate perfectly with
any oven in the KitchenAid range. The
Manufacturer declines all responsibility should
any other make of oven be installed.
The manufacturer declines all responsibility
should another make of oven be installed.
Before installation, please ensure that:
•Warning: this is a heavy products which
requires the installation to be carried out
by two people.
• The gas supply (type and pressure) and the
calibration on the hob are compatible ( see
serial number plate on the hob and the table on
page 7).
• The cabinetry and appliances surrounding/next
to the hob are heat resistant and in compliance
with local regulations.
• The products of combustion are removed from
the atmoshere in the room by using an
extraction hood or electrical fan installed to the
walls and or windows, in line with current
regulations.
• The air circulates naturally through a suitable
opening that is no less than 100cm2in cross
section, which must be:
- permanent and accessible on the walls of the
room being ventilated and extracting towards
the outside.
- created in such a way that the openings both
inside and out cannot be obstructed, even in
error.
- Protected by plastic grill, metallic netting etc
that should not reduce the 100cm2cross section
- Located in such a position so as not to
interfere with the extraction of the products of
combustion.
Installation
Connection to the mains gas system must be carried out by a
competant, registered person, in compliance with current
legislation.
• The connection of the hob to the gas mains network or gas
cylinder must be done using a rigid copper or steel pipe with parts
that comply with local standards, or using a flexible stainless steel
pipe with continuous surfaces that comply with local standards.
The flexible metallic pipe should be no longer than 2 linear
metres.
• Before connecting the pipe with the rubber part (A), ensure that
seal (B) is in place (this part, provided complies with EN549).
Warning: if you use a stainless steel flexible pipe, it must be installed
in such a way that it does not come into contact with mobile parts
like drawers or kitchen cupboards and passes at a point free of
obstacles where it can be examined in its entirety.
• After connecting to the gas mains, use soap and water to check
there are no leaks.
Gas connection
10

The electrical connections must comply with current
legislation and be carried out by a qualified, competent
person.
• Information on the voltage and power absorbed are shown on the
serial no. plate.
• The appliance must be earthed.
• When installing the appliance, we recommend that this hob
is protected by a 3mm bi-polar switch.
• If damaged, the power cable must be replaced with an
identical type of powercable ( H05V2V2-FT90 ºC, or
H05RR-F type). We recommend that this operation be
conducted by our After Sales Service. Please contact our
Customer Care Centre on 00800-3810-4026.
• Do not use extension cables.
• The manufacturer declines all responsibility for damage to
persons, pets or goods as a result of failure to comply with
the regulations above.
Electrical connection
L
Earth
(yellow/green)
N
1. After cleaning the surfaces around the edges, fit the seal provided
around the hob.
2. Position the hob inside the opening according to the sizes
indicated in the description sheet.
3. Use the rods (A) provided to secure the hob, fixing it with the
proper screws to adapt it to the thickness.
Warning: the electrical power cable must be long enough to
allow the hob to be lifted out from above.
Installation
11
A

Note: see the description sheet for the model.
1. Remove the pan support (A).
2. Remove the burners (B).
3. Unscrew the injector (C) with a box spanner 7.
4. Replace the injector with the one for the new gas.
Note: before installing the hob, remember to attach the gas
calibration label provided with the replacement injectors so that it
covers the information already present.
Replacing the injectors
If you are using a different kind of gas from the one
indicated on the serial no. plate and the orange
label on the back of the hob, you must replace the
injectors; in the case of the Wok burner, adjust the
primary air (see Injector table on page 7).
The orange label should be removed and kept
together with the manual.
Use pressure regulators suitable for the gas
pressures indicated on page 7
• In order to replace the injectors, contact the
Customer Care Centre on 00800-3810-4026,
or a qualified electrician.
• Injectors not supplied as standard should be
requested from the Customer Care Centre on
00800-3810-4026.
• Regulate the minimum levels of the taps.
Note: with liquid petroleum gas ( G30/G31)
the bypass screw must be screwed in fully. If
you then experiance difficulty in turning the
control knob, contact our After sales Service
though our Customer Care Centre on
00800-3810-4026, who will arrange for a
replacement after ascertaining that the tap is
damaged.
Adaption to a different type of gas supply
12
Regulating the minimum flow level must be done with the tap at the
lowest position (small flame) .
There is no need to regulate the primary air in the burners.
To ensure the minimum level is properly regulated, remove the control
knob and adjust the screws found on the tap as follows:
1. tighten to reduce the height of the flame 1 (-)
2. slacken to increase the height of the flame (+);
3. With the burners on, rotate the buttons from the maximum to
the minimum position to check the stability of the flame.
Once you have finished regulating, close up the seals again using sealing
wax.
Regulating the minimum flow level of the gas taps

Always disconnect the hob from the electrical
power supply and wait until it cools before
cleaning and/or doing maintenance work.
In order to keep your hob in good condition, you
must keep it clean, removing any remaining food
each time you use it.
Cleaning the surface of the hob:
• the enamelled parts and the glass should be
washed with lukewarm water and a mild
cleaning product.
• Do not use harsh or corrosive products,
chloride based products or scourers.
• Do not steam clean.
• Do not use inflammable products.
• Do not leave acidic or alkaline based products
like vinegar, mustard, salt, sugar or lemon juice
lying on the hob.
General cleaning & maintenance
The pan supports, the caps and burners can be
removed to make cleaning easier.
1. Hand wash carefully with hot water and a
neutral cleaning product making sure you
remove any ingrained dirt and ensuring that
none of the openings on the burner is
obstructed.
2. Rinse and dry carefully.
3. Correctly refit the burners and caps in their place.
4. Make sure when replacing the pan supports that
the area for resting the pots is centred with the
burner.
Note: in the models fitted with electrical igniter
and safety thermocouples, you have to clean the
end part very carefully to ensure they work
properly. Frequently check them and, if necessary,
clean with a damp cloth. Any remaining ingrained
food should be removed with a toothpick or
needle.
To avoid damaging the electrical igniter do
not use it when the burners are not in their
place.
Care and maintenance of the hob parts
13

If the hob is not working properly work through
the this guide before contacting our Customer
Care Centre.
The burner does not ignite, or the flame is
unsteady? Check that:
1. the gas, or electricity supply has not been
interrupted and that the control knob is turned
fully on.
2. the gas supply has not run out.
3. the openings on the burner have become
blocked.
4. the end of the electronic igniter is clean.
5. all the parts on the burner are properly
positioned.
The flame doesn’t stay on? Check that:
1. the button was pushed in properly when turning
on the burner for the time required to activate
the safety thermocouple.
2. the burner’s openings are not blocked in
relation to the thermocouple.
3. the end part of the thermocouple is clean.
The pans are not stable? Check that:
1. the bottom of the pot is perfectly flat.
2. the pot is centred on the burner.
3. the pan supports are correctly positioned with
all the rubber feet in place.
If, despite all these checks and after tuning the hob
off and on again, you are still experiancing
problems please contact our Customer Care
Centre on 00800-3810-4026.
Troubleshooting guide
Before contacting our Customer Care Centre please check to
see if the problem can be fixed by refering to the
troubleshooting guide.
1. If the fault persists contact us on 00800-3810-4026. We will ask
you for some information, it will help us, help you if you have the
following information ready to give us:
• a short description of the falut
• the serial number and model number of the appliance
• the service number ( the number after the word service on the
rating plate on the bottom of the hob. The service number can
also be found in the warranty booklet.
• your name, full address including postcode and telephone number.
Note: If there is a problem with your hob, failure to contact us
could seriously compromise the safety and quality of this
appliance.
After Sales Service
14

5019 719 01154/A
Printed in Italy n
06/10
Whirlpool Europe S.r.l.
Viale G. Borghi, 27 - 21025 Comerio (VA)
Phone [phone] - Fax [phone]
www.whirlpool.eu