KitchenAid KDRS407VSS01 User manual

KaetchenAid
INSTALLATION INSTRUCTIONS
30" (76.2 CM), 36" (91.4 CM) AND 48" (121.9 CM)
COMMERCIAL STYLE DUAL FUEL
CONVECTION RANGE
tor residential use only
al
INSTRUCTIONS D'INSTALLATION
CUISINIERE A CONVECTION - STYLE
COMMERCIAL A BI-COMBUSTIBLE
DE 30" (76,2 CM), 36" (91,4 CM) ET 48" (121,9 CM)
ey a we % %
wk
agent
S
Ly
elle uniquement TESS
Table of Contents/Table des MatiGres............cccccccccecsssssssssseseeceececeeateaseeeseeeeeeueseseeaneasaeens 2
IMPORTANT:
Save for local electrical inspector's use.
Installer: Leave installation instructions with the homeowner.
Homeowner: Keep installation instructions for future reference.
IMPORTANT :
A conserver pour consultation par l'inspecteur local des installations électriques.
Installateur : Remettre les instructions d'installation au propriétaire.
Propriétaire : Conserver les instructions diinstallation pour référence ultérieure.
W10349767A

TABLE OF CONTENTS TABLE DES MATIERES
RANGE SAFETY 3 SECURITE DE LA CUISINIERE...........ccssccssscssssssesscescesstesnteneesseenes 30
INSTALLATION REQUIREMENTS..........:cccccssessseseesseeesteneenneeneee 4 EXIGENCES D’INSTALLATION ........:ccccscesseseesteessenteeestenneenenees 31
Tools And Parts ......ccccccsscccsssssesecsseeeecsseeeesssneeeeesseneeeeseaeeeessneeeseas 4 Outillage et PIECES... eesscccssssceecsssseeessseeeseeeseeesssseeessseesesees 31
Location REQUIFeMENtS ...........cccccccccessecsssessssecseeeeseesseeseeeeeseeeses 5 Exigences d'emplaceMent.........ccccccsscccssssessssteesssseesesssseesssees 32
Water Filtration System Location Requirements............:ccccce 7 Exigences d'emplacement du systeme
Water Supply Requirements voce c edna ed ee ecu ecu ec een cueenecenieseuaneenennnenes 7 le filtration de |'CQU ......ceesscecssssceeeesseeessseeesessseeeesssseeesseeeeseseas 34
Electrical Requirements - U.S.A. Only ...eseeseseeseseeseesererseeseeeeeee 7 Spécifications de lalimentation en Cau oo... eee 35
Electrical Requirements - Canada Only .......cececeeseeseeee certo 8 Spécifications de linstallation @lectrique ..........cccccceeesseeeenes 35
Gas Supply Requirement ........ccccccsssecssescesescesescesescessescesesceseseens 9 Spécifications de l'alimentation @N Gaz 0... eee 35
INSTALLATION INSTRUCTIONS .........ccccsccesstesessteestentenstennsenens 10 INSTRUCTIONS D’INSTALLATION..........::cccssesesesesesenenenenenenes 37
Unpack Range... scence 10 Déballage de la CUISINIGre «0.2... sess sess ecseesteeseesceneeseeseeseseneeaeees 37
Install Optional BaCkQuat........seesesssessesssesseeseerseeeeeeseeeeeeaeeeees 11 Installation du dosseret facultatif ...........eseessessessecseseesesseseeeneees 37
Install Anti-Tip Bracket ........secccseessesseeeesesesseeseeressteanseeeeeeaneeees 11 Installation de la bride antibasculeMent ...........seseesseeseeseeeees 37
Electrical Connection - U.S.A. OMI) ....cccccessesssesestsssesesteeeeeens 12 Installation du systeme de filtration de CU... teeter 38
Install Water Filtration SyStem .........cccccsecsseseesseceseeseseeeeseeeeees 14 Raccordement aU Gaz ......eccceeccescceceeeeceneeeeeeeeseeeeeeeeseneeseneeseneeees 40
Make Gas Connection ........ccccccccccessecsesseeeeesseeeeessseeeeesseeeeesseeeess 15 Vérification de l'emplacement de la bride
Verify Anti-Tip Bracket Location ......cccceescsessseeeeseseeseeeeesens 16 ANTIDASCUIEMENL .......cceccccccceecsssesseeeeeeecensssneeeaeeeeeeeceseesessaeeeeeeeeess 40
Level RAnge....cccsssssssssessecssecssessesssesseesscssecsseesueesecssecasecsnesneessenses 16 Reglage de l'aplomb de la CUiSiNi€re .... eee eee 40
Install Grill Grease Trays w.c.ceeccsesscssssesesesesessesesesscsestssstsessesaees 16 Installation des plateaux a graisse GU fil... eee At
Install Griddle oo... cecccessccssessccssesseesseesssesccssecsseesessesseessecssecsneessensee 17 Installation de la Plaque fire ........seessesseseesee ees eeseeeeeseeseesneeaeens 42
Electronic Ignition SYStOM ...cseesesesesesessessssessssessesesenseseseeeees 17 Systeme d'allumage Electronique... escent 42
Reinstall Kickplate........cccssecssesssessecsscsseessesseesseesscsseessesseesseaneensee 19 Reinstallation AU garde-pieds ......... cesses eeseeseenneeeeees 44
Complete Installation ....c.c.c.ccccesscsesesesssesesscsesssessseverseseseseresnens 19 Achever l'installation ..........ccccccssssssssseeceeeeessscsssssneeeseeeessssneeeeeeeens 44
GAS CONVERSIONS 20 CONVERSIONS POUR CHANGEMENT DE GAZ.........00..000.0000+ 45
LP Gas Conve rSion .......:ccecceseccecececeeeeceeeseeeeaeseeeseaeesaesenessresaeeaees 20 Conversion pour l'alimentation aU Propane... eee 45
Natural Gas Conversion. ........:ccccccscseceeceeeeeeeeeeceeesaeeeeeseeesseeseteaees 22 Conversion pour l'alimentation au gaz NatUrel eee 47
Strip CirCuits.... ccc cscecescsescssescssescssesesesseseeseseessseseeseseeeseeteceseasenes 24 Schémas des circuits GU FOUN oe eeneententeeneaeenties 50
Wiring Diagrams .......cccccccccecsssesesetcescsesesesesesesssesecececscececececeeees 25 SCHEMA de CADAGES «0. sescccceeeeeseneneteneeeeeeeseseseseseseneseneeeeees 51

RANGE SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER?” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
A DANG ER follow instructions.
You can be killed or seriously injured if you don't follow
AWARNING instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
WARNING: If the information in this manual is not followed exactly, a fire or explosion
may result causing property damage, personal injury or death.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
- WHAT TO DO IF YOU SMELL GAS:
e Do not try to light any appliance.
e Do not touch any electrical switch.
e Do not use any phone in your building.
e Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
instructions.
e If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency or
the gas supplier.
WARNING: Gas leaks cannot always be detected by smell.
Gas suppliers recommend that you use a gas detector approved by UL or CSA.
For more information, contact your gas supplier.
If a gas leak is detected, follow the “What to do if you smell gas” instructions.
In the State of Massachusetts, the following installation instructions apply:
@ Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by
the State of Massachusetts.
@ If using a ball valve, it shall be a T-handle type.
@ A flexible gas connector, when used, must not exceed 3 feet.

AWARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Connect anti-tip bracket to wall behind range.
Reconnect the anti-tip bracket, if the range is moved.
Failure to follow these instructions can result in death or serious burns to children and adults.
INSTALLATION REQUIREMENTS
ry
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed
m Tape measure %6" carbide tip masonry bit
mg #2 Phillips screwdriver m= Marker or pencil
mw '%" x 4%" flat-blade gm = Pipe-joint compound
screwdriver resistant to LP gas
m Level m Noncorrosive leak-detection
= Drill solution
m Wrench or pliers m Tubing cutter
m Pipe wrench For LP/Natural Gas
m Adjustable wrench or Conversions .
54" wrench T15 Torx screwdriver
m %" drive ratchet m %" socket
a 1%" aril bit m Adjustable wrench
m ‘%e" combination wrench ™ 2’ deep-well socket
a 14", %", %e" nut drivers = 7mm nut driver
mg Masking tape
Parts supplied
Check that all parts are included.
a Anti-tip bracket kit
A. Anti-tip bracket
B. #8-18 x 1" Phillips head screws (4)
NOTE: Anti-tip bracket must be securely mounted to
subfloor. Thickness of flooring may require longer screws to
anchor bracket to subfloor. Longer screws are available from
your local hardware store. See “Install Anti-Tip Bracket”
section.
m Gas pressure regulator
T®TORX is a registered trademark of Saturn Fasteners, Inc.
4
Tools ar
pee
e pond
Burner grates
ay
Burner heads and caps
Grill grate (on grill models)
Wave tray (on grill models)
Flame spreader (on grill models)
Burner assembly (on grill models)
Grease trays (2) (on grill models)
Griddle drip tray (on griddle models)
Grill drip tray (on grill models)
Island trim
LP orifice package (W10221288)
Conversion label (W10221320)
NOTE: The cooktop is manufactured for use with Natural gas.
To convert to LP gas, see the “Gas Conversions” section.
Additional Parts Supplied on Steam-Assist Models
m Model W10049700 water filter kit
mg 4" to %" water supply union
Parts needed
m Power supply cord kit:
m= 30" (76.2 cm) and 36" (91.4 cm) models - A UL listed
40 amp power supply cord kit
m 48" (121.9 cm) models - A UL listed 50 amp power supply
cord kit marked for use with nominal 1%" (84.93 mm)
diameter connection openings
A UL listed strain relief
UL listed wire connectors
All models must be installed with a backguard if installing at
zero clearance to a combustible backwall. See “Cabinet
Dimensions” in the “Location Requirements” section for
installation requirements.
mw 30" (76.2 cm) Adjustable Backguard
Order Part Number 8285148
gm 36" (91.4 cm) Adjustable Backguard
Order Part Number 8284756
m 48" (121.9 cm) Adjustable Backguard
Order Part Number 8284755
mg 9" (22.9 cm) Backguard for 30" (76.2 cm) Ranges
Order Part Number W10115773
gm 9" (22.9 cm) Backguard for 36" (91.4 cm) Ranges
Order Part Number W10115776
gm 9" (22.9 cm) Backguard for 48" (121.9 cm) Ranges
Order Part Number W10115777

m 22" (55.9 cm) Backguard with Shelf for 30” (76.2 cm)
Ranges
Order Part Number W10225950
m 22" (55.9 cm) Backguard with Shelf for 36" (91.4 cm)
Ranges
Order Part Number W10225949
m 22" (55.9 cm) Backguard with Shelf for 48" (121.9 cm)
Ranges
Order Part Number W10225948
To order, see the “Assistance or Service” section of the Use
and Care Guide.
Additional Parts Needed on Steam-Assist Models
mg Tubing staples/retainers
mg %4"O.D. flexible codes approved water supply tubing (to
make water connection)
m Water connection device (to connect 44" O.D. tubing to
water source). Check local codes for type of connection
required.
Check local codes and consult gas supplier. Check existing gas
supply and electrical supply. See “Electrical Requirements” and
“Gas Supply Requirements” sections.
It is recommended that all electrical connections be made by a
licensed, qualified electrical installer.
High Altitude Conversion
To convert the cooktop for elevations above 6,560 ft (1999.5 m),
order a High Altitude Conversion Kit.
mw Part Number W10237848 - LP high altitude
mg Part Number W10160841 - Natural gas high altitude
To order, see the “Assistance or Service” section of the Use and
Care Guide.
IMPORTANT: Observe all governing codes and ordinances. Do
not obstruct flow of combustion and ventilation air.
g_ It is the installer’s responsibility to comply with installation
clearances specified on the model/serial rating plate. The
model/serial rating plate is located on the right vertical
surface of the oven door frame.
gm It is recommended that a 600 CFM or larger range hood be
installed above the range.
gm It is not recommended that a microwave hood combination
be mounted above the range.
m Recessed installations must provide complete enclosure of
the sides and rear of the range.
mg To eliminate the risk of burns or fire by reaching over heated
surface units, cabinet storage space located above the
surface units should be avoided. If cabinet storage is to be
provided, the risk can be reduced by installing a range hood
that projects horizontally a minimum of 5” (12.7 cm) beyond
the bottom of the cabinets.
g_ All openings in the wall or floor where range is to be installed
must be sealed.
Do not seal the range to the side cabinets.
Cabinet opening dimensions that are shown must be used.
Given dimensions are minimum clearances.
mg The anti-tip bracket must be installed. To install the anti-tip
bracket shipped with the range, see “Install Anti-Tip Bracket”
section.
m Grounded electrical supply is required. See “Electrical
Requirements” section.
m Proper gas supply connection must be available. See “Gas
Supply Requirements” section.
m Contact a qualified floor covering installer to check that the
floor covering can withstand at least 200°F (93°C). Use an
insulated pad or 4%" (0.64 cm) plywood over carpet and under
range if installing range over carpeting.
IMPORTANT: To avoid damage to your cabinets, check with your
builder or cabinet supplier to make sure that the materials used
will not discolor, delaminate or sustain other damage. This oven
has been designed in accordance with the requirements of UL
and CSA International and complies with the maximum allowable
wood cabinet temperatures of 194° (90°C).
Mobile Home - Additional Installation Requirements
The installation of this range must conform to the Manufactured
Home Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 24, HUD Part 280). When such standard is not
applicable, use the Standard for Manufactured Home
Installations, ANSI A225.1/NFPA 501A or with local codes.
In Canada, the installation of this range must conform with the
current standards CAN/CSA-A240-latest edition, or with local
codes.
Mobile home installations require:
m When this range is installed in a mobile home, it must be
secured to the floor during transit. Any method of securing
the range is adequate as long as it conforms to the standards
listed above.
Product Dimensions
30" (76.2 cm) models
A. Optional backguard may be installed
B. 27%" (70.5 cm) depth with control panel, see NOTE*
C. 35%" (89.6 cm) cooktop height when setting on the wheels
D. 30" (76.2 cm) width
E. Model/serial rating plate location

36" (91.4 cm) models
A. Optional backguard may be installed
B. 27%" (70.5 cm) depth with control panel, see NOTE*
C. 35%4" (90.2 cm) cooktop height when setting on the wheels
D. 36" (91.4 cm) width
E, Model/serial rating plate location
48" (121.9 cm) models
NOTE: The following illustration is for dimension planning
purposes only, and the locations and appearances of the features
shown may not match those of your model.
A. Optional backguard may be installed
B. 27%" (70.5 cm) depth with control panel, see NOTE*
C. 35%4" (90.2 cm) cooktop height when setting on the wheels
D. 48" (121.9 cm) width
E, Model/serial rating plate location
*NOTE: When installed in a 24” (61.0 cm) base cabinet with
25" (63.5 cm) countertop; front of oven door protrudes
1%" (4.8 cm) beyond 24” (61.0 cm) base cabinet.
Cabinet Dimensions
Cabinet opening dimensions shown are for 25" (64 cm)
countertop depth, 24" (61 cm) base cabinet depth and
36" (91.4 cm) countertop height. Dimensions must be met in
order to ensure a flush fit to backwall.
6
IMPORTANT: If installing a range hood or a hood liner above the
range, follow the range hood or hood liner installation instructions
for dimensional clearances above the cooktop surface.
Gas
~ installation
area
installation
area*
A. 18" (45.7 cm) upper cabinet to countertop
B. 30" (76.2 cm) model: 30" (76.2 cm) min. upper cabinet width
36" (91.4 cm) model: 36" (91.4 cm) min. upper cabinet width
48" (121.9 cm) model: 48" (1271.9 cm) min. upper cabinet width
C. 13" (33 cm) max. upper cabinet depth
D. For minimum clearance to top of range, see NOTE**
E. 30%" (76.8 cm) on 30" (76.2 cm) models
36%" (92.1 cm) on 36" (91.4 cm) models
484" (122.6 cm) on 48" (121.9 cm) models
F. 6" (15.2 cm) min. clearance from both sides of range to side
wall or other combustible material
G. 15" (38.1 cm)
H. 22" (55.9 cm) on 30" (76.2 cm) models
28" (71.1 cm) on 36" (91.4 cm) models
40" (101.6 cm) on 48" (1271.9 cm) models
11%" (3.8 cm)
J. 3" (7.6 cm)
K.5" (12.7 cm)
L.6" (15.2 cm) on 30" (76.2 cm) models
14" (35.5 cm) on 36" (91.4 cm) models
24" (61.0 cm) on 48" (121.9 cm) models
M. 10%" (26.7 cm)
N. 6" (15.2 cm)
0. 6" (15.2 cm), see NOTE*™*
*NOTE: Receptacle must be rotated 90° for Canadian
installation.
“NOTE: Minimum Clearances
30" (76.2 cm) models: 30" (76.2 cm) minimum clearance
between the top of the cooking platform and the bottom of an
uncovered wood or metal cabinet.
36" (91.4 cm) models: 42" (106.7 cm) minimum clearance
between the top of the cooking platform and the bottom of an
uncovered wood or metal cabinet.
48" (121.9 cm) models: 42" (106.7 cm) minimum clearance
between the top of the cooking platform and the bottom of an
uncovered wood or metal cabinet.
*““NOTE: If backwall is constructed of a combustible material
and a backguard is not installed, a 6” (15.2 cm) minimum
clearance is required for all models.

For best results, do not install the water filtration system outside,
or in extreme hot or cold temperatures. Temperature of water
supply to the water filtration system must be between 40°F/4°C
and 100°F/38°C. Do not install on hot water supply line.
Locate the water filtration system near the cold water supply pipe
under the kitchen sink to filter cold water.
Make sure that the water filter assembly is installed in the upright
position.
It will be necessary to drill a ¥2" (1.8 cm) minimum diameter hole
in the upper right or left rear corner of the side wall of the cabinet
under the sink to route the water supply tubing through to the
range.
Depending on your installation configuration, more routing holes
may be required.
Coil enough flexible codes approved water supply tubing behind
the range to allow for the connection to the range to be made
behind the range prior to setting the range in place.
Typical Installation Configuration
NOTE: For unique installations, contact a licensed plumber.
In Massachusetts, a licensed plumber is required and the
Commonwealth of Massachusetts Plumbing Code 248-CMR
shall be adhered to.
Filter
| assembly
location»
Cold water
supply
Water
A cold water supply with water pressure > between 30 and 120 psi
(207 and 827 kPa) is required to operate the steam feature. In
Massachusetts, plumbing code 248 CMR 3.00 and 10.00 must
be followed and a licensed plumber shall be used. If you have
questions about your water pressure, call a licensed, qualified
plumber.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a
reverse osmosis system going to the water inlet valve of the
range needs to be between 30 and 120 psi (207 and 827 kPa).
If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of 40 psi (276 kPa).
If the water pressure to the reverse osmosis system is less than
AO psi (276 kPa):
m Check to see whether the sediment filter in the reverse
osmosis system is blocked. Replace the filter if necessary.
mg Allow the storage tank on the reverse osmosis system to refill
after heavy usage.
If you have questions about your water pressure, call a licensed,
qualified plumber.
If codes permit and ¢ a separate ground : wire is used, it is
recommended that a qualified electrical installer determine that
the ground path and wire gauge are in accordance with local
codes.
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that the
ground path is adequate.
Do not use an extension cord.
Be sure that the electrical connection and wire size are adequate
and in conformance with the National Electrical Code, ANSI/
NFPA 70-latest edition and all local codes and ordinances.
A copy of the above code standards can be obtained from:
National Fire Protection Association
One Batterymarch Park
Quincy, MA 02269.
WARNING: Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. Check with a
qualified electrician or service technician if you are in doubt as to
whether the appliance is properly grounded. Do not modify the
power supply cord plug. If it will not fit the outlet, have a proper
outlet installed by a qualified electrician.
Electrical Connection
To properly install your range, you must determine the type of
electrical connection you will be using and follow the instructions
provided for it here.
m Range must be connected to the proper electrical voltage
and frequency as specified on the model/serial number rating
plate. The model/serial number rating plate is located on the
right vertical surface of the oven door frame. Refer to the
installations in the “Product Dimensions” section of the
“Location Requirements” section.
mg This range may be manufactured with a 4-wire power supply
cord, or it may not include a power supply cord. If your range
does not include a power supply cord, use a 4-wire power
supply cord rated at 250 volts, 40 or 50 amps and
investigated for use with ranges.
Range Rating* Specified Rating of Power
Supply Cord Kit and
Circuit Protection
120/240 Volts 120/208 Volts Amps Range Size
8.8 - 16.5 kW 7.8-12.5kW 40o0r50** 30" (76.2 cm),
36" (91.4 cm)
16.6-225kW 12.6-18.5kW 50 48" (121.9 cm)
*The NEC calculated load is less than the total connected load
listed on the model/serial rating plate.
“If connecting to a 50-amp circuit, use a 50-amp rated cord with
kit. For 50-amp rated cord kits, use kits that specify use with a
nominal 1%" (34.9 mm) diameter connection opening.
A circuit breaker is recommended.
Wire sizes and connections must conform with the rating of
the range.
m_ The Tech Sheet is located behind the kickplate in a clear
plastic bag.

If connecting to a 4-wire system:
This range is manufactured with the ground connected to the
cabinet. The ground must be revised so the green ground wire of
the 4-wire power supply cord is connected to the cabinet. See
the “Electrical Connection - U.S.A. Only” section.
Grounding through the neutral conductor is prohibited for new
branch-circuit installations (1996 NEC); mobile homes; and
recreational vehicles, or an area where local codes prohibit
grounding through the neutral conductor.
When a 4-wire receptacle of NEMA Type 14-50R is used, a
matching UL listed, 4-wire, 250-volt, 40- or 50-amp, range power
supply cord must be used. This cord contains 4 copper
conductors with ring terminals or open-end spade terminals with
upturned ends, terminating in a NEMA Type 14-50R plug on the
supply end.
The fourth (grounding) conductor must be identified by a green or
green/yellow cover and the neutral conductor by a white cover.
Cord should be Type SRD or SRDT with a UL listed strain relief
and be at least 4 ft (1.22 m) long.
O
UU
U
4-wire receptacle (14-50R)
The minimum conductor sized for the copper 4-wire power
cord are:
A0-amp circuit
2 No.-8 conductors
1 No.-10 white neutral
1 No.-8 green grounding
If connecting to a 3-wire system:
Local codes may permit the use of a UL listed, 3-wire, 250-volt,
40- or 50-amp range power supply cord (pigtail). This cord
contains 3 copper conductors with ring terminals or open-end
spade terminals with upturned ends, terminating in a NEMA Type
10-50P plug on the supply end. Connectors on the appliance end
must be provided at the point the power supply cord enters the
appliance. This uses a 3-wire receptacle of NEMA Type 10-50R.
3-wire receptacle (10-50R)
Xe
Electrical Shock Hazard
Electrically ground range.
Failure to do so can result in death, fire, or
electrical shock.
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrical installer determine that
the ground path and wire gauge are in accordance with local
codes.
Be sure that the electrical connection and wire size are adequate
and in conformance with the CSA Standard C22.1, Canadian
Electrical Code, Part 1 - latest edition, and all local codes and
ordinances.
A copy of the above code standards can be obtained from:
Canadian Standards Association
178 Rexdale Blvd.
Toronto, ON M9W 1R3 CANADA
m Check with a qualified electrical installer if you are not sure
the range is properly grounded.
m When a 4-wire, single phase 250 volt, 60 Hz., AC only
electrical supply is available, a 40-amp minimum circuit
protection is required on 30” (76.2 cm) and 36" (91.4 cm)
ranges and a 50-amp minimum circuit protections is required
on 48" (121.9 cm) ranges, fused on both sides of the line.
m A time-delay fuse or circuit breaker is recommended.
This range is equipped with a CSA International Certified
Power Cord intended to be plugged into a standard 14-50R
wall receptacle. Be sure the wall receptacle is within reach of
range’s final location.
Oo
0
m Donot use an extension cord.

AWARNING
Explosion Hazard
Use a new CSA International approved gas supply line.
Install a shut-off valve.
Securely tighten all gas connections.
If connected to LP, have a qualified person make sure
gas pressure does not exceed 14" (36 cm) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death, explosion, or fire.
Observe all governing codes and ordinances.
IMPORTANT: This installation must conform with all local codes
and ordinances. In the absence of local codes, installation must
conform with American National Standard, National Fuel Gas
Code ANSI Z223.1/NFPA 54 - latest edition or CAN/CGA B149 -
latest edition.
IMPORTANT: Range cooktop must be connected to a regulated
gas supply.
IMPORTANT: Leak testing of the range cooktop must be
conducted according to the manufacturer’s instructions.
Type of Gas
Natural Gas:
This range is design-certified by CSA International for use with
Natural gas or, after proper conversion, for use with LP gas.
mg This range is factory set for use with Natural gas. The model/
serial rating plate located on the right vertical surface of the
oven door frame has information on the types of gas that can
be used. If the types of gas listed do not include the type of
gas available, check with the local gas supplier.
LP Gas conversion:
Conversion must be done by a qualified service technician.
No attempt shall be made to convert the range cooktop from the
gas specified on the model/serial rating plate for use with a
different gas without consulting the serving gas supplier. To
convert to LP gas, use the LP gas conversion kit provided with
your range and see the “Gas Conversions” section. The parts for
this kit are in the literature package supplied with the range.
Gas Supply Line
m Provide a gas supply line of 34" (1.9 cm) rigid pipe to the
range location. A smaller size pipe on longer runs may result
in insufficient gas supply. With LP gas, piping or tubing size
can be ¥2" (1.38 cm) minimum. Usually, LP gas suppliers
determine the size and materials used in the system.
NOTE: Pipe-joint compounds that resist the action of LP gas
must be used. Do not use TEFLON tape.
Flexible metal appliance connector:
g_ If local codes permit, a new CSA design-certified,
4 - 5 ft (122 - 152.4 cm) long, %" (1.6 cm) or
34" (1.9 cm) |.D., flexible metal appliance connector may
be used for connecting range to the gas supply line.
gw A‘%" (1.3 cm) male pipe thread is needed for connection
to the female pipe threads of the inlet to the range
pressure regulator.
m Do not kink or damage the flexible metal tubing when
moving the range.
Rigid pipe connection:
The rigid pipe connection requires a combination of pipe
fittings to obtain an in-line connection to the range. The rigid
pipe must be level with the range connection. All strains must
be removed from the supply and fuel lines so range will be
level and in line.
m Must include a manual shutoff valve:
The supply line must be equipped with a manual shutoff
valve. This valve should be located in the same room but
external to the range opening, such as an adjacent cabinet. It
should be in a location that allows ease of opening and
closing. Do not block access to shutoff valve. The valve is for
turning on or shutting off gas to the range.
A. Gas supply line
B. Shutoff valve “open” position
C. To range
T®TEFLON is a registered trademark of E.l. Du Pont De Nemours and Company.

Gas Pressure Regulator Burner Input Rating - Altitude
The gas pressure regulator supplied with this range must be
used. The inlet pressure to the regulator should be as follows for
proper operation:
Natural Gas:
Minimum pressure: 6" (15.2 cm) WCP
Maximum pressure: 14" (85.6 cm) WCP
LP Gas:
Minimum pressure: 11" (27.9 cm) WCP
Maximum pressure: 14" (85.6 cm) WCP
Contact local gas supplier if you are not sure about the inlet
pressure.
Input ratings shown on the model/serial rating plate are for
elevations up to 2,000 ft (609.6 m).
For elevations above 2,000 ft (609.6 m), ratings need to be
reduced at a rate of 4% for each 1,000 ft (304.8 m).
Gas Supply Pressure Testing
Gas supply pressure for testing regulator must be at least
1" water column pressure above the manifold pressure shown
on the model/serial rating plate.
Line pressure testing above ‘2 psi gauge (14" WCP)
The range and its individual shutoff valve must be disconnected
from the gas supply piping system during any pressure testing of
that system at test pressures in excess of /% psi (3.5 kPa).
Line pressure testing at 2 psi gauge (14" WCP) or lower
The range must be isolated from the gas supply piping system by
closing its individual manual shutoff valve during any pressure
testing of the gas supply piping system at test pressures equal to
or less than ¥ psi (3.5 kPa).
INSTALLATION INSTRUCTIONS
AWARNING
Excessive Weight Hazard
Use two or more people to move and install range.
Failure to do so can result in back or other injury.
1. Remove shipping materials, tape and film from range. Keep
shipping pallet under range. Remove oven racks, grates and
parts package from inside oven.
2. Remove screws from kickplate.
A. Kickplate
B. Remove these screws.
10
ae TP ays pecs
xe
3. Push down on kickplate to release plate from shoulder
screws.
4. Lay kickplate to the side to avoid scratching the stainless
steel.
5. For 48" (121.9 cm) models only, rotate center support
counterclockwise off the pallet until it stops.
NOTE: This support is used only for shipping and is not
needed for installation.
6. Lay a piece of cardboard from side packing on the floor
behind range. Using 2 or more people, firmly grasp each side
of range. Lift range up about 3” (8.0 cm) and move it back
until range is off shipping pallet. Set range on cardboard to
avoid damaging floor.

All ranges may require a backguard. See “Cabinet Dimensions” in
the “Location Requirements” section. See the “Tools and Parts”
section for information on ordering.
Remove island trim and attach backguard using 6 screws, insert
3 from the front and 3 from the back (9" [22.9 cm] backguard is
shown).
& ib, yall pe
AWARNING
©
Tip Over Hazard
A child or adult can tip the range and be killed.
Connect anti-tip bracket to rear range foot.
Reconnect the anti-tip bracket, if the range is moved.
Failure to follow these instructions can result in death
or serious burns to children and adults.
1. Determine which mounting method to use: floor or wall.
If you have a stone or masonry floor, you can use the wall
mounting method.
2. Determine and mark centerline of the cutout space. The
mounting bracket must be installed on the right side of the
cutout. Position mounting bracket in cutout as shown in the
following illustration.
Measurement B:
30" (76.2 cm) ranges: 11%" (29.5 cm)
36" (91.4 cm) ranges: 145%" (87.1 cm)
48" (121.9 cm) ranges: 20%" (52.4 cm)
Measurement C:
Optional distance from backwall. If backwall is constructed
of a combustible material and a backguard is not installed,
a 6" (15.2 cm) minimum clearance is required for all models.
Install anti-tip bracket accordingly.
A
'
[
|
'
|
|
'
'
i
A. Centerline
B. Centerline of cutout to centerline
of anti-tio bracket
C. Backwall to back of range
3. Drilltwo 4%" (8.0 mm) holes that correspond to the bracket
holes of the determined mounting method. See the following.
Floor Mounting
A. #12 x 15%" screws
B. Anti-tip bracket
Wall Mounting
A. #12 x 1%" screws
B. Anti-tip bracket
4. Using a Phillips screwdriver, mount anti-tip bracket to the wall
or floor with the two #12 x 1%" screws provided.
Depending on the thickness of your flooring, longer screws
may be necessary to anchor the bracket to the subfloor.
Longer screws are available from your local hardware store.
5. Move range close enough to opening to allow for electrical
connections to be made. Remove shipping base, cardboard
or hardboard from under range.
6. Continue installing your range using the following installation
instructions.
11

30" (76.2 cm) and 36" (91.4 cm) Models 48" (121.9 cm) Models
a a
Electrical Shock Hazard Electrical Shock Hazard
Disconnect power before servicing. Disconnect power before servicing.
Use a new 40 amp power supply cord. Use a new 50 amp power supply cord.
Plug into a grounded outlet. Plug into a grounded outlet.
Failure to follow these instructions can result in death, Failure to follow these instructions can result in death,
fire, or electrical shock. fire, or electrical shock.
1. Disconnect power. 3. Add power supply cord strain relief.
2. Remove the terminal block cover screws and disengage m Assemble a UL listed strain relief in the opening.
mounting tabs to remove terminal block cover from back of
range.
A. Phillips head screws A. UL listed strain relief
B. Terminal block cover
C. Two mounting tabs at bottom
mg Tighten strain relief screw against the power supply cord.
4. Complete installation following instructions for your type of
electrical connection:
4-wire (recommended)
3-wire (if 4-wire is not available)
12

Electrical Connection Options
If your home has: And you willbe Go to Section:
connecting to:
4-wire receptacle A UL listed, 4-wire connection:
(NEMA type 14-50R) = 250-volt Power supply cord
minimum,
40- or 50-amp,
O range power
[] 1 | supply cord
3-wire receptacle A UL listed, 3-wire connection:
(NEMA type 10-50R) = 250-volt Power supply cord
minimum,
40- or 50-amp,
range power
supply cord
4-wire connection: Power supply cord
Use this method for:
New branch-circuit installations (1996 NEC)
Mobile homes
Recreational vehicles
In an area where local codes prohibit grounding through the
neutral
Remove the ground-link screw from the range frame. Save
the ground-link screw. Bend the ground link away from the
range so that it does not contact the range.
A. Ground-link screw
B. Ground link bent away from range
Connect the green ground wire from the power supply cord to
the range using the ground-link screw. The ground wire must
be attached first and must not contact any other terminal.
Use a 4%" nut driver to remove the hex washer head screws
from the terminal blocks.
~
Connect the neutral (center) wire to the center terminal
connector using one of the hex washer head screws.
Securely tighten screw for proper electrical connection.
A. Line 1
B. Green ground wire
C. Ground-link screw
D. Hex washer head screw
E. Silver-colored terminal
block screw
F. Ground link
G. Neutral (center) wire
H. Line 2
|. UL listed strain relief and
40- or 50-amp range
power supply cord
Connect the other 2 wires (lines 1 and 2) to the outer
aluminum terminal blocks.
Securely tighten screws for proper electrical connection.
Tighten strain relief screws.
Replace terminal block cover.
3-wire connection: Power supply cord
Use this method only if local codes permit connecting cabinet-
ground conductor to neutral wire of power supply cord.
1.
2.
Use a %" nut driver and remove the hex washer head screws
from the aluminum terminal blocks.
Connect the neutral (center) wire to the center terminal
connector using one of the hex washer head screws.
Securely tighten screw for proper electrical connection.
A. Line 1
B. Ground link
C. Hex washer head screw
D. Silver-colored terminal
block screw
E. Neutral (center) wire
F, Line 2
G. UL listed strain relief
and 40- or 50-amp range
power supply cord
Connect the other 2 wires (lines 1 and 2) to the outer terminal
screws on the terminal block.
Tighten strain relief screws.
Replace terminal block cover.
13

Install Model W10049700 Water Filter Connect to Water Filter Inlet (yellow)
1. Install the water filter near the cold water supply pipe under
the kitchen sink to filter the cold water.
IMPORTANT: Be sure to allow a minimum clearance of
1¥2" (8.8 cm) under the filter system for removing the filter
cartridge.
Make sure that the water filter assembly is installed in the
upright position.
Typical Installation Configuration
NOTE: For unique installations, contact a licensed plumber.
In Massachusetts a licensed plumber is required and the
Commonwealth of Massachusetts Plumbing Code 248-CMR
shall be adhered to.
Water suppl
ith Am line to oven
— stem x
erry aa .
| hy
Cold water THe L. 1
supply il ae |
.
Hot
Coid~
Filter
Assembly
1 Fie Supp ly
—_ line to cold
7 water supply
2. Attach the supplied water filter mounting ring and screw at
the recommended location.
3. Attach filter to the mounting ring.
1%" (3.8 cm) clearance t
Connect to Home Water Supply
1. Make connection to the cold water supply line.
m A leak-tight connection to the 4" flexible codes approved
water supply line must be provided.
Check local codes for type of connection required.
Flexible codes approved water supply line must be cut with a
tubing cutter so the ends are concentric and without burrs.
NOTE: It is recommended that the cold water line be soft water.
14
NOTE: Use the quick connect stem and/or elbow adapter fittings
in the combination needed for your installation configuration.
1. Attach the supplied %" to %" stem or %" to 4%" elbow quick
connect adapter fitting to the yellow water filter inlet
connection by pushing the quick connect fitting past the
o-ring until you hit the backstop.
3
A. Quick connect elbow adapter fitting
B. Quick connect stem adapter fitting
2. Connect the flexible codes approved water supply line (not
provided) from the home cold water supply pipe to the quick
connect adapter fitting you just installed on the filter inlet
(yellow) side of the water filter.
3. Pull tube to ensure it is secured.
A B C
A. %«" water supply tubing
B. O-ring
C. Backstop
If you need to release tubing:
Push in collet to release tubing. With collet held in, pull tubing
straight out.
A. Collet
Connect to Water Filter Outlet (blue)
1. Attach the supplied %" to %" stem or %" to 44" elbow quick
connect adapter fitting to the blue water filter outlet
connection by pushing the quick connect fitting past the
o-ring until you hit the backstop.
2. Connect another piece of flexible codes approved water
supply line to the quick connect adapter fitting you just
installed on the filter outlet (blue) side of the water filter.

3. Pull tube to ensure it is secured.
Water supply tubing to range
supply
Water supply tubing Blue
Shutoff
to
cold
water
supply
WATER
valve
OUT
Filter
4. Route flexible codes approved water supply line through
undersink cabinet and oven cabinet cutout.
5. Connect the flexible codes approved water supply line to the
range copper tubing, using a 4" to 44" water supply union.
B JP
A. To home water supply
B. Rear of cabinet cutout
C. Flexible codes approved water supply line from home
water supply
D. %" to ¥4" water supply union (supplied in water filter kit)
E, Oven copper tubing
F. Range front
6. Turn on water supply.
7. Check all connections for leaks.
NOTE: No flushing or conditioning of the water filter is required
prior to use.
AWARNING
Explosion Hazard
Use a new CSA International approved gas supply line.
Install a shut-off valve.
Securely tighten all gas connections.
If connected to LP, have a qualified person make sure
gas pressure does not exceed 14" (36 cm) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death, explosion, or fire.
1. Assemble flexible connector from gas supply pipe to pressure
regulator located in the middle rear of the range.
2. Apply pipe-joint compound made for use with LP gas to the
smaller thread ends of the flexible connector adapters (see B
and G in the following illustration).
3. Attach one adapter to the gas pressure regulator and the
other adapter to the gas shutoff valve. Tighten both adapters.
4. Use a '%e" combination wrench and channel lock pliers to
attach the flexible connector to the adapters. Check that
connector is not kinked.
A. Gas pressure regulator
B. Use pipe-joint compound.
C. Adapter (must have 2" male
pipe thread)
D. Flexible connector
E. Manual gas shutoff valve
F. ¥2" or %4" gas pipe
G. Use pipe-joint compound.
H. Adapter
Complete Connection
1. Open the manual shutoff valve in the gas supply line. The
valve is open when the handle is parallel to the gas pipe.
A. Closed valve
B. Open valve
15

2. Test all connections by brushing on an approved
noncorrosive leak-detection solution. If bubbles appear, a
leak is indicated. Correct any leak found.
3. Remove cooktop burner caps and grates from parts
package. Place burner caps on burner bases. Place burner
grates over burners and caps.
4. Check that the range is plugged into the appropriate outlet
(see the “Electrical Requirements” section).
5. Turn on power supply. For further information, please refer to
the user instructions located in the Use and Care Guide.
ar
=
Pe
1. Turn all 4 leveling rods 1 full turn to raise the range and
provide enough clearance for the rear leveling leg to slide into
the anti-tip bracket.
2. Move range into its final location making sure rear leveling leg
slides into anti-tip bracket.
NOTE: If installing the range in a mobile home, you must secure
the range to the floor. Any method of securing the range is
adequate as long as it conforms to the standards in the “Location
Requirements” section.
NOTE: Range must be level for satisfactory baking performance.
1. Place rack in oven.
2. Place level on rack and check levelness of the range, first
side to side; then front to back.
3. If range is not level, adjust the leveling rods. Turn leveling
rods located behind the kickplate to level range and to raise
or lower range to the desired countertop height.
NOTE: All roller feet must be off the floor upon final installation.
A. Front leveling rod
B. Rear leveling rod
16
A. Grill front
B. Rear tabs and slots
2. Cut and remove tie strap from rear of burner assembly.
A. Tie strap
3. Lift burner assembly up and out to remove.
4. Slide drip tray into opening on the right front side of the grill
basin. There are guides to assure correct placement of the
drip tray.
A. Drip tray
5. Insert the large grease tray all the way under the back edge of
the grill basin and hook it into the slots.
A. Large grease tray
B. Slots

6. Insert the small grease tray all the way under the front of the
grill basin and hook it into the slots.
When the 2 grease trays are installed properly, the small
grease tray will hook over the large grease tray.
[.
The griddle is factory installed.
|| LIL 1. Place drip tray in the well at the front of the griddle. Slide tray
~ toward the back until it stops.
1
A. Large grease tray
B. Grease tray connection
C. Small grease tray
D. Slots
7. Insert the orifice tube on the front of the burner assembly into
the opening at the front of the grill basin and set burner
assembly into place.
A. Griddle drip tray
B. Griddle
2. Clean griddle before using. Refer to the Use and Care Guide.
Install Burner Heads and Caps
Install the burner head, making sure the alignment pins are
properly aligned with the burner base. Place burner cap (black)
on top of the burner head.
20,000 Btu/h Ultra Power™ Dual-Flame
A. Front opening Burner
8. Insert front tabs of the flame spreader into slots at the front of
the grill basin, then the rear tabs into the rear slots.
A. Incorrect
B. Correct
B
15,000 Btu/h Professional Burner
A. Incorrect
B. Correct
A
A. Front tabs and slots 5,000 Btu/h Simmer/Melt Burner
B. Rear tabs and slots
eee
9. Check the surface burner and grill flames. Refer to the te A. Incorrect
“Electronic Ignition System” section.
10. Place the wave tray on top of the flame spreader.
B. Correct
eae
iT
rT
OQ
TU
renner
11. Place the grill grate into position.
17

Initial Lighting and Gas Flame Adjustments
Cooktop burners use electronic igniters in place of standing
pilots. When the cooktop control knob is turned to any position,
the system creates a spark to light the burner. This sparking
continues until the flame is lit or the knob is turned to Off.
Check Operation of Cooktop Burners
Push in and turn each control knob to the “LITE” position.
The surface burners and grill flames should light within
4 seconds. The first time a burner is lit, it may take longer than
4 seconds to light because of air in the gas line.
After verifying the proper burner operation, turn the control knobs
to OFF.
If burners do not light properly:
m= Turn cooktop control knob to the “OFF” position.
m Check that the range is plugged in and the circuit breaker has
not tripped or the fuse has not blown.
m Check that the gas shutoff valves are set to the “open”
position.
m Check that burner caps are properly positioned on burner
bases.
Repeat start-up. If a burner does not light at this point, contact
your dealer or authorized service company for assistance.
Flame Height
The cooktop flame should be a steady blue flame approximately
¥4" (0.64 cm) high.
Dual Flame Burner
A. Upper flame
B. Lower (simmer) flame
Single Flame Burner
To Adjust Flame Height:
1. Unplug range or disconnect power.
2. Remove burner grates.
3. Remove the control knobs.
18
4. Open the oven door and remove the 2 screws on each side of
the range that hold the control console in place.
NOTE: Make sure to leave oven door open or the control
console will not rest in the side brackets properly once it is
detached.
5. Pull up on the control console and let it drop forward into the
notched console brackets on each side.
A. Control console bracket
> Remove the round gasket from the valve stem.
Put a control knob onto the valve stem of the burner you want
to adjust.
~
8. Turn the control knob to LO and using a butane extension
lighter, light the burner.
9. Remove the control knob.

10. Use a Ye" x 414" flat-blade screwdriver to adjust the flame
height. Tighten screw to reduce flame height. Loosen screw
to increase flame height.
NOTE: When you are converting to LP gas, the screw should
be tightened down completely.
See
QR A
Ae
A B
A. Single flame burner adjustment screw (on right side of valve)
B. Dual flame burner adjustment screw (on left side of valve)
11. When finished adjusting the flame height, put a control knob
back onto the valve stem and turn off the burner.
12. Remove the control knob.
13. Replace the round gasket.
14. Repeat steps 6 through 13 for any other burners that need
adjustment.
15. Lift up on the control console and set it back into place. For a
proper fit, the flange of the control console must hook over
the lip on the front of the range cooktop.
A. Control console flange
B. Front lip of range cooktop
16. Check that the control console is flush with the top edge of
the range.
A. Flush with range top
17. Replace the 2 screws on each side of the control console.
18. Replace the control knobs.
19. Replace burner grates.
20. Test the flame by turning the control from LO to HI, checking
the flame at each setting.
4
1. Align shoulder screw mounting holes with shoulder screws on
range.
2. Push kickplate up against front of range until the top screw
holes are aligned with the mounting holes on the front of the
range.
3. Reattach screws to the top of the kickplate.
& oe rato bE OLE
A. Kickplate
B. Reattach these screws.
C. Top screw hole
D. Shoulder screw mounting hole
1. Check that all parts are now installed. If there is an extra part,
go back through the steps to see which step was skipped.
2. Check that you have all of your tools.
3. Dispose of/recycle all packaging materials.
4. For oven use and cleaning, read the Use and Care Guide.
Check Operation of Oven(s)
1. Turn power on.
2. Start a Bake cycle. See the Use and Care Guide for operating
instructions.
If oven(s) does not operate, check the following:
m Household fuse is intact and tight; or circuit breaker has
not tripped.
mw Electrical supply is connected.
m See “Troubleshooting” section in the Use and Care Guide.
3. When oven has been on for 10-15 minutes, open the oven
door and feel for heat.
If you do not feel heat or if an error code (“F” followed by a
number plus “E” followed by a number) appears in the
display, turn off the oven and contact a qualified technician.
4. Touch OFF.
To set the clock and other oven functions, refer to the Use and
Care Guide.
If you need Assistance or Service:
Please reference the “Assistance or Service” section of the Use
and Care Guide or contact the dealer from whom you purchased
your range.
19

GAS CONVERSIONS
IMPORTANT: Gas conversions from Natural gas to LP gas must
be done by a qualified installer.
AWARNING ‘
2.
Explosion Hazard
Install a shut-off valve.
Securely tighten all gas connections.
If connected to LP, have a qualified person make sure
gas pressure does not exceed 14" (36 cm) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death, explosion, or fire.
Use a new CSA International approved gas supply line.
©
Tip Over Hazard
A child or adult can tip the range and be killed.
Connect anti-tip bracket to rear range foot.
Reconnect the anti-tip bracket, if the range is moved.
Failure to follow these instructions can result in death
or serious burns to children and adults.
1. Turn the manual shutoff valve to the closed position.
2. Unplug range or disconnect power.
A. To range
B. Shutoff valve (closed position)
C. Gas supply line
20
To Convert Gas Pressure Regulator
Remove the access cap by using a wrench, turning the
access cap counterclockwise.
Remove spring retainer from the cap by pushing against the
flat side of the spring retainer. Look at the spring retainer to
locate the “NAT” or “LP” position. Turn over the spring
retainer so the “LP” is showing on the bottom. Snap the
spring retainer back into the cap. Reinstall the cap onto the
regulator.
E D C
A. Access cap
B. Gasket
C. Gas pressure regulator
D.LP position
E, NAT position
Test the gas pressure regulator and gas supply line.
The regulator must be checked at a minimum 1” (2.5 cm)
water column above the set pressure. The inlet pressure to
the regulator should be as follows for operation and checking
the regulator setting:
LP Gas:
Minimum pressure 11" (27.9 cm) WCP
Maximum pressure 14” (85.5 cm) WCP.
Gas Supply Pressure Testing
Gas supply pressure for testing regulator must be at least
1" water column pressure above the manifold pressure
shown on the model/serial rating plate.
Line pressure testing above ‘2 psi gauge (14" WCP)
The range and its individual shutoff valve must be
disconnected from the gas supply piping system during any
pressure testing of that system at test pressures in excess of
Ye psi (8.5 kPa).
Line pressure testing at 2 psi gauge (14" WCP) or lower
The range must be isolated from the gas supply piping
system by closing its individual manual shutoff valve during
any pressure testing of the gas supply piping system at test
pressures equal to or less than % psi (3.5 kPa).
To Convert Surface Burners
If the burner grates are installed, remove them.
Remove burner cap.
Remove the burner head.
NOTE: A “" socket must be used to remove the burner head
of the large dual burners.