KJM SL100 Installation guide

Page1
SL100
LED Searchlight with Wired Remote Control
Installation and Operating Guide

Page2
KJM is dedicated to providing the finest in shipboard equipment. TheSL100LEDSearchlightisbuilt to withstand the harsh
marine environment, and is designed by people with over three decades of experience in the marine industry. Built to
exacting standards from the finest materials, KJM products are rugged, available in a wide variety of styles and
configurations
Please read the following pages before attempting installation to ensure complete understanding of the KJM
SL100 LED Search Light.
Precautions
To reduce the risk of electric shock, do not remove disassemble the search light as there are no user serviceable parts
inside.
If you require additional support for the installation or use of this search light please contact us via email at
[e-mail]
FEATURES
LED lighting
Slow and fast rotation speeds
360 degree Unlimited Rotation
Wired Remote Control with 19’ of cable
120 degree Tilt
UV Ray and Saltwater Resistant
IN THE BOX
SL100 Searchlight
Routing Cable and Power and remote wiring harness
Stainless Steel Mounting Hardware
Remote control
Rubber Gasket
Installation and Operating Guide
ACCESSORIES
EC100 –13’ (4 M) Controller Extension Cable

Page3
INSTALLATION
PLANNING
The SL100 Searchlight is supplied with a 10” cable and a waterproof plug pre-installed. This allows the searchlight to be easily
removed without cutting wires. One 19’ Extension Cable with pre-installed waterproof connectors and a power and remote
harness is supplied
Note:
a. If the connectors on the 19’ extension cable are too large to run through the vessel, the cable may be cut and spliced
(wire color to wire color) by using heat shrink type butt connectors, or soldering and heat shrink.
b. If the supplied Routing Cable will not reach from the SL100 to the Remote Control, optional 13’ (EC100) Extension
Cables are available. The Routing cable may be extended up to 100 feet using 12 or larger gauge cable.
The SL100 is capable of being connected to 12 or 24VDC. Current draw: Approximately 2.3A at 12 VDC / 1.2A at 24VDC
MOUNTING THE SEARCHLIGHT
1. Find a location on the deck or radar arch with suffecient strength (SL100 weight
- 4.2 pounds) to hold the search light in place.
2. Using the SL100 Rubber Gasket as a template and a pencil/pen, mark the 4
mounting screw holes.
3. Mark a dead center point between the 4 mounting base screws for the power
and controller cable.
4. Drill the four holes using 3/8”(9mm) for the search light base power and
controller cable how using a 1” (25mm) hole saw.
5. Install the rubber gasket onto the searchlight.
6. Carefully feed the SL100 cable through the 1” hole and attached the base with
4 mounting bolts, carefully so not to pinch the power and controller cables.

Page4
MOUNTING THE REMOTE CONTROL
Note:The remote control is waterproof and may be mounted in a exposed
location. However it is recommended to protect the remote from water when not
in use.
1. Find a location large enough to mount the remote controller
2. Using the remote as a template and the dimension image and mark the
screw holes and cable cutout location.
3. Drill 4 pilot holes and cut out a 1.2”W x 0.80 hole as shown in the drawing.
4. Connect the cable to the remote controller and attached the controller
with 4 stainless wood screws carefully so not to pinch the controller
cable.
OPERATION
Press UP/Down or Left/Right keys to move rotate the searchlight.
Press the ON/OFF key will turn the search light beam on or off.
DUAL SPEED
After pressing the ON/OFF button, press and hold the Left and Right buttons simultanously until
The backlight changes.
Red LED illumination: Fast speed mode
Blue LED illumination: Slow speed mode

Page5
SPECIFICATIONS
Beam Angle
3° vertical 4.8° horizontal
Lamp Type
8 High Intensity Cree LED's
Brightness (Candela)
212,000
Rotation Speed
20° per sec (high) / 10° per sec (low)
Continuous Rotation
Yes
Size
7.2"W x 6.7"H x 5.9"D
Elevation Angle
120° total - 60° up/down
Mounting Base
6" Square
Elevation Speed
17° per sec (high) / 9° per sec (low)
Speeds
Two
Input Voltage
12 and 24VDC
Weight
4.2 Pounds
Lamp Rated Life
50,000
Plastic Housing
ASA Resin
FCC STATEMENT
NOTE: This equipment has been tested and found to comply with the limits for a Class “A”digital device, pursuant to Part15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the users will be required
to correct the interference at their own expense.
LIMITATION OF LIABILITY
This publication is provided “AS IS” without warranty of any kind, either express or implied, including but not limited to,
the implied warranties of merchantability, fitness for any particular purpose, or non-infringement of the third parties right.
This publication could include technical inaccuracies or typographical errors. Change are added to the information herein,
at any time, for the improvements of the publication and/o the corresponding product(s).
WARRANTY / CONTACT
KJM warrants its products to be free of defects in materials and workmanship for 2years. KJM's obligation under this warranty is
limited to repair or replace defective products. No material will be repaired or replaced without written authorization from KJM.
Repair or replacement will be made only after an examination indicates defective material or workmanship at time of
manufacture. KJM is in no event liable for consequential damages, installation costs or other costs of any nature incurred as a
result of the use of the products manufactured by KJM, whether used in accordance with instructions or not. All shipping costs
on returned material are the responsibility of the purchaser. KJM is not liable for repair or replacement of any product damaged
by lightning, other natural phenomena or incorrect installation including reverse polarity connections. This warranty is in lieu of
all others, either expressed or implied. Proof of purchase is required.