KJstar Z07-5 User manual

Bluetooth Monopod Selfie Stick
Product Manual
V1.0
Model: Z07-5
Thanks very much for using Bluetooth Monopod Selfie Stick from Kjstar. This
product is based on Bluetooth HID wireless communication technology, currently
suitable for the products had installed iOS4.0 and android3.0 or later. Please make
sure that your products can support the system before using.
1. Function
Autodyne and video wirelessly by Mobile
2. Description of the whole package
Bluetooth Monopod Selfie Stick:1 piece
Phone Clamp:2 piece
USB Charging Cable:1 piece
Product Manual:1 piece
Warranty Card:1 piece
3. Specification
3.1 Working environment tempersture-10℃-+40℃
3.2 Working environment relative
Humidity:10%-90%
3.3 Battery Capacity:45mAH
3.4 Charging Voltage:DC 5.0V
3.5 Charging Time:1 hour
3.6 Autodyne Frequence:500 times:
3.7 Standby Time:100 hours
3.8 Memory quantity:4 times:
3.9 The product automatically goes to “sleep” within 2 hours unused, It will
“wake up” 5 seconds later after pressing the key of “press”
4 Usage instructions
4.1 Full charging time:1hour
4.2 Pairing: Mobile phone and Monopod Apple iOS System: open the
“Setting”→Bluetooth→turn on monopod→Searching autodyne system
“kjstar” →enter the system→complete Pairing Android System:open the
“Setting” →Bluetooth→SCanning→turn on mono-pod→Serching autodyne
system“kjstar” →enter the system→complete Pairing

zThe pairing of camera and monopod need not password.The paieing
is on-going when the blue led light is flashing quickly please operate it
within 40 seconds,otherwise, you need to restart the power,rescan and
repair.
4.3 Autodyne
Put the mpbile phone to the monopod→enter camera application“ ”
→stretch themonopod→press the key of “press”
zIf the Android system can ont work well normally, please
doewnload:kjstar365 Profess-ional Autodyne Software.
5. Caution and safety
5.1 Please read the instruction carefully before usage;
5.2 Please turn off the nearby Bluetooth to avoid the signal interference;
5.3 It may conflict when using some mobile phone keyboard with it
simultaneously, please close the Bluetooth or turn off the power of monopod.
5.4 Safety
5.4.1 Please do not dismantle the product: ;
5.4.2 Please do not use corrosive solvent to clean it;
5.4.3 Forbidden to use it or charging under high temperature or strong light;
5.4.4 Forbidden to use it in the rain with damp or soaked;
5.4.5 Forbidden to throw it into fire,so as to avoid explosion;
5.5.6 Please do not knock it heavily.
6. Other cautions:
6.1 No Power of Power turnsd off:
LED turned off
6.2 Bluetooth Pairing:Blue LED
6.3 Taking photo:Blue LED Light flash one time
6.4 Blue Pairing Successfully or Wake up
Sleep:LED Light keep flashing quickly.
6.5 Low voltage:led Light keep flashing slowly.
6.6 Charging:Red LED Light on; Full Charg-ing Red LED light off.
7. FCC statement:
Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.