KK Hobby AERO SUBARU 30EP User manual

Before commencing assembly,please read these instructions thoroughly.
WING SPAN:54in
AERO SUBARU 30EP
SAFETY PRECAUTIONS
This radio control model is not a toy!
First-time builders should seek advice from people having building
experience in order to assemble the model correctly and to produce
its performance to full extent.
,
Assemble this kit only in places out of children s reach!
Take enough safety precautions prior to operating this model.
,
You are responsible for this model s assembly and safe operation!
Always keep this instruction manual ready at hand for quick
reference,even after completing the assembly.
SPECIFICATION
Warning!
！
Wing Span ....... 1370 mm (54 in)
2
Wing Area ........31.8 dm (493sq.in)
Total Length .....1067mm (42 in)
Empty weight.......1350g
Electro power.... FSD FC3548-5T Kv890
Prop.........11x5.5E propeller
Batterty ........14.8v 4200-5100 mAh
Radio : 4/5 channels ,4/4 servos

TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)
BEFORE YOU BEGINBEFORE YOU BEGIN
Sharp Hobby Knife Phillips Screw Driver Awl
Read through the manual before you begin ,so you will have an overall idea of what to do.
Check all parts .if you find any defective or missing parts .contact your local deater.
Symbols used throughout this instruction manual,comprise.
11
22
33
.
.
Warning!
!
Do not overlook this symbol.
2
Cut off shaded portion.
Ensure smooth non-binding
movement while assembling.
Must be purchased
separately!
Pay close attention
here!
Drill holes with the specified
Diameter(here:2mm)
Assemble left and right
Sides the same way.
Apply instant glue
(CA glue,super glue).
Apply epoxy glue.
Cut off excess.
502
C.A
L
R
A B
2mm
Install the aileron
1
A B
Cut away only
covering film.
Failure in flight
will cause your
model to crash.
Warning!
！
Rod adjuster
1.8X67mm Rod
- - - - - 2 - - - - - - 2
Horn
- - - - - - 2
2X16mm Tp Screw
- - - - - - 4

Hinge
- - - - - - 6
 
Apply epoxy glue.
2
4.2mm
4mm Washer
4X30mm Screw
- - - - 2
- - - -- - - - 2
330
12
17
12
Cut away only
covering film.
 
Ensure that the horizontal
stabiliser issecurely glued
to the fuselage.
A=A
B=B
C=C
Pay attention here!
Make sure to glue securely.
If not properly glued,a failure
in flight may occur
Warning!
！
Securely glue together, If coming off
during flihts .you’ll lose control of your
airplane which leads to accidents!
Temporarily fasten down the main wing
and check its correct position.
4
3X12mm Screw
- - - - 8
3mm Washer
- - - -- - - - 4
25mm
- - - - 4
Elevator servo
Rudder servo
5
Assemble the wings to the fuselage with screw
Horizontal /Vertical tail
Install the motor
Install the servo
3

1
1.8x370mm
Front-wheel Rod
2
1
3X3mm Screw
Rocker arm
4mm Nylon Collar
4mm Metal Collar
2
3
6
Elevator Rod
2X12mm Tp Screw
Rod adjuster
Horn
3
6
3
31
Elevator Rod
22
4mm Metal Collar
3X5mm Screw
- - - - - 1
Elevator rod
7
3x3mm Screw
2
4.2mm Collar
2
4mm Nylon Collar
2
8
4
3x12mm Tp Screw
Pressure Plate
Undercarriage
8
Front-wheel drive
10
Posotion Determine
85~90mm
27mm
27mm
55mm
24mm
55mm
24mm
AILERON
ELEVATOR
RUDDER
10mm
10mm
13mm
13mm
20mm
20mm
75-80mm
Intall the cowling
9
Elevator.Connect the
linkage rod to the horn
4
2.6x12mm Tp Screw
4
rudder Rod
- - - - - 1