KLIK Boks User manual

KLIK Boks Quick Start Guide
Default Settings Password: admin
Default Administration Password: adminpwd
Default Wi-Fi Mode IP Address: 192.168.59.254
1) Use either VGA or HDMI to connect the KLIK Boks to your display or projector.
2) Connect Power Supply and press
Power button once to turn On.
NOTE: Only one video
output will be active at a
time. Use either HDMI or
VGA but not both.
NOTE: For more setup and operating information refer to the User Manual
NOTE: Steps 1 - 4 are one-time setup. Step 5 is for Users.
NOTE: If the KLIK Boks name does not appear in the Connection Manager,
check that Network Discovery is enabled. Alternately, enter the IP Address
displayed on the KLIK Standby Screen to connect.
7) The KLIK Boks will restart and display that it is in now connected to the Wi-Fi
network shown. Users are directed to connect to the same wireless network in
order to stream content to the KLIK.
1) Locate the program icon and start the software.
2) When the Connection Manager appears, select the KLIK Boks by name,
enter the displayed Password and press Connect.
3) Once connected you will see the KLIK Player. To mirror your screen simply
press Play!
Page 4 Page 1
Copyright 2018 KLIK Communications Inc. - All Rights Reserved www.klikboks.com - Document QSG8.1.0
DC5V/1A
SPDIF L R HDMI VGA LAN
1Connect KLIK Boks to Display
Download & Install from www.klikboks.com or the App Store for your device.
NOTE: KLIK may also be used without software installation. Windows, Mac, iOS and
Android users can connect using their native streaming utilities.
3Install KLIK Software
NOTE: To connect with Wi-Fi follow the instructions in
the Section 4, “Add KLIK to a Wireless Network”.
VGA LAN
Use an Ethernet Cable to connect to your existing router
2Add KLIK to a Wired Network
5Launch KLIK Software and Start Streaming
4Add KLIK to A Wireless Network

First, Connect to KLIK using Wi-Fi
1) Power on the KLIK Boks and conrm that the Standby screen is shown on the
presentation display:
4) Select Wireless Settings
from the menu on the left,
then click on the Wi-Fi Connec-
tion tab to navigate to the
Wi-Fi pairing screen.
5) Click on the “Scan for Wi-Fi”
button to search for the
wireless access point that KLIK
will be connected with . This
could take up to 2 minutes to
complete. Select the preferred
wireless Access Point (AP)
from the list.
NOTE: If you change the Device Name at this stage, you must reconnect using the
new name as in section 4b in order to continue setup.
NOTE: Connect to KLIK as if you are connecting to a Wi-Fi network.
6) Enter the password for your
selected Wi-Fi Access Point
and click Submit. The KLIK
Boks will terminate broadcast-
ing its SSID and will connect
to the Wi-Fi network. Any
connected devices will be
disconnected.
This is the Wi-Fi signal name
being broadcast by KLIK. Connect
to this SSID as shown below.
This is the Device ID, the default
name of the KLIK Boks. It can be
changed during Setup.
Ready for Connection
Windows Mac
2) Open your computer’s Wireless Network connection manager and select the
KLIK Boks by name. Press Connect. No password is required.
3) Open a browser window
and navigate to the KLIK Boks
IP address shown in the
Standby screen (default is
192.168.59.254). Enter the
password (Default is admin)
and click Sign In.:
Page 2 Page 3
Copyright 2018 KLIK Communications Inc. - All Rights Reserved www.klikboks.com - Document QSG8.1.0
4Add KLIK to A Wireless Network 4Add KLIK to A Wireless Network