Klimaire KSIA009-H216-I User manual

Please read this owner s manual carefully and
thoroughly before operating the unit!
Take care of this manual for future reference.
※
※
roleoo
※
※
Please read this owner s manual carefully and
thoroughly before operating the unit!
Take care of this manual for future reference.
※
※
,
,
KSIA SERIES
SPLIT TYPE ROOM
AIR CONDITIONER
For Split Wall Mounted
Series R410a Inverter
Model Type For F
KSIA009-H216-I / KSIA009-H216-O
KSIA012-H216-I / KSIA012-H216-O
KSIA018-H216-I / KSIA018-H216-O
KSIA024-H216-I / KSIA024-H216-O

10
4.1 Error Code
Cha
pter
4
Troubleshooting Guide
(4-way valve swich failure)
No. Error Code Problem
1E1 Room temperature sensor fault
2E2 Outdoor coil temperature sensor fault
3E3 Indoor coil temperature sensor fault
4E4 Indoor fan motor or DC motor feedback fault
5E5 Indoor & outdoor communication fault
6F0 Outdoor DC Fan motor fault
7F1 IPM modular fault
8F2 PFC modular fault
9F3 Compressor operation fault
10 F4 Exhaust Temperature sensor fault
11 F5 Compressor top cover protection
12 F6 Outdoor ambient temp sensor fault
13 F7 Over/under voltage protection
14 F8 Outdoor modular communication fault
15 F9 Outdoor E²PROM fault
16 FA Suction temperature sensor fault

Troubleshooting Guide
11
4.2
1. The Foremost Inspecting Items
⑴The input voltage must be within +10% tolerance of the rated Voltage. If it
is not the case, the air-conditioner will probably not work normally.
⑵Check the connecting cord between indoor unit and outdoor unit to see if
it is properly connected. The connecting must be done according to the
wiring diagram, please also notice that even different models may have the
connecting cord of the same specification.
Please check if the marks at the connecting terminal and the marks on the
cord can match, otherwise, the air-conditioner will not work normally.
⑶If the following phenomena are found, the problem is not from the
air-conditioner itself.

12
5
The compressor works
discontinuously at cooling and
dehumidifying mode, and the indoor
fan motor slows down.
The compressor stops internally or the fan
motor slows down to prevent the indoor heat
exchanger from being frozen.
NO. Problems Causes
1The motor is heard operating but the
air-conditioner dose not work when
the indoor unit is powered on
Since the air-conditioner is powered on, it
will come to working condition as long as you
press the ON/OFF button of the remote
control and the Signal is well received.
2
The compressor stops running but
the indoor fan motor keeps working
when it is at cooling mode with the
indoor temperature higher than set
temperature.
If you turn off the air-conditioner and restart it
immediately, it will return to normal in 3
minutes, after that, the air-conditioner will
automatically adjust the indoor fan speed to
what you set.
3The compressor works
discontinuously at dehumidifying
mode.
The air-conditioner will automatically control
the working of the compressor according to
the inside temperature
4The air-conditioner does not work
while the LED display is on.
The TIMER is set with the air-conditioner; it
will be in hold on condition. If the TIMER
setting is cancelled, the air-conditioner will
return to normal working condition

13
2. No Power Display
⑴Items
a) Check if the input voltage is correct?
b) Check if the AC power supply connecting is correct?
c) Check if the output voltage of the manostat L7805 (IC2) is correct?
⑵Trouble shooting procedure

14
connector (CN8)?
⑵Trouble shooting procedure
3. The Indoor Fan Motor Does Not Work
⑴Items
a) Check if the indoor fan motor is connected correctly to the connector (CN8)?
b) Check if the AC input voltage is correct?
c) Check if the IC of indoor fan motor is connected correctly to the connector
(CN2)?
d) Check if the capacity of indoor fan motor is connected correctly to the

15
4. The Outdoor Unit Does Not Work
⑴Items
a) Check if the input voltage is correct?
b) Check if the wire connection of the outdoor connecting terminal is correct?
⑵Trouble shooting procedure

16
5. The Step Motor Does Not Work
⑴Items
a) Check if the input voltage is correct?
b) Check if the step motor controlling the up-down movement firmly
connected to Cn2?
⑵Trouble shooting procedure

17
6. Heating Mode Can Work, But No Hot Air Blow
⑴Check if the set temperature is lower than the indoor temperature?
⑵Check if the indoor PCB is connected to the terminal correctly?

18
7. Remote Control Can Not Work
Trouble shooting rocedure

e lare loo  a reere raear o lare Proc c
or 201 lare Proc c
2190 NW 89 Place, Doral, FL 33172 - USA
Tel: [phone]
www.klimaire.com Fax: [phone]
[email protected]